sensor ISUZU AXIOM 2002 Service Repair Manual
[x] Cancel search | Manufacturer: ISUZU, Model Year: 2002, Model line: AXIOM, Model: ISUZU AXIOM 2002Pages: 2100, PDF Size: 19.35 MB
Page 1226 of 2100
6E±259
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
DTC P0300 ± Engine Misfire Detected
StepNo Ye s Value(s) Action
171. Perform the ªInjector Coil/Balance Testº.
2. If a problem is found, replace faulty injector(s) as
necessary.
Did any of the injectors require replacement?
ÐVerify repairGo to Step 18
181. Check for an engine mechanical problem. Refer to
Engine Mechanical Diagnosis to diagnose the
following conditions:
A faulty or incorrect camshaft
Leaking or sticky valves or rings
Excessive valve deposits
Weak valve springs
Incorrect valve timing
A leaking head gasket
A loose or broken motor mount
2. If a problem is found, repair as necessary.
Was a basic engine mechanical problem found and
repaired?
ÐVerify repairGo to Step 19
191. Check for a transmission TCC problem. Refer to
4L30-E Automatic Transmission Diagnosis.
2. If a problem is found, repair the transmission as
necessary. Refer to
4L30-E Automatic
Transmission Unit Repair
.
Was a transmission problem found and repaired?
ÐVerify repair Go to Step 20
20Replace the MAF sensor.
Is the action complete?
ÐVerify repairÐ
Page 1227 of 2100
6E±260
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Diagnostic Trouble Code (DTC) P0301 Cylinder Misfire Detected
Circuit Description
Misfire is monitored as a function of the combustion
quality (CQ) signals generated from the ignition current
sense system. Combustion signals represent the degree
of combustion in each cylinder. Misfire is detected when
the combustion signal is below a predetermined value.
This DTC P0301 will determine if the No.1 cylinder misfire
is occurring by monitoring the Combustion Quality.
Conditions for Setting the DTC
None of the following DTCs occur: TP sensor, MAF
sensor, vehicle speed sensor, ECT sensor.
The engine speed is between 600 and 6250 RPM.
The system voltage is between 11 and 16 volts.
The ECT indicates an engine temperature between
±7C (28F) and 110C (230F).
The throttle angle is steady and throttle change less
than 2% per 125 milliseconds.
Action Taken When the DTC Sets
The PCM will ON the MIL after second trip with
detected the fault.
If the misfire is severe enough to cause possible
catalyst damage, the PCM will flash the MIL for as long
as the misfire remains at catalyst damaging levels.
The PCM will store conditions which were present
when the DTC was set as Freeze Frame and in the
Failure Records data.
Conditions for Clearing the MIL/DTC
The PCM will turn the MIL ªOFFº on the third
consecutive ignition cycle in which the diagnostic has
been run and the fault condition is no longer present.
A history DTC P0301 will clear after 40 consecutive
ignition cycles occur without a fault.
DTC P0301 can be cleared by using the Tech 2 ªClear
Infoº function or by disconnecting the PCM battery
feed.
Diagnostic Aids
Check for the following conditions:
System grounds ± Ensure all connections are clean
and properly tightened.
Injector ± Perform the injector coil/balance test to
locate a faulty injector that contributes to a lean
condition on the affected cylinder. In addition to the
above test, check the condition of the injector O-ring.
Faulty spark plug ± Check for a cracked insulator,
carbon tracking, incorrect gap, and worn electrodes.
Damaged or faulty ignition coil ± Check for cracks or
other damage.
Substitute a known good coil ± Swap the ignition coils
and retest. If the misfire follows the coil, replace the
ignition coil.
DTC P0301 ± Cylinder Misfire Detected
StepActionValue(s)Ye sNo
1Was the ªOn-Board Diagnostic (OBD) System Checkº
performed?
