ECO mode INFINITI QX30 2017 Workshop Manual

WARNING
•Radio waves could adversely affect electri-
cal medical equipment. Those who use a
pacemake should contact their electrical
medical equipment manufacturer for the
pssible influences before use.
•If the low tire pressure warning light illumi-
nates or a tire pressure-related warning is
displayed by the vehicle information dis-
play while driving, avoid sudden steering
maneuvers or abrupt braking, reduce ve-
hicle speed, pull off the road to a safe loca-
tion and stop the vehicle as soon as pos-
sible. Driving with under-inflated tires may
permanently damage the tires and increase
the likelihood of tire failure. Serious vehicle
damage could occur and may lead to an ac-cident and could result in serious personal
injury. Check the tire pressure for all four
tires. Adjust the tire pressure to the recom-
mended COLD tire pressure shown on the
tire and loading information label to turn
the low tire pressure warning light OFF. If
you have a flat tire, replace it with a replace-
ment tire as soon as possible.
•If a replacement wheel is fitted without an
INFINITI TPMS Sensor, the TPMS will not
function and the low tire pressure warning
light will flash for approximately 1 minute.
The light will remain on after 1 minute. It is
recommended you contact an INFINITI re-
tailer as soon as possible for tire replace-
ment and/or system resetting.
•For models with run-flat tires, although you
can continue driving with a punctured run-flat
tire, remember that vehicle handling stability
is reduced, which could lead to an accident
and personal injury. Also, driving a long dis-
tance at high speeds may damage the tires.
–Do not drive at speeds above 50 MPH (80
km/h) and do not drive more than approxi-
mately 93 miles (150 km) with a punctured
run-flat tire. The actual distance the ve-
hicle can be driven on a flat tire depends
on outside temperature, vehicle load, road
conditions and other factors.
–If you detect any unusual sounds or
vibrations while driving with a punctured
run-flat tire, pull off the road to a safe
location and stop the vehicle as soon as
possible. The tire may be seriously dam-
aged and need to be replaced.
•Replacing tires with those not originally
specified by INFINITI could affect the proper
operation of the TPMS.
•If you used Emergency Tire Sealant to repair
a minor tire puncture, the TPMS sensor
should be checked when repairing or re-
placing the tire (for models equipped with
the emergency tire puncture repair kit). It is
recommended you visit an INFINITI retailer
for this service.
•INFINITI recommends using only INFINITI
Genuine Emergency Tire Sealant provided
with your vehicle. Other tire sealants may
damage the valve stem seal which can
cause the tire to lose air pressure (for mod-
els equipped with the emergency tire punc-
ture repair kit).
NSD633
5-6Starting and driving

STARTING PROCEDURE WITH THE KEY
0OFF position
1ACC position
2ON position
3START position
1. Apply the parking brake.
2. Shift the transmission to position P (Park)
by pressing the

button.
The transmission position indicator in the
vehicle information display shows

When the transmission is in position N (Neu-
tral), you can also start the engine with the
brake pedal depressed.The starter is designed not to operate if the shift
lever is in any of the driving positions.
3. Turn the key to the START position
3in the
ignition lock and release it as soon as the
engine is running.
If the engine is very hard to start because it is
flooded, depress the accelerator pedal all the
way to the floor and hold it. Turn the ignition
switch to the START position to start cranking
the engine. After 5 or 6 seconds, stop cranking
by turning the ignition switch to OFF. After
cranking the engine, release the accelerator
pedal. Crank the engine with your foot off the
accelerator pedal by depressing the brake
pedal and turning the ignition switch to start
the engine. If the engine starts, but fails to run,
repeat the above procedure.
CAUTION
Do not operate the starter for more than 15
seconds at a time. If the engine does not start,
turn the ignition key to the OFF position and
wait 10 seconds before cranking again, other-
wise the starter could be damaged.
4.Warm-up
Allow the engine to idle for at least 30
seconds after starting. Do not race the en-
gine while warming it up. Drive at moderate
speed for a short distance first, especially in
cold weather. In cold weather, keep the
engine running for a minimum of2-3
minutes before shutting it off. Starting and
stopping the engine over a short period of
time may make the vehicle more difficult to
start.
5. To stop the engine, Shift the transmission to
position P (Park) by pressing the

button.
and turn the ignition switch to the OFF
position.
NPA1483
STARTING ENGINE
5-16Starting and driving

