Vic INFINITI QX30 2017 Manual Online

Compact Disc (CD) player
•Do not force a compact disc into the CD
insert slot. This could damage the CD and/or
CD player.
•Trying to load a CD with the CD door closed
could damage the CD and/or CD player.
•During cold or rainy weather, the player may
malfunction due to the humidity. If this oc-
curs, remove the CD and dehumidify or ven-
tilate the player completely.
•The player may skip while driving on rough
roads.
•The CD player sometimes cannot function
when the passenger compartment tempera-
ture is extremely high. Decrease the tem-
perature before use.
•Only use high quality 4.7 in (12 cm) round
discs that have the “COMPACT disc DIGITAL
AUDIO” logo on the disc or packaging.
•Do not expose the CD to direct sunlight.
•CDs that are of poor quality, are dirty,
scratched, or covered with fingerprints, or
that have pin holes may not work properly.
•The following CDs may not work properly:
– Copy control compact discs (CCCD)
– Recordable compact discs (CD-R)
– Rewritable compact discs (CD-RW)
•Do not use the following CDs as they may
cause the CD player to malfunction.
– 3.1 in (8 cm) discs
– CDs that are not round
– CDs with a paper label
– CDs that are warped, scratched, or have
abnormal edges
•This audio system can only play prerecorded
CDs. It has no capabilities to record or burn
CDs.
•If a CD cannot be played, one of the follow-
ing messages will be displayed.
[Disc Reading Error]
Indicates a CLV/Focus, TOC or Access error.
Check and re-insert the CD. Make sure that it
is inserted correctly.
[Please Eject Disc]
Indicates a mechanism error. If the CD can be
ejected, eject and re-insert the CD. If the CD
cannot be ejected, have the system checked.
It if recommended you contact an INFINITI
retailer for this service.
[File type is not supported]
Indicates that no readable files are found on
the inserted CD. Check the data on your CD.
SAA0480
4-56Display screen, heater and air conditioner, and audio system

USB (Universal Serial Bus) connection
port/ iPod
The Media Hub is located in the center console
and consists of the USB connectors.
1) USB/iPod connection port
Connect to play media from an iPod
R,
iPhone
Ror a USB memory device. When
using INFINITI InTouch Apps with an iPhone
R, connect via a USB cable. Refer to the
device manufacturer’s owner information re-
garding the proper use and care of the
device.
WARNING
Do not connect, disconnect or operate the USB
device while driving. Doing so can be a distrac-
tion. If distracted you could lose control of your
vehicle and cause an accident or serious
injury.
CAUTION
•Do not force the USB device into the USB
port. Inserting the USB device tilted or up-
side-down into the port may damage the
port. Make sure that the USB device is con-
nected correctly into the USB port.
•Do not grab the USB port cover (if equipped)
when pulling the USB device out of the port.
This could damage the port and the cover.
•Do not leave the USB cable in a place where
it can be pulled unintentionally. Pulling the
cable may damage the port.
The vehicle is not equipped with a USB device.
USB devices should be purchased separately as
necessary.
This system cannot be used to format USB
devices. To format a USB device, use a personal
computer.
In some areas, the USB device for the front
seats plays only sound without images for
regulatory reasons, even when the vehicle is
parked.
NAA1628
Display screen, heater and air conditioner, and audio system4-57

This system supports various USB memory de-
vices, USB hard drives and iPod players. Some
USB devices may not be supported by this
system.
•Partitioned USB devices may not play cor-
rectly.
•Some characters used in other languages
(Chinese, Japanese, etc.) may not appear
properly in the display. Using English lan-
guage characters with a USB device is rec-
ommended.
General notes for USB use
:
Refer to your device manufacturer’s owner in-
formation regarding the proper use and care of
the device.
Notes for iPod use
:
iPod is a trademark of Apple Inc., registered in
the U.S. and other countries.
•Improperly plugging in the iPod may cause a
checkmark to be displayed on and off (flick-
ering). Always make sure that the iPod is
connected properly.
•An iPod nano (1st Generation) may remain in
fast forward or rewind mode if it is connected
during a seek operation. In this case, please
manually reset the iPod.
•An iPod nano (2nd Generation) will continue
to fast-forward or rewind if it is disconnected
during a seek operation.
•An incorrect song title may appear when the
Play Mode is changed while using an iPod
nano (2nd Generation)
•Audiobooks may not play in the same order
as they appear on an iPod.
•Large video files cause slow responses in an
iPod. The vehicle display may momentarily
black out, but will soon recover.
•If an iPod automatically selects large video
files while in the shuffle mode, the vehicle
display may momentarily black out, but will
soon recover.
4-58Display screen, heater and air conditioner, and audio system