ÐGo to Step 2
Go to OBD
System
Check
21. Start the engine. Run the engine at idle.
2. Review and record Tech 2 Freeze Frame data.
3. Monitor ªMisfire Cur. #1º on the Tech 2.
Is ªMisfire Cur. #1º increasing (indicating a misfire
currently occurring)?
ÐGo to Step 4Go to Step 3
3Monitor ªMisfire Hist. #1º while operating the vehicle to
duplicate the conditions present when the DTC was set
(as defined by the Freeze Frame data recorded in Step
2).
Is ªMisfire Hist. #1º increasing (indicating a misfire
currently occurring)?
ÐGo to Step 4
Refer to
Diagnostic
Aids
41. Visually and physically inspect the vacuum hoses
for splits, kinks, and improper connections. Also,
inspect the intake manifold for a vacuum leak.
2. If a problem is found, repair it as necessary.
Did the inspection reveal a problem?
ÐVerify repairGo to Step 5
51. Install a spark tester at the spark plug end of the
cylinder #1 ignition coil.
2. Crank the engine while observing the spark tester.
A crisp, blue spark should be observed.
Is adequate spark present?
ÐGo to Step 8Go to Step 6
Page 1229 of 2100
6E±262
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Diagnostic Trouble Code (DTC) P0302 Cylinder Misfire Detected
Circuit Description
Misfire is monitored as a function of the combustion
quality (CQ) signals generated from the ignition current
sense system. Combustion signals represent the degree
of combustion in each cylinder. Misfire is detected when
the combustion signal is below a predetermined value.
This DTC P0302 will determine if the No.2 cylinder misfire
is occurring by monitoring the Combustion Quality.
Conditions for Setting the DTC
None of the following DTCs occur: TP sensor, MAF
sensor, vehicle speed sensor, ECT sensor.
The engine speed is between 600 and 6250 RPM.
The system voltage is between 11 and 16 volts.
The ECT indicates an engine temperature between
±7C (28F) and 110C (230F).
The throttle angle is steady and throttle change less
than 2% per 125 milliseconds.
Action Taken When the DTC Sets
The PCM will illuminate the malfunction indicator lamp
(MIL) the first time the fault is detected.
If the misfire is severe enough to cause possible
catalyst damage, the PCM will flash the MIL for as long
as the misfire remains at catalyst damaging levels.
The PCM will store conditions which were present
when the DTC was set as Freeze Frame and in the
Failure Records data.
Conditions for Clearing the MIL/DTC
The PCM will turn the MIL ªOFFº on the third
consecutive ignition cycle in which the diagnostic has
been run and the fault condition is no longer present.
A history DTC P0302 will clear after 40 consecutive
ignition cycles occur without a fault.
DTC P0302 can be cleared by using the Tech 2 ªClear
Infoº function or by disconnecting the PCM battery
feed.
Diagnostic Aids
Check for the following conditions:
System grounds ± Ensure all connections are clean
and properly tightened.
Injector ± Perform the injector coil/balance test to
locate a faulty injector that contributes to a lean
condition on the affected cylinder. In addition to the
above test, check the condition of the injector O-ring.
Faulty spark plug ± Check for a cracked insulator,
carbon tracking, incorrect gap, and worn electrodes.
Damaged or faulty ignition coil ± Check for cracks,
carbon tracking or other damage.
Substitute a known good coil ± Swap the ignition coils
and retest. If the misfire follows the coil, replace the
ignition coil.
DTC P0302 ± Cylinder Misfire Detected
StepActionValue(s)Ye sNo
1Was the ªOn-Board Diagnostic (OBD) System Checkº
performed?
ÐGo to Step 2
Go to OBD
System
Check
21. Start the engine. Run the engine at idle.
2. Review and record Tech 2 Freeze Frame data.
3. Monitor ªMisfire Cur. #2º on the Tech 2.
Is ªMisfire Cur. #2º increasing (indicating a misfire
currently occurring)?