Drive mode switch
The drive mode switch allows you to choose
between drive programs with different driving
characteristics.
Press drive mode switch
1. The selected drive
program appears in the vehicle information
display.
The automatic transmission switches to drive
program E each time the engine is started.
E (Economy): comfortable, economical driving
S (Sport): sporty driving style
M (Manual): manual gear shifting
For more details of the manual drive program
seeManual drive programlater in this section.
Steering wheel gearshift paddles
1Left steering wheel gearshift paddle
(shifts down)
2Right steering wheel gearshift paddle
(shifts up)
In drive program M, you can change gear your-
self using the steering wheel gearshift paddles.
If you pull the left or right steering wheel
gearshift paddle when in automatic drive pro-
gram E or S, the automatic transmission shifts
into drive program M for a limited time. Depend-
ing on which gearshift paddle is pulled, the
automatic transmission immediately shifts into
the next gear down or up.
Automatic drive programs
Drive program E is characterized by the follow-
ing:
•Comfort-oriented engine settings.
•Optimal fuel consumption resulting from the
automatic transmission shifting up sooner.
•The vehicle pulling away more gently in
forward and reverse gears unless the accel-
erator pedal is depressed fully.
•Increased sensitivity. This improves han-
dling on slippery road surfaces, for example.
•The automatic transmission shifting up
sooner. This results in the vehicle being
driven at lower engine speeds and the
wheels being less likely to spin.
Drive program S is characterized by the follow-
ing:
•Sporty engine settings.
•The automatic transmission shifting up
later.
•As a result of the later automatic transmis-
sion shift points, the fuel consumption pos-
sibly being higher.
NSD587NSD584
Starting and driving5-21

Deactivating the temporary manual drive program:
Pull and hold the right steering wheel gearshift
paddle until the automatic transmission shifts into
the last active automatic drive program E or S.
When manual drive program M is deactivated,
the automatic transmission in automatic drive
program E or S may shift from the current gear
into a higher or lower gear. This is dependent
on the position of the accelerator pedal, speed
and load.Problems with the transmission
:
Problem Possible causes/consequences and solutions
The transmission has problems shift-
ing gearThe transmission is losing oil.
Have the transmission checked immediately. It is recommended you
visit an INFINITI retailer for this service.
The acceleration ability is deteriorat-
ing The transmission no longer shifts
into all of the gears Reverse gear can
no longer be engagedThe transmission is in emergency mode.
•Stop.•Shift the transmission to position P (Park).•Switch off the engine.•Wait at least ten seconds before restarting the engine.•Shift the transmission to position D (Drive).•Have the transmission checked immediately. It is recommended
you visit an INFINITI retailer for this service.
5-24Starting and driving

dynamometer. Using the wrong test equip-
ment may result in drivetrain damage or un-
expected vehicle movement which could re-
sult in serious vehicle damage or personal
injury.
•When a wheel is off the ground due to an
uneven surface, do not spin the wheel
excessively.
CAUTION
Never tow the vehicle with one axle raised. This
may damage the differential. Damage of this
sort is not covered by the warranty. All wheels
must be fully raised (seeFour-Wheel Drive
(4WD) modelsin the6. In case of emergency
section)
4WD, together with VDC, improves the traction
of your vehicle whenever a drive wheel spins
due to insufficient grip.
If you fail to adapt your driving style, 4WD can
neither reduce the risk of an accident nor
override the laws of physics. 4WD cannot take
account of road, weather, and traffic conditions.
4WD is only an aid. You are responsible for the
distance to the vehicle in front, for vehicle
speed, for braking in good time, and for staying
in lane.If a drive wheel spins due to insufficient grip
•When pulling away, only depress the accel-
erator pedal as far as is necessary.
•Accelerate less when driving.
NOTE
In wintry driving conditions, the maximum effec-
tiveness of 4WD can only be achieved if you use
winter tires (M+S tires), with snow chains if nec-
essary.
WARNING
•Do not stop or park the vehicle over flam-
mable materials such as dry grass, waste
paper or rags. They may ignite and cause a
fire.
•Safe parking procedures require that both
the parking brake be applied and the P
(Park) position engaged. Failure to do so
could cause the vehicle to move unexpect-
edly or roll away and result in an accident.
•When parking the vehicle, make sure the P
(Park) position is engaged. The shift lever
cannot be moved out of the P (Park) position
without depressing the brake pedal.
•Never leave the engine running while the
vehicle is unattended.
•To help avoid risk of injury or death through
unintended operation of the vehicle and/or
its systems, do not leave children, people
who require the assistance of others, or
pets unattended in your vehicle. Addition-
ally, the temperature inside a closed vehicle
on a warm day can quickly become high
enough to cause a significant risk of injury
or death to people and pets.
PARKING
5-84Starting and driving