Windows Media Player:
This product is protected by certain intellectual
property right of Microsoft. Use or distribution
of such technology outside of this product is
prohibited without a license from Microsoft.
Bluetooth® Audio player
The Bluetooth® word mark and logos are reg-
istered trademarks owned by Bluetooth SIG,
Inc. and any use of such marks by DENSO
CORPORATION is under license. Other trade-
marks and trade names are those of their
respective owners.
•Some Bluetooth® streaming audio devices
may not be recognized by the in-vehicle
audio system.
•It is necessary to set up the wireless con-
nection between a compatible Bluetooth®
streaming audio device and the in-vehicle
Bluetooth® module before using the
Bluetooth® streaming audio.
•The Bluetooth® streaming audio may be
stopped under the following conditions:
– When receiving a hands-free call
– When checking the connection to the
hands-free phone
– When connecting the hands-free phone
or the audio device
– When downloading a phonebook memory
from a connected cellular phone
•Do not place a Bluetooth® streaming audio
device in an area surrounded by metal or far
away from the in-vehicle Bluetooth® module
to prevent tone quality degradation and wire-
less connection disruption.
•While an audio device is connected through
Bluetooth® wireless connection, the battery
of the device may discharge quicker than
usual.
•This system supports the Bluetooth® Ad-
vanced Audio Distribution Profile (A2DP) and
Audio/Video Remote Control Profile (AVRCP).
•Wireless LAN (Wi-Fi) and the Bluetooth®
functions share the same frequency band
(2.4 GHz). Using the Bluetooth® and the
wireless LAN functions at the same time may
slow down or disconnect the communication
and cause undesired noise. It is recom-
mended that you turn off the wireless LAN
(Wi-Fi) when using the Bluetooth® functions.
Display screen, heater and air conditioner, and audio system4-63

2. Tune to the station/channel you wish to
store in the preset list.
3. (Radio screen operation) Touch and hold
one of the preset numbers in the preset list.
(Radio memory buttons operation) Push and
hold the desired station/channel preset but-
ton <1> to <6>.
4. The information such as frequency (AM/FM),
channel number (SXM), etc. will be dis-
played on the preset list.
To change the preset stations/channels, touch
and hold one of the preset numbers. You can
select whether to change the station/channel or
to delete the preset setting.
Alert notification (SXM only)
:
Favorite artists and songs can be registered to
receive an alert notice wen a song of the
registered conditions is on the radio. To tune to
the respective channel, touch [Listen to be
consistent]. The alert can be ignored by touch-
ing [Cancel].
Satellite Radio:
•The satellite mode requires and active
SiriusXM Satellite Radio subscription. The
satellite service is available only to those at
least 18 and older in the 48 contiguous
United States.
•It may take some time to receive the activa-
tion signal after the initiation of the SiriusXM
Satellite Radio subscription. After receiving
the activation signal, an available channel
list will automatially be updated in the radio.
Switch the ignition switch from LOCK to ACC
to update the SiriusXM channel list.
Radio Controls
Touch [Control] on the AM, FM or SXM screen to
display the control screen.
The following items are available:
FM/AM
:
•[Station List]
Touch to display the available station list.
While listening to FM radio, Auto Update is
not performed.
•[Scan]
Touch to scan tune the stations
SeeRadio operationearlier in this section
•[HD mode]
When this item is turned on, the analog and
digital reception switches automatically.
When this item is turned off, te reception is
fixed in the analog mode.
•[HD Info]
Touch to display the HD Radio information
such as name of song, artist and album.
This item is available when [RDS Info] is not
active.
•[Tag] (HD Radio broadcasts only)
Touch to register the tag information for
iTunes Tagging. If an iPod is plugged in after
the registration, the tag information can be
stored in an iPod and be used to purchase
the songs via iTunes.
•[RDS Info] (FM only)
Touch to display the RDS information.
This item is available only when [HD Radio
Info] is not active.
SXM
:
•[Categories]
Touch to display the category list.
•[Direct Tune]
Touch to display the keypad to enter the
frequency and directly tune to the channel.
SeeRadio operationearlier in this section
Display screen, heater and air conditioner, and audio system4-69