ÐGo to Step 4Go to Step 3
3Monitor ªMisfire Hist. #2º while operating the vehicle to
duplicate the conditions present when the DTC was set
(as defined by the Freeze Frame data recorded in Step
2).
Is ªMisfire Hist. #2º increasing (indicating a misfire
currently occurring)?
ÐGo to Step 4
Refer to
Diagnostic
Aids
41. Visually and physically inspect the vacuum hoses
for splits, kinks, and improper connections. Also,
inspect the intake manifold for a vacuum leak.
2. If a problem is found, repair it as necessary.
Did the inspection reveal a problem?
ÐVerify repairGo to Step 5
51. Install a spark tester at the spark plug end of the
cylinder #2 ignition coil.
2. Crank the engine while observing the spark tester.
A crisp, blue spark should be observed.
Is adequate spark present?
ÐGo to Step 8Go to Step 6
Page 1231 of 2100
6E±264
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Diagnostic Trouble Code (DTC) P0303 Cylinder Misfire Detected
Circuit Description
Misfire is monitored as a function of the combustion
quality (CQ) signals generated from the ignition current
sense system. Combustion signals represent the degree
of combustion in each cylinder. Misfire is detected when
the combustion signal is below a predetermined value.
This DTC P0303 will determine if the No.3 cylinder misfire
is occurring by monitoring the Combustion Quality.
Conditions for Setting the DTC
None of the following DTCs occur: TP sensor, MAF
sensor, vehicle speed sensor, ECT sensor.
The engine speed is between 600 and 6250 RPM.
The system voltage is between 11 and 16 volts.
The ECT indicates an engine temperature between
±7C (28F) and 110C (230F).
The throttle angle is steady and throttle change less
than 2% per 125 milliseconds.
Action Taken When the DTC Sets
The PCM will ON the MIL after second trip with
detected the fault.
If the misfire is severe enough to cause possible
catalyst damage, the PCM will flash the MIL for as long
as the misfire remains at catalyst damaging levels.
The PCM will store conditions which were present
when the DTC was set as Freeze Frame and in the
Failure Records data.
Conditions for Clearing the MIL/DTC
The PCM will turn the MIL ªOFFº on the third
consecutive ignition cycle in which the diagnostic has
been run and the fault condition is no longer present.
A history DTC P0303 will clear after 40 consecutive
ignition cycles occur without a fault.
DTC P0303 can be cleared by using the Tech 2 ªClear
Infoº function or by disconnecting the PCM battery
feed.
Diagnostic Aids
Check for the following conditions:
System grounds ± Ensure all connections are clean
and properly tightened.
Injector Ð Perform the injector coil/balance test to
locate a faulty injector that contributes to a lean
condition on the affected cylinder. In addition to the
above test, check the condition of the injector O-ring.
Faulty spark plug ± Check for a cracked insulator,
carbon tracking, incorrect gap, and worn electrodes.
Damaged or faulty ignition coil ± Check for cracks,
carbon tracking or other damage.
Substitute a known good coil ± Swap the ignition coils
and retest. If the misfire follows the coil, replace the
ignition coil.
DTC P0303 ± Cylinder Misfire Detected
StepActionValue(s)Ye sNo
1Was the ªOn-Board Diagnostic (OBD) System Checkº
performed?
ÐGo to Step 2
Go to OBD
System
Check
21. Start the engine. Run the engine at idle.
2. Review and record Tech 2 Freeze Frame data.
3. Monitor ªMisfire Cur. #3º on the Tech 2.
Is ªMisfire Cur. #3º increasing (indicating a misfire
currently occurring)?
ÐGo to Step 4Go to Step 3
3Monitor ªMisfire Hist. #3º while operating the vehicle to
duplicate the conditions present when the DTC was set
(as defined by the Freeze Frame data recorded in Step
2).
Is ªMisfire Hist. #3º increasing (indicating a misfire
currently occurring)?
