Switch panel INFINITI QX30 2018 User Guide

Touch recessed sensor surface1on the
door handle until the side windows are fully
closed.
NOTE
Make sure you only touch recessed sensor
surface
1.
To interrupt convenience opening: release
the recessed sensor surface
1on the door
handle.
Resetting the side windows
If a side window can no longer be closed fully,
you must reset it.
1. Switch the ignition switch to the ON po- sition.
2. Close the door. 3. Pull the corresponding switch on the door
control panel until the side window is
completely closed
4. Hold the switch for an additional second.
If the side window opens again slightly:
1. Immediately pull the corresponding switch on the door control panel until the side
window is completely closed.
2. Hold the switch for an additional second.
3. If the corresponding side window remains closed after the button has been released,
the side window has been reset correctly.
If this is not the case, repeat the steps
above again.
If the power window automatic function
does not operate properly after performing
the procedure above, have your vehicle
checked. It is recommended you visit an
INFINITI retailer for this service.
1Close
2Open
CAUTION
•Do not place heavy objects on the glass
roof or surrounding area.
•Do not hang from the sunshade or hang
any objects from it. It may cause damage
or deformation to the sunshade.
•Close the sunshade when you leave the
vehicle for extended periods of time to
prevent the inside of the vehicle from
reaching high temperatures.
SUNSHADE OPERATION
The sunshade operates only when the igni-
tion switch is in the ON position.
NPA1478NIC2646
FIXED GLASS ROOF (IF EQUIPPED)
2-76Instruments and controls

COMPARTMENT UNDER TRUNK
FLOOR
Lift the trunk floor to access the underfloor
storage area.
CAUTION
•Turn off the lights when you leave the
vehicle.
•Do not use the lights for extended peri-
ods of time with the engine stopped.
This could result in a discharged battery.
FRONT OVERHEAD CONTROL
PANEL
1Switches the left-hand front reading
light on/off
2Switches the front interior lighting on
3Switches the rear interior lighting on/off
4Switches the right-hand front reading
light on/off
5Switches the front interior lighting/
automatic interior lighting control off
6Switches the automatic interior lighting
control on
Automatic interior lighting control
•To switch on: set the switch to center po-
sition
6.
•To switch off: press switch5.
NIC2673NIC2630
INTERIOR LIGHTS
2-86Instruments and controls

The interior lighting automatically switches
on if you:
•Unlock the vehicle
•Open a door
•Remove the key from the ignition lock.
The interior lighting is activated for a short
time when the key is removed from the igni-
tion lock. You can activate this delayed
switch-off using the vehicle information dis-
play (see "Activating/deactivating the interior
lighting delay" earlier in this section).
REAR READING LIGHTS
(IF EQUIPPED)
1Switches the left hand reading light on/
off
2Switches the right hand reading light on/
off
REAR ROOM LIGHT
(IF EQUIPPED)
The rear room light (without switches) can be
switched on and off using the front overhead
control panel.
VANITY MIRROR LIGHTS
To access the vanity mirror, pull the sun visor
down and flip open the mirror cover.
The vanity mirror light illuminates when the
vanity mirror cover is opened. When the cover
is closed, the light will turn off.
LUGGAGE COMPARTMENT LIGHT
The light illuminates while the lift gate is
opened. When the lift gate is closed, the light
will turn off.
BATTERY SAVER SYSTEM
The interior light will automatically turn off
after a period of time when the ignition
switch has been put in the OFF position. To
turn on the light again, put the ignition switch
in the ON position.
NIC2632SIC3869Z
Instruments and controls2-87

1. Make sure that the windshield wipers areswitched off.
2. Pull the hood lock release lever
1, lo-
cated below the instrument panel on the
driver's side; the hood will spring up
slightly. 3. Push the lever2at the front of the hood,
to the left with your fingertips and raise
the hood.
NDI1603NDI1627
HOOD
Pre-driving checks and adjustments3-15