USB (UNIVERSAL SERIAL BUS)
CONNECTION PORT
Connecting USB memory device
WARNING
Do not connect, disconnect or operate the USB
device while driving. Doing so can be a distrac-
tion. If distracted you could lose control of your
vehicle and cause an accident or serious injury.
CAUTION
•Do not force the USB device into the USB
port. Inserting the USB device tilted or up-
side down into the port may damage the
port. Make sure that the USB device is con-
nected correctly to the USB port.
•Do not grab the USB port cover (if equipped)
when pulling the USB device out of the port.
This could damage the port and the cover.
•Do not leave the USB cable in a place where
it can be pulled unintentionally. Pulling the
cable may damage the port.Refer to your device manufacturer’s owner in-
formation regarding the proper use and care of
the device.
Two USB connectors are located on the center
console box.
USB (Universal Serial Bus) connection port/
iPod
When compatible storage devices are plugged
into the jack, compatible audio files on the
storage devices can be played through the
vehicle’s audio system.
Display screen, heater and air conditioner, and audio system4-73

How to view USB operation screen
1[Source]:
Touch to switch to the source list
screen.
Selecting audio source
2Play time:
The play time of the track is displayed.
3Track information:
Track information such as the song title,
artist name and folder name is dis-
played.
4Audio source indicator:
Indicates which of the two USB memory
device is selected.
5[USB1]/[USB2]:
Touch to switch to the other connected
USB memory device.
6Album artwork (if equipped):
An image of the CD cover is displayed
when available.
7Track number:
This indicates the track number and the
total number of tracks.
8[]/[]:
Touch to play or pause the track.
9USB menu:
USB menu items are displayed. Touch
an icon to display the list or to change
the setting.
- [Folder/Track]
- [Artists]
- [Albums]
- [Previous List]
- [Scan]
- [Play Mode]
10Play mode indicator:
This indicates the current play mode.
Touch to change the play mode.NAA1719
4-74Display screen, heater and air conditioner, and audio system

Mode Screen display
All Track Repeat
All
1 Folder Repeat
1 Folder
1 Track Repeat
1 Track
All Random
All
1 Folder Random
1 Folder
11Folder number:
This indicates the folder, artist or album
number and the total number of folders/
lists.
USB memory device player operation
Activation and playing:
USB memory device mode can also be activated
from the audio source list and the audio source
bar by the touch panel operation or by pushing
.
Selecting audio source
Main audio buttons
To play the USB memory device touch [
],
and to pause the USB memory touch []on
the USB operation screen.
Selecting play list
:
Select a play list by touching an icon in the USB
menu.
•Folder/Track (List)
•Artist (List)
•Album (List)
•Previous List
Skipping tracks/folders
:
Push to skip to the next or
previous track.
To skip to the next or previous folder, Push
.
Fast-forwarding/rewinding
:
Push and holdto fast-
forward or rewind the track. Release •CAT•TRACK> to play the track at normal speed.
Scanning
:
Touch [Scan] on the display to scan the tracks in
the USB memory device. While scanning, the
USB memory device will play the first 10 sec-
onds of each track and move on to the next
track. Touching [Scan] again within the 10 sec-
onds will stop scanning.
Changing play mode
:
Touch [Play Mode] on the display to select the
play mode.
Only one of the two connected USB memory
devices can be operated by the voice recogni-
tion system.
IPOD PLAYER
Connecting iPod
WARNING
Do not connect, disconnect or operate the iPod
while driving. Doing so can be a distraction. If
distracted you could lose control of your ve-
hicle and cause an accident or serious injury.
CAUTION
•Do not force the iPod device into the USB
port. Inserting the iPod cable tilted or up-
side down into the port may damage the
port. Make sure that the iPod cable is con-
nected correctly to the USB port.
•Do not grab the USB port cover (if equipped)
when pulling the iPod cable out of the port.
This could damage the port and the cover.
•Do not leave the iPod cable in a place where
it can be pulled unintentionally. Pulling the
cable may damage the port.
Refer to your device manufacturer’s owner in-
formation regarding the proper use and care of
the device.
Display screen, heater and air conditioner, and audio system4-75