ÐGo to Step 4
Refer to
Diagnostic
Aids
41. Visually and physically inspect the vacuum hoses
for splits, kinks, and improper connections. Also,
inspect the intake manifold for a vacuum leak.
2. If a problem is found, repair it as necessary.
Did the inspection reveal a problem?
ÐVerify repairGo to Step 5
51. Install a spark tester at the spark plug end of the
cylinder #3 ignition coil.
2. Crank the engine while observing the spark tester.
A crisp, blue spark should be observed.
Is adequate spark present?
ÐGo to Step 8Go to Step 6
Page 1233 of 2100
6E±266
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Diagnostic Trouble Code (DTC) P0304 Cylinder Misfire Detected
Circuit Description
Misfire is monitored as a function of the combustion
quality (CQ) signals generated from the ignition current
sense system. Combustion signals represent the degree
of combustion in each cylinder. Misfire is detected when
the combustion signal is below a predetermined value.
This DTC P0304 will determine if the No.4 cylinder misfire
is occurring by monitoring the Combustion Quality.
Conditions for Setting the DTC
None of the following DTCs occur: TP sensor, MAF
sensor, vehicle speed sensor, ECT sensor.
The engine speed is between 600 and 6250 RPM.
The system voltage is between 11 and 16 volts.
The ECT indicates an engine temperature between
±7C (28F) and 110C (230F).
The throttle angle is steady and throttle change less
than 2% per 125 milliseconds.
Action Taken When the DTC Sets
The PCM will ON the MIL after second trip with
detected the fault.
If the misfire is severe enough to cause possible
catalyst damage, the PCM will flash the MIL for as long
as the misfire remains at catalyst damaging levels.
The PCM will store conditions which were present
when the DTC was set as Freeze Frame and in the
Failure Records data.
Conditions for Clearing the MIL/DTC
The PCM will turn the MIL ªOFFº on the third
consecutive ignition cycle in which the diagnostic has
been run and the fault condition is no longer present.
A history DTC P0304 will clear after 40 consecutive
ignition cycles occur without a fault.
DTC P0304 can be cleared by using the Tech 2 ªClear
Infoº function or by disconnecting the PCM battery
feed.
Diagnostic Aids
Check for the following conditions:
System grounds ± Ensure all connections are clean
and properly tightened.
Injector ± Perform the injector coil/balance test to
locate a faulty injector that contributes to a lean
condition on the affected cylinder. In addition to the
above test, check the condition of the injector O-ring.
Faulty spark plug ± Check for a cracked insulator,
carbon tracking, incorrect gap, and worn electrodes.
Damaged or faulty ignition coil ± Check for cracks,
carbon tracking or other damage.
Substitute a known good coil ± Swap the ignition coils
and retest. If the misfire follows the coil, replace the
ignition coil.
DTC P0304 ± Cylinder Misfire Detected
StepActionValue(s)Ye sNo
1Was the ªOn-Board Diagnostic (OBD) System Checkº
performed?
ÐGo to Step 2
Go to OBD
System
Check
21. Start the engine. Run the engine at idle.
2. Review and record Tech 2 Freeze Frame data.
3. Monitor ªMisfire Cur. #4º on the Tech 2.
Is ªMisfire Cur. #4º increasing (indicating a misfire
currently occurring)?
ÐGo to Step 4Go to Step 3
3Monitor ªMisfire Hist. #4º while operating the vehicle to
duplicate the conditions present when the DTC was set
(as defined by the Freeze Frame data recorded in Step
2).
Is ªMisfire Hist. #4º increasing (indicating a misfire
currently occurring)?
ÐGo to Step 4
Refer to
Diagnostic
Aids
41. Visually and physically inspect the vacuum hoses
for splits, kinks, and improper connections. Also,
inspect the intake manifold for a vacuum leak.
2. If a problem is found, repair it as necessary.
Did the inspection reveal a problem?
ÐVerify repairGo to Step 5
51. Install a spark tester at the spark plug end of the
cylinder #4 ignition wire.