4 Display screen, heater and air
conditioner, and audio system
Safety precautions.................... .4-2
Center multi function control panel ...........4-2
INFINITI Controller .................. .4-2
Steering wheel mounted controls ..........4-3
USB connection ports ................ .4-4
Starting system .................... .4-4
Touch panel operation ................ .4-4
Operating menu screen ................4-6
Scrolling message or list ................4-7
Selecting item ..................... .4-7
Adjusting volume and settings ............4-7
How to input letters and numbers .........4-8
How to operate display ................4-9
Menu button operation ...............4-10
System status screen ................ .4-11
Items to be set initially ................4-11
Additional system information ...........4-16
RearView monitor (if so equipped) ..........4-17
RearView Monitor system operation .......4-18
How to read the displayed lines ..........4-19
Difference between predicted and actual
distances ....................... .4-19
How to park with predicted course lines .....4-21
Adjusting the screen ................ .4-22
RearView Monitor setting .............4-23
RearView Monitor system limitations ......4-24
System maintenance ................ .4-25Around View Monitor (if so equipped)
.......4-25
Around View Monitor system operation .....4-26
Difference between predicted and actual
distances ....................... .4-30
How to park with predicted course lines .....4-31
How to switch the display .............4-33
Adjusting the screen ................ .4-33
Around View Monitor setting ...........4-34
Around View
®Monitor system limitations . . .4-34
System maintenance ................ .4-37
Sonar function settings (if so equipped) .....4-37
Moving Object Detection (if so equipped) .....4-38
MOD system operation ...............4-39
MOD setting ..................... .4-40
MOD system limitations ...............4-41
MOD malfunction .................. .4-41
System maintenance ................ .4-41
Ventilators ........................ .4-42
Center ventilators .................. .4-42
Side ventilators ................... .4-42
Rear ventilators (if equipped) ............4-42
Heater and air conditioner ...............4-43
Air conditioning system ...............4-44
Automatic climate control (2–zone) .......4-48
Servicing air conditioner ...............4-52
Audio system (if equipped).............. .4-53
Audio operation precautions ............4-53

USB CONNECTION PORTS
The front console compartment contains the
USB connection ports.
1USB/iPod connection port:
Connect to play media from an iPod®,
iPhone® or a USB memory device. When
using INFINITI InTouch Apps with an
iPhone®, connect via a USB cable. Refer
to the device manufacturer’s owner in-
formation regarding the proper use and
care of the device.
CAUTION
•Depending on the size and shape of USB
device, the console lid may not fully
close. Do not force the console lid closed
as this may damage the USB device. NOTE
•Even when iPods® or iPhones® are con-
nected to both of the two USB/iPod ®
connection ports, the system recognizes
only one of the connected iPods® or iP-
hones® at a time.
•Only one of the two connected USB de-
vices can be operated by the voice recog-
nition system.
STARTING SYSTEM
The system starts when the ignition switch is
placed in the ACC or ON position.
Start-up warning (models with
navigation system)
For this system, when the ignition switch is
placed in the ACC or ON position, the
start-up screen is displayed.
Touch [OK] after reading and agreeing to the
message. If you do not agree to the message,
some of Infiniti InTouch
TMfunctions will be
disabled.
NOTE
•Do not keep the INFINITI InTouch system
turned on with the engine stopped. Doing
so may discharge the vehicle battery.
When you use INFINITI InTouch, always
keep the engine running.
•Once you select [Decline] on the start-up
screen, the [OK]/[Decline] screen will not
be displayed for 30 days.
TOUCH PANEL OPERATION
CAUTION
•The glass screen on the liquid crystal dis-
play may break if it is hit with a hard or
sharp object. If the glass screen breaks,
do not touch it. Doing so could result in
an injury.
•To clean the display, use a soft, dry
cloth. If additional cleaning is necessary,
use a small amount of neutral detergent
with a soft cloth. Never use a rough
cloth, alcohol, benzine, thinner or any
kind of solvent or paper towel with a
chemical cleaning agent. They will
scratch or deteriorate the panel.
•Do not splash any liquid such as water or
car fragrance on the display. Contact
with liquid will cause the system to
malfunction.
NAA1628
4-4Display screen, heater and air conditioner, and audio system