WARNING TRIANGLE (IF EQUIPPED)
Removing and refitting the warning
triangle
To remove:
1. Open the lift gate and lift the luggage
compartment floor upwards.2. To release warning triangle, push back the
retainers on the bracket.
3. Remove warning triangle
1from the
bracket.
To refit:
1. Place warning triangle
1back into the
bracket and push down to secure.
2. Fold down the luggage compartment floor.
3. Close the lift gate.
Setting up the warning triangle
1. Fold legs out to the side.
2. Fold side reflectors upwards to form a
triangle and lock them at the top using press
stud.
RUN-FLAT TIRES
With special run-flat tires, you can continue to
drive your vehicle even if there is a total loss of
pressure in one or more tires. The affected tire
must not show any clearly visible damage.
You can recognise run-flat tires by the marking
which appears on the tire side wall. You will
find this marking next to the tire size designa-
tion, the load-bearing capacity and the speed
index.Run-flat tires may only be used in conjunction
with an activated tire pressure loss warning
system or tire pressure monitor.
Pressure loss warning message
If a pressure loss warning message appears in
the vehicle information display:
•Observe the instructions in the display
messages.
•Check the tire for damage.
•If driving on, observe the following notes.
The driving distance possible in run-flat mode is
approximately 50 miles (80 km) when the ve-
hicle is partially laden and approximately 20
miles (30 km) when the vehicle is fully laden.
In addition to the vehicle load, the driving
distance possible depends upon:
•Vehicle speed.
•Road condition.
•Outside temperature.
The driving distance possible in run-flat mode
may be reduced by extreme driving conditions/
maneuvers, or it can be increased through a
moderate style of driving.NIC2686
6-4In case of emergency

The driving distance possible in run-flat mode is
counted from the moment the tire pressure loss
warning appears in the vehicle information dis-
play.
You must not exceed a maximum speed of 50
MPH (80 km/h).
When replacing one or all tires, observe the
following specifications for your vehicle’s tires:
•Size
•Type
•Run-flat mark
If a tire has gone flat and cannot be replaced
with a run flat tire, a standard tire may be used
as a temporary measure. Make sure that you
use the proper size and type (summer or winter
tire).
WARNING
Do not exceed the stated maximum speed.
Avoid abrupt steering and driving maneuvers,
and driving over obstacles (curbs, pot holes,
off road). This applies in particular to a laden
vehicle.
Stop driving in emergency mode if:
•You hear banging noises.
•The vehicle starts to shake.
•You see smoke and smell rubber.
•VDC is intervening constantly.
•There are tears in the sidewalls of the tire.
After driving in emergency mode, have the
wheel rims checked with regard to their further
use. It is recommended you visit an INFINITI
retailer for this service. The faulty tire must be
replaced.
REMOVING AND FITTING WHEELS
NOTE
A spare wheel is not provided with your vehicle.
Blocking the wheels
WARNING
Make sure to block the appropriate wheel to
prevent the vehicle from moving, which may
cause personal injury.
Place suitable blocks
1in front of and behind
the wheel diagonally opposite the flat tire
Ato
prevent the vehicle from moving when it is on
the jack.
MCE0001DZ
In case of emergency6-5