2. Crank the engine while observing the spark tester.
A crisp, blue spark should be observed.
Is adequate spark present?
ÐGo to Step 8Go to Step 6
Page 1235 of 2100
6E±268
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Diagnostic Trouble Code (DTC) P0305 Cylinder Misfire Detected
Circuit Description
Misfire is monitored as a function of the combustion
quality (CQ) signals generated from the ignition current
sense system. Combustion signals represent the degree
of combustion in each cylinder. Misfire is detected when
the combustion signal is below a predetermined value.
This DTC P0305 will determine if the No.5 cylinder misfire
is occurring by monitoring the Combustion Quality.
Conditions for Setting the DTC
None of the following DTCs occur: TP sensor, MAF
sensor,vehicle speed sensor, ECT sensor.
The engine speed is between 600 and 6250 RPM.
The system voltage is between 11 and 16 volts.
The ECT indicates an engine temperature between
±7C (28F) and 110C (230F).
The throttle angle is steady and throttle change less
than 2% per 125 milliseconds.
Action Taken When the DTC Sets
The PCM will ON the MIL after second trip with
detected the fault.
If the misfire is severe enough to cause possible
catalyst damage, the PCM will flash the MIL for as long
as the misfire remains at catalyst damaging levels.
The PCM will store conditions which were present
when the DTC was set as Freeze Frame and in the
Failure Records data.
Conditions for Clearing the MIL/DTC
The PCM will turn the MIL ªOFFº on the third
consecutive ignition cycle in which the diagnostic has
been run and the fault condition is no longer present.
A history DTC P0305 will clear after 40 consecutive
ignition cycles occur without a fault.
DTC P0305 can be cleared by using the Tech 2 ªClear
Infoº function or by disconnecting the PCM battery
feed.
Diagnostic Aids
Check for the following conditions:
System grounds ± Ensure all connections are clean
and properly tightened.
Injector ± Perform the injector coil/balance test to
locate a faulty injector that contributes to a lean
condition on the affected cylinder. In addition to the
above test, check the condition of the injector O-ring.
Faulty spark plug ± Check for a cracked insulator,
carbon tracking, incorrect gap, and worn electrodes.
Damaged or faulty ignition coil ± Check for cracks,
carbon tracking or other damage.
Substitute a known good coil ± Swap the ignition coils
and retest. If the misfire follows the coil, replace the
ignition coil.
DTC P0305 ± Cylinder Misfire Detected
StepActionValue(s)Ye sNo
1Was the ªOn-Board Diagnostic (OBD) System Checkº
performed?
ÐGo to Step 2
Go to OBD
System
Check
21. Start the engine. Run the engine at idle.
2. Review and record Tech 2 Freeze Frame data.
3. Monitor ªMisfire Cur. #5º on the Tech 2.
Is ªMisfire Cur. #5º increasing (indicating a misfire
currently occurring)?
ÐGo to Step 4Go to Step 3
3Monitor ªMisfire Hist. #5º while operating the vehicle to
duplicate the conditions present when the DTC was set
(as defined by the Freeze Frame data recorded in Step
2).
Is ªMisfire Hist. #5º increasing (indicating a misfire
currently occurring)?
ÐGo to Step 4
Refer to
Diagnostic
Aids
41. Visually and physically inspect the vacuum hoses
for splits, kinks, and improper connections. Also,
inspect the intake manifold for a vacuum leak.
2. If a problem is found, repair it as necessary.
Did the inspection reveal a problem?
ÐVerify repair Go to Step 5
51. Install a spark tester at the spark plug end of the
cylinder #5 ignition wire.
2. Crank the engine while observing the spark tester.
A crisp, blue spark should be observed.
Is adequate spark present?
ÐGo to Step 8Go to Step 6
Page 1237 of 2100
6E±270
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Diagnostic Trouble Code (DTC) P0306 Cylinder Misfire Detected
Circuit Description
Misfire is monitored as a function of the combustion
quality (CQ) signals generated from the ignition current
sense system. Combustion signals represent the degree
of combustion in each cylinder. Misfire is detected when
the combustion signal is below a predetermined value.