WARNING
•The heater and air conditioner operate
only when the engine is running.
•Never leave children or adults who
would normally require the support of
others alone in the vehicle. Pets should
not be left alone either. They could un-
knowingly activate switches or controls
and inadvertently become involved in a
serious accident and injure themselves.
On hot, sunny days, temperatures in a
closed vehicle could quickly become high
enough to cause severe or possibly fatal
injuries to people or animals.
•Do not use the recirculation mode for
long periods as it may cause the interior
air to become stale and the windows to
fog up.
•Do not adjust the heating and air condi-
tioning controls while driving so that full
attention may be given to vehicle
operation.
The heater and air conditioner operate when
the engine is running. The air blower will op-
erate even if the engine is turned off and the
ignition switch is in the ON position. NOTE
•Condensation forms inside the air condi-
tioning unit when the air conditioner (if
equipped) is running, and is safely dis-
charged underneath your vehicle.
Traces of water on the ground are there-
fore normal.
•Odors from inside and outside the vehicle
can build up in the air conditioner unit.
Odor can enter the passenger compart-
ment through the ventilators.
When parking, set the heater and air con-
ditioner controls to turn off air recircula-
tion to allow fresh air into the passenger
compartment. This should help reduce
odors inside the vehicle.
Observe the settings recommended on the
following pages. The windows could other-
wise mist up. To prevent the windows from
misting up
•Switch off climate control only briefly.
•Switch on air-recirculation mode only
briefly.
•Switch on the cooling with air dehumidifi-
cation function.
•Switch on the windshield demisting func-
tion briefly, if required. The air-conditioning system/automatic cli-
mate control regulates the temperature and
the humidity of the vehicle interior and filters
undesirable substances from the air.
The air-conditioning system/automatic cli-
mate control can only be operated when the
engine is running. Optimum operation is only
achieved with the side windows closed.
Always keep the ventilation flaps behind the
side panelling clear. Otherwise the vehicle will
not be ventilated correctly.
NOTE
•Ventilate the vehicle for a brief period dur-
ing warm weather. This will speed up the
cooling process and the desired interior
temperature will be reached more quickly.
•The integrated filter filters out most par-
ticles of dust and soot and completely fil-
ters out pollen. With automatic climate
control, gaseous pollutants and odors will
also be reduced. A clogged filter reduces
the amount of air supplied to the vehicle
interior. For this reason, you should always
observe the interval for replacing the filter,
which is specified in the Service Booklet.
As this depends on environmental condi-
tions, for example heavy air pollution, the
interval may be shorter than stated in the
Service Booklet.
HEATER AND AIR CONDITIONER
Display screen, heater and air conditioner, and audio system4-43

5[USB1]/[USB2]:
Touch to switch to the other connected
USB memory device.
6Album artwork (if equipped):
An image of the CD cover is displayed
when available.
7Track number:
This indicates the track number and the
total number of tracks.
8[]/[]:
Touch to play or pause the track.
9USB menu:
USB menu items are displayed. Touch an
icon to display the list or to change the
setting.
- [Folder/Track]
- [Artists]
- [Albums]
- [Previous List]
- [Scan]
- [Play Mode]
10Play mode indicator:
This indicates the current play mode.
Touch to change the play mode.
Mode Screen display
All Track Repeat
All
1 Folder Repeat
1 Folder
1 Track Repeat
1 Track
All Random
All
1 Folder Random
1 Folder
11Folder number:
This indicates the folder, artist or album
number and the total number of folders/
lists.
USB memory device player
operation
Activation and playing:
USB memory device mode can also be acti-
vated from the audio source list and the audio
source bar by the touch panel operation or by
pushing .
Selecting audio source page 4-65
Main audio buttons page 4-64
To play the USB memory device touch [
],
and to pause the USB memory touch []
on the USB operation screen. Selecting play list:
Select a play list by touching an icon in the
USB menu.
•Folder/Track (List)
•Artist (List)
•Album (List)
•Previous List
Skipping tracks/folders:
Push to skip to the next
or previous track.
To skip to the next or previous folder, Push
.
Fast-forwarding/rewinding:
Push and hold to fast-
forward or rewind the track. Release •CAT•TRACK> to play the track at normal
speed.
Scanning:
Touch [Scan] on the display to scan the
tracks in the USB memory device. While
scanning, the USB memory device will play
the first 10 seconds of each track and move
on to the next track. Touching [Scan] again
within the 10 seconds will stop scanning.
4-74Display screen, heater and air conditioner, and audio system