Two USB (iPod) connectors are located on the
center console box.
USB (Universal Serial Bus) connection port/
iPod
The battery of the iPod will be charged while the
device is connected to the vehicle if the iPod
supports USB connection charging.
Depending on the model and firmware version
of the iPod, the display on the iPod shows an
INFINITI or Accessory Attached screen when the
connection is completed. When the iPod is
connected to the vehicle, the iPod music library
can only be operated using the vehicle audio
controls.
Compatibility
:
Made for
•iPod touchR(5th generation)
•iPod touchR(4th generation)
•iPod touchR(3rd generation)
•iPod touchR(2nd generation)
•iPod touchR(1st generation)
•iPod touchR
•iPodRwith video
•iPod classicR
•iPod nanoR(7th generation)
•iPod nanoR(6th generation)
•iPod nanoR(5th generation)
•iPod nanoR(4th generation)
•iPod nanoR(3rd generation)
•iPod nanoR(2nd generation)
•iPod nanoR(1st generation)
•iPhoneR6 Plus
•iPhoneR6
•iPhoneR5S
•iPhoneR5
•iPhoneR4S
•iPhoneR4
•iPhoneR3GS
•iPhoneR3G
•iPhoneR
The iPod touchRmay not respond quickly with
the system in some cases.
Make sure that the iPod
Rfirmware is up-
dated.The Lightning
TMconnector works with iPhone
R5, iPhoneR5S, iPhoneR6, iPhoneR6
Plus, iPod touch
R(5th generation), and iPod
nano
R(7th generation).
The 30-pin connector works with iPhone
R4S,
iPhone
R4, iPhoneR3GS, iPhoneR3G,
iPhone
R, iPod touchR(1st through 4th
generation), iPod classic
R, and iPod nanoR(1st through 6th generation).
USB works with iPhone
R5, iPhoneR4S,
iPhone
R4, iPhoneR3GS, iPhoneR3G,
iPhone
R, iPod touchR(1st through 5th
generation), iPod classi
Rc, and iPod nanoR(1st through 7th generation).
4-76Display screen, heater and air conditioner, and audio system

10iPod menu:
- [Previous List]
- [Playlists]
- [Artists]
- [Songs]
- [Albums]
- [Genres]
- [Composers]
- [Podcasts]
- [Audiobooks]
- [Shuffle]
- [Repeat]
11Repeat mode indicator:
Touch to change the repeat mode.
Mode Screen display
All Track Repeat
All
1 Track Repeat
1 Track
Repeat Off
OFF
iPod player operation
Activation and playing:
Inserting the iPod cable into the connector will
activate the iPod mode.
iPod can also be selected from the audio
sources list and the source bar by touch panel
operation or by pushing.Selecting audio source
Main audio buttons
To play and pause the iPod, touch [Play]/
[Pause] in the iPod menu.
Selecting search method
:
A list of search methods is displayed in the iPod
menu. Touch and select an item to play the iPod
in your preferred settings.
Fast-forwarding/rewinding
:
Push and holdto fast-
forward or rewind the song. Release •TRACK> to play the song at normal speed.
Changing play mode
:
Touch [Shuffle] or [Repeat] from the iPod menu
to select the play mode.
Skipping songs
:
Pushto skip to the next or
previous song.
Even when iPods or iPhones are inserted into
both of the two USB connectors, the system
recognizes only one of the connected iPods or
iPhones at a time.
BLUETOOTH® STREAMING AUDIO
Your vehicle is equipped with Bluetooth®
Streaming Audio.
If you have a compatible Bluetooth® device
with streaming audio (A2DP profile), you can set
up a wireless connection between your
Bluetooth® device and the in-vehicle audio
system. This connection allows you to listen to
the audio from the Bluetooth® device using
your vehicle speakers. It may also allow basic
control of the device for playing and skipping
audio files using the AVRCP Bluetooth® profile.
Not all Bluetooth® devices have the same level
of controls for AVRCP. Please consult the
manual for your Bluetooth® device for more
details.
Wireless LAN (Wi-Fi) and the Bluetooth® func-
tions share the same frequency band (2.4 GHz).
Using the Bluetooth® and the wireless LAN
functions at the same time may slow down or
disconnect the communication and cause unde-
sired noise. It is recommended that you turn off
the wireless LAN (Wi-Fi) when using the
Bluetooth® functions.
4-78Display screen, heater and air conditioner, and audio system