This DTC P0306 will determine if the No.6 cylinder misfire
is occurring by monitoring the Combustion Quality.
Conditions for Setting the DTC
None of the following occur: TP sensor, MAF sensor,
vehicle speed sensor, ECT sensor.
The engine speed is between 600 and 6250 RPM.
The system voltage is between 11 and 16 volts.
The ECT indicates an engine temperature between
±7C (28F) and 110C (230F).
The throttle angle is steady and throttle change less
than 2% per 125 milliseconds.
Action Taken When the DTC Sets
The PCM will ON the MIL after second trip with
detected the fault.
If the misfire is severe enough to cause possible
catalyst damage, the PCM will flash the MIL for as long
as the misfire remains at catalyst damaging levels.
The PCM will store conditions which were present
when the DTC was set as Freeze Frame and in the
Failure Records data.
Conditions for Clearing the MIL/DTC
The PCM will turn the MIL ªOFFº on the third
consecutive ignition cycle in which the diagnostic has
been run and the fault condition is no longer present.
A history DTC P0306 will clear after 40 consecutive
ignition cycles occur without a fault.
DTC P0306 can be cleared by using the Tech 2 ªClear
Infoº function or by disconnecting the PCM battery
feed.
Diagnostic Aids
Check for the following conditions:
System grounds ± Ensure all connections are clean
and properly tightened.
Injector ± Perform the injector coil/balance test to
locate a faulty injector that contributes to a lean
condition on the affected cylinder. In addition to the
above test, check the condition of the injector O-ring.
Faulty spark plug ± Check for a cracked insulator,
carbon tracking, incorrect gap, and worn electrodes.
Damaged or faulty ignition coil ± Check for cracks or
other damage.
Substitute a known good coil ± Swap the ignition coils
and retest. If the misfire follows the coil, replace the
ignition coil.
DTC P0306 ± Cylinder Misfire Detected
StepActionValue(s)Ye sNo
1Was the ªOn-Board Diagnostic (OBD) System Checkº
performed?
ÐGo to Step 2
Go to OBD
System
Check
21. Start the engine. Run the engine at idle.
2. Review and record Tech 2 Freeze Frame data.
3. Monitor ªMisfire Cur. #6º on the Tech 2.
Is ªMisfire Cur. #6º increasing (indicating a misfire
currently occurring)?
ÐGo to Step 4Go to Step 3
3Monitor ªMisfire Hist. #6º while operating the vehicle to
duplicate the conditions present when the DTC was set
(as defined by the Freeze Frame data recorded in Step
2).
Is ªMisfire Hist. #6º increasing (indicating a misfire
currently occurring)?
ÐGo to Step 4
Refer to
Diagnostic
Aids
41. Visually and physically inspect the vacuum hoses
for splits, kinks, and improper connections. Also,
inspect the intake manifold for a vacuum leak.
2. If a problem is found, repair it as necessary.
Did the inspection reveal a problem?
ÐVerify repairGo to Step 5
51. Install a spark tester at the spark plug end of the
cylinder #6 ignition wire.
2. Crank the engine while observing the spark tester.
A crisp, blue spark should be observed.
Is adequate spark present?
ÐGo to Step 8Go to Step 6
Page 1240 of 2100
6E±273
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
If the harness appears to be OK, observe the Knock
Present, Knock Sensor Noise Channel display on
the Tech 2 while moving connectors and wiring
harnesses related to the sensor.
A change in the display will indicate the location of
the fault.If DTC P0325 cannot be duplicated, the information
included in the Failure Records data can be useful in
determined vehicle mileage since the DTC was last
set.
If it is determined that the DTC occurs intermittently,
performing the DTC P0325 Diagnostic Chart may
isolate the cause of the fault.