The sonar function is deactivated for the rear
area when you establish an electrical connec-
tion between your vehicle and a trailer.
RANGE OF THE SENSORS
The sonar function does not take into ac-
count obstacles located:
•Below the detection range, e.g. persons,
animals or objects.
•Above the detection range, e.g. overhang-
ing loads, tail sections or loading ramps of
goods vehicles.
SONAR FUNCTION OFF SWITCH
The sonar function OFF switch2on the
lower side of the instrument panel allows the
driver to turn the sonar function on and off.
To turn the sonar function system on and off,
the ignition switch must be in the ON posi-
tion. The indicator light
1on the switch will
illuminate when the system is turned off.
The sonar function will turn on automatically
when the ignition switch is turned from the
OFF position to the ON position.
NIC2635
5-82Starting and driving

Self-test feature
The ABS includes electronic sensors, electric
pumps, hydraulic solenoids and a computer.
The computer has a built-in diagnostic fea-
ture that tests the system each time you start
the engine and move the vehicle at a low
speed in forward or reverse. When the self-
test occurs, you may hear a “clunk” noise
and/or feel a pulsation in the brake pedal.
This is normal and does not indicate a mal-
function. If the computer senses a malfunc-
tion, it switches the ABS off and illuminates
the ABS warning light on the instrument
panel. The brake system then operates nor-
mally, but without anti-lock assistance. If the
ABS warning light illuminates during the self-
test or while driving, have the vehicle
checked. It is recommended you visit an
INFINITI retailer for this service.
Normal operation
The ABS operates at speeds above 3 to 6
MPH (5 to 10 km/h). The speed varies ac-
cording to road conditions.
When the ABS senses that one or more
wheels are close to locking up, the actuator
rapidly applies and releases hydraulic pres-
sure. This action is similar to pumping the
brakes very quickly. You may feel a pulsation
in the brake pedal and hear a noise from
under the hood or feel a vibration from the
actuator when it is operating. This is normal
and indicates that the ABS is operating prop-
erly. However, the pulsation may indicate
that road conditions are hazardous and extra
care is required while driving.The Vehicle Dynamic Control (VDC) system
uses various sensors to monitor driver inputs
and vehicle motion. Under certain driving
conditions, the VDC system helps to perform
the following functions.
•Controls brake pressure to reduce wheel
slip on one slipping drive wheel so power is
transferred to a non slipping drive wheel
on the same axle.
•Controls brake pressure and engine output
to reduce drive wheel slip based on vehicle
speed (traction control function).
•Controls brake pressure at individual
wheels and engine output to help the
driver maintain control of the vehicle in the
following conditions: – understeer (vehicle tends to not follow the steered path despite increased
steering input)
– oversteer (vehicle tends to spin due to certain road or driving conditions).
The VDC system can help the driver to main-
tain control of the vehicle, but it cannot pre-
vent loss of vehicle control in all driving situ-
ations.
VEHICLE DYNAMIC CONTROL (VDC)
SYSTEM
Starting and driving5-93