oil JAGUAR XFR 2010 1.G Owners Manual

Engine - V8 S/C 5.0L Petrol - Crankshaft Rear Seal
Removal and Installation

Special Tool(s)






Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 12-May-2014

1. Refer to: Flexplate (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).

2. 303-1442
Rear Crankshaft Seal Installer JLR-303-1622
Alignment Tool, Engine Rear Oil Seal

7.
















8.
9.
10. Torque: 25 Nm

















NOTE: Tighten the bolts in the indicated sequence.

Torque: 12 Nm













CAUTIONS:


If a new cylinder head has been installed then new
tappets must be installed.


If the cylinder head is being removed without a new
component being installed, the tappets must be installed in
their original positions.
Lubricate the valve tappets with clean engine oil.







Torque: 10 Nm

7. Torque: 25 Nm 8. Torque: 12 Nm 9. CAUTIONS:


If a new cylinder head has been installed then new
tappets must be installed.


If the cylinder head is being removed without a new
component being installed, the tappets must be installed in
their original positions.
Lubricate the valve tappets with clean engine oil.

10.

























11. NOTE: Install a new gasket.

























CAUTION: A new O-ring seal is to be installed.


NOTE: Install a new engine oil filter.

Engine - V8 S/C 5.0L Petrol - Oil Cooler
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 19-Nov-2013

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


2. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.

3. Refer to: Cooling System Partial Draining, Filling and Bleeding - V8 S/C 5.0L Petrol (303-03C Engine Cooling - V8 5.0L Petrol/V8 S/C 5.0L Petrol, General Procedures).

4. Refer to: Supercharger (303-12D Intake Air Distribution and Filtering - V8 S/C 5.0L Petrol, Removal and Installation).

5.
6. www.JagDocs.com

7. CAUTIONS:


Be prepared to collect escaping oil.


Be prepared to collect escaping coolant.

Torque: 13 Nm









8. CAUTION: Make sure that these components are
installed to the noted removal position.


NOTE: Install a new gasket.

Engine - V8 S/C 5.0L Petrol - Oil Filter Element
Removal and Installation

Removal Published: 11-May-2011


NOTE: Some variation in the illustrations may occur, but the essential information is always correct.

1. Refer to: Engine Cover - V8 5.0L Petrol/V8 S/C 5.0L Petrol (501-05 Interior Trim and Ornamentation, Removal and Installation).

2.
Allow the engine oil to drain from the oil filter
element housing for two minutes.















3.
4.

3. Check and top-up the engine oil.

4. Start and run the engine.

5. Refer to: Engine Cover - V8 5.0L Petrol/V8 S/C 5.0L Petrol (501-05 Interior Trim and Ornamentation, Removal and Installation). Installation

Engine - V8 S/C 5.0L Petrol - Oil Pan
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


2. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.

3. Refer to: Engine Oil Level Sensor (303-14D Electronic Engine Controls - V8 S/C 5.0L Petrol, Removal and Installation).

4. www.JagDocs.com

Installation
1. CAUTIONS:


Use only a plastic scraper when removing the sealing
material.


Use lint free cloth.


Make sure that the mating faces are clean and free of
corrosion and foreign material.

Apply RTV sealant WSE-M4G323-A6 (Loctite 5901G)
to the areas shown, and tighten the bolts within 7
minutes.
Apply a bead of sealant, 2.5 mm diameter, to the
area indicated.








2. NOTE: Tighten the bolts in the sequence shown.
Torque: 12 Nm
















3. Refer to: Engine Oil Level Sensor (303-14D Electronic Engine Controls - V8 S/C 5.0L Petrol, Removal and Installation).