DTC P0325 - ION Sensing Module Knock Intensity Circuit Fault
StepActionValue(s)Ye sNo
1Was the ªOn-Board (OBD) System Checkº performed?
ÐGo to Step 2
Go to OBD
System
Check
21. Ignition ªONº, engine ªOFFº.
2. Review and record Tech 2 Failure Records data.
3. Operate the vehicle within Failure Records
conditions as noted.
4. Using a Tech 2, monitor ªDTCº info for DTC P0325.
Does the Tech 2 indicate DTC P0325 failed this
ignition?
ÐGo to Step 3
Refer to
Diagnostic
Aids
31. Ignition ªOFFº.
2. Disconnect the ION sensing module.
3. Disconnect the PCM.
Is the action complete?
ÐGo to Step 4Ð
4Check the ION sensing harness between the PCM
(F68) and ION sensing module circuit (RED Wire) at
the KI line harness connector.
Was a problem found?
ÐVerify repairGo to Step 5
51. Disconnect the ignition coil.
Is the action complete?
ÐGo to Step 6Ð
6Check the ION sensing harness for open or short circuit
between the ignition coil and ION sensing module
circuit at the harness connector.
Was a problem found?
ÐVerify repairGo to Step 7
7Check the following items;
1. Ignition coil and ignition coil circuit.
2. Ignition coil ground circuit for a poor connection.
3. If a problem is found, repair wiring harness as
necessary.
Was a problem found?
ÐVerify repairGo to Step 8
8Replace the Ignition coil.
Is the action complete?
ÐVerify repairGo to Step 9
9Check the following items;
1. ION sensing module ground circuit for a poor
connection.
2. If a problem is found, repair wiring harness as
necessary.
Was a problem found?
ÐGo to Step 10Go to Step 11
10Repair wiring harness.
Is the action complete?
ÐVerify repairGo to Step 11
Page 1241 of 2100
6E±274
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
DTC P0325 - ION Sensing Module Knock Intensity Circuit Fault
StepNo Ye s Value(s) Action
11Replace the ION Sensing module.
Is the action complete?
ÐVerify repairGo to Step 12
12Replace the PCM.
IMPORTANT:The replacement PCM must be
programmed.
Refer to
ON-Vehicle Service in Power Control Module
and Sensors for procedures.
And also refer to latest Service Bulletin. Check to see if
the latest software is released or not .And then Down
Load the LATEST PROGRAMMED SOFTWARE to
the replacement PCM.
Is the action complete?
ÐVerify repairÐ
Page 1242 of 2100
6E±275
6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Diagnostic Trouble Code (DTC) P0336 58X Reference Signal Circuit
060R200066
Circuit Description
The 58X reference signal is produced by the crankshaft
position (CKP) sensor. During one crankshaft revolution,
58 crankshaft pulses will be produced. The powertrain
control module (PCM) uses the 58X reference signal to
calculate engine RPM and crankshaft position. The PCM
constantly monitors the number of pulses on the 58X
reference circuit. If the PCM receives an incorrect
number of pulses on the 58X reference circuit, DTC
P0336 will set.
Conditions for Setting the DTC
Engine is running.
Extra or missing pulse is detected between
consecutive 58X reference pulses.
Above condition is detected in 10 of 100 crankshaft
rotations.
Action Taken When the DTC Sets
The PCM will illuminate the malfunction indicator lamp
(MIL) after the second consecutive trip in which the
fault is detected.
The PCM will store conditions which were present
when the DTC was set as Freeze Frame and in the
Failure Records data.
Conditions for Clearing the MIL/DTC
The PCM will turn the MIL ªOFFº on the third
consecutive trip cycle during which the diagnostic has
been run and the fault condition is no longer present.
A history DTC P0336 will clear after 40 consecutive
warm±up cycles have occurred without a fault.
DTC P0336 can be cleared by using the Tech 2 ªClear
Infoº function or by disconnecting the PCM battery
feed.