2. Align the center of both the jack head2and the notches at the jack-up point3as
shown.
3. Fit the groove of the jack head between the
two notches as shown.4. Loosen each wheel bolt by one or two turns
counterclockwise with the wheel wrench.
Do not remove the wheel bolts until the tire is
off the ground.
Models with wheel lock bolts (if equipped) :
If the wheel is equipped with a wheel lock
bolt, insert the wheel lock key
1and
loosen it as previously described.
The wheel lock bolt can only be removed
with the wheel lock key. A key number is
necessary if you need to duplicate the wheel
lock key.Record the key number as shown on the key
code card on the “Security information”
page at the end of this manual and keep it in
a safe place, not in the vehicle. If you lose
the wheel lock key, it is recommended you
see your INFINITI retailer for a duplicate with
the original wheel lock key code.
Make sure to keep the lock key in the
vehicle. Otherwise, wheels cannot be re-
moved and the service cannot be performed.
NCE449NCE143Z
In case of emergency6-7

5. To lift the vehicle, securely hold and turn the
ratchet handle
1clockwise as shown.
6. Carefully raise the vehicle until the tire
clears the ground.
7. Remove the wheel bolts, then remove the
wheel with the flat tire.
WARNING
The wheel is heavy. Be sure that your feet are
clear of the wheel and use gloves as necessary
to avoid injury.
Installing the wheel
WARNING
•A temporary use spare wheel and tire is
designed for emergency use.
•Never use wheel bolts other than those
provided with your vehicle. Incorrect wheel
bolts or improperly tightened wheel bolts
may cause the wheel to become loose or
come off. This could cause an accident.
•Never use oil or grease on the wheel bolts.
This may cause the wheel bolts to become
loose.ATighten
BLoosen
1. Clean any mud or dirt from the surface
between the wheel and the hub.
2. Carefully fit the wheel and tighten the wheel
bolts with your fingers. Check that all the
wheel bolts contact the wheel surface hori-
zontally and on the bevelled side.
Models with wheel lock bolt (if equipped):
Insert the wheel lock key into the wheel lock
bolt and tighten into the wheel finger tight.
3. With the wheel wrench, tighten the wheel
bolts alternately and evenly in the sequence
as illustrated (
1-5) until they are tight.
4. Lower the vehicle slowly until the tire
touches the ground.
NCE449NCE435
6-8In case of emergency

CAUTION
•Always connect positive+to positive+and negative-to body ground (for ex-
ample, strut mounting bolt, engine lift
bracket, etc.) – not to the battery’s negative
-.
•Be sure that the jumper cables do not touch
moving parts in the engine compartment
and that the cable clamps do not contact
any other metal.
9. Start the engine of the other vehicle
Aand
let it run for a few minutes. Keep the engine
speed at about 2,000 rpm.
10. Start the engine of your vehicle
Bin the
normal way.
CAUTION
Do not keep the starter motor engaged for
more than 10 seconds. If the engine does not
start right away, place the ignition switch in
the OFF position and wait 10 seconds before
trying again.11. After starting the engine of your vehicle,
carefully disconnect the negative lead and
then the positive lead (
4→3→2→
1).
12. Remove and dispose of the cloth that was
used to cover the ventilator holes as it may
be contaminated with corrosive acid.
13. Install the ventilator caps (if equipped).
14. Close the hood.
NOTE
For models which incorporate the Idle Stop/
Start System:
•Ensure that the battery fitted is the special
battery that is enhanced with regard to the
charge-discharge capacity and life perfor-
mance. Avoid using any other battery for the
Idle Stop/Start System, as this may cause
early deterioration of the battery or a mal-
function of the Idle Stop/Start System. It is
recommended that a Genuine INFINITI bat-
tery is fitted. For more information, it is
recommended you contact an INFINITI re-
tailer.
•If the battery terminal is disconnected (for
battery replacement, etc.) and then recon-
nected, there may be some delay before the
Idle top/Start System reactivates.Do not attempt to start the engine by pushing
the vehicle.
CAUTION
•Automatic Transmission (AT) model cannot
be push-started or tow-started. Attempting
to do so may cause damage to the transmis-
sion.
•Three-way catalyst equipped models
should not be started by pushing. Attempt-
ing to do so may cause damage to the three-
way catalyst.
•Never try to start the vehicle by towing it;
when the engine starts, the forward surge
could cause the vehicle to collide with the
tow vehicle.
PUSH STARTING
6-12In case of emergency