buttons JEEP GRAND CHEROKEE 2011 Owner handbook (in English)

WARNING!
Do not adjust the steering column while driv-
ing. Adjusting the steering column while driv-
ing or driving with the steering column un-
locked, could cause the driver to lose control
of the vehicle. Be sure the steering column is
locked before driving your vehicle. Failure to
follow this warning may result in serious injury
or death.
HEATED STEERING WHEEL —
IF EQUIPPED
The steering wheel contains a heating element
that helps warm your hands in cold weather.
The heated steering wheel has only one tem-
perature setting. Once the heated steering
wheel has been turned on it will operate for
approximately 58 to 70 minutes before auto-
matically shutting off. The heated steering
wheel can shut off early or may not turn on
when the steering wheel is already warm.
The heated steering wheel switch is located on
the switch bank below the climate controls.Press the switch to turn
on the heated steering
wheel. The light on the
switch will illuminate to
indicate the steering
wheel heater is on.
Pressing the switch a
second time will turn off
the heated steering
wheel and light indica-
tor.
NOTE:
The engine must be running for the heated
steering wheel to operate.
Vehicles Equipped with Remote Start
On models that are equipped with remote start,
the heated steering wheel and seat can be
programmed to come on during a remote start.
Refer to “Remote Starting System — If
Equipped” in “Things to Know Before Starting
Your Vehicle” for further information.
WARNING!
• Persons who are unable to feel pain to the
skin because of advanced age, chronic
illness, diabetes, spinal cord injury, medi-
cation, alcohol use, exhaustion, or other
physical conditions must exercise care
when using the steering wheel heater. It
may cause burns even at low tempera-
tures, especially if used for long periods.
• Do not place anything on the steering
wheel that insulates against heat, such as a
blanket or cushion. This may cause the
steering wheel heater to overheat.
ELECTRONIC SPEED CONTROLWhen engaged, the Electronic Speed Control
takes over accelerator operations at speeds
greater than 25 mph (40 km/h).
The Electronic Speed Control buttons are lo-
cated on the right side of the steering wheel.
11 6

WARNING!
•Adaptive Cruise Control (ACC) is a conve-
nience system. It is not a substitute for
active driving involvement. It is always the
driver’s responsibility to be attentive of
road, traffic, and weather conditions, ve-
hicle speed, distance to the vehicle ahead;
and, most importantly, brake operation to
ensure safe operation of the vehicle under
all road conditions. Your complete attention
is always required while driving to maintain
safe control of your vehicle. Failure to fol-
low these warnings can result in a collision
or serious personal injury.
• The ACC system:
Does not react to pedestrians, oncoming
vehicles, and stationary objects (i.e., a
stopped vehicle in a traffic jam or a
disabled vehicle).
Cannot take street, traffic, and weather
conditions into account, and may be
limited upon adverse sight distance con-
ditions.
(Continued)WARNING!(Continued)
Does not predict the lane curvature or
the movement of preceding vehicles and
will not compensate for such changes.
Does not always fully recognize com-
plex driving conditions, which can result
in wrong or missing distance warnings.
Can only apply a maximum of 25% of
the vehicle’s braking capability, and will
not bring the vehicle to a complete stop.
WARNING!
You should switch off the ACC system:
• When driving in fog, heavy rain, heavy
snow, sleet, heavy traffic, and complex
driving situations (i.e., in highway construc-
tion zones).
• When entering a turn lane or highway off
ramp; when driving on roads that are wind-
ing, icy, snow-covered, slippery, or have
steep uphill or downhill slopes; and when
towing a trailer.
(Continued)
WARNING!(Continued)
• When circumstances do not allow safe
driving at a constant speed.
Failure to follow these warnings can result in a
collision or serious personal injury.
The Cruise Control system has two control
modes:
• Adaptive Cruise Control mode for maintain-
ing an appropriate distance between ve-
hicles.
• Normal (fixed speed) cruise control mode for
cruising at a constant preset speed. For
additional information, refer to “Normal
(Fixed Speed) Cruise Control Mode” in this
section. Note:The system will not react to
preceding vehicles. Always be aware of the
mode selected.
You can change the mode by using the Cruise
Control buttons. The two control modes func-
tion differently. Always confirm which mode is
selected.
11 9

Adaptive Cruise Control (ACC)
Operation
The speed control buttons (located on the right
side of the steering wheel) operates the ACC
system.NOTE:
Any chassis/suspension modifications to
the vehicle will effect the performance of the
Adaptive Cruise Control.
Activating Adaptive Cruise Control
(ACC)
You can only activate ACC if the vehicle speed
is above 25 mph (40 km/h).
When the system is turned on and in the READY
state, the Electronic Vehicle Information Center
(EVIC) displays “Adaptive Cruise Ready.”
When the system is OFF, the EVIC displays
“Adaptive Cruise Control Off.”
NOTE:
You cannot enable ACC under the following
conditions:
•
When in Four-Wheel Drive Low.
• When you apply the brakes.
• When the parking brake is set.
• When the automatic transmission is in
PARK, REVERSE or NEUTRAL.
• When pushing the RES + button without a
previously set speed in memory.
To ActivatePush and release the ON/OFF button. The ACC
menu in the EVIC displays “Adaptive Cruise
Ready.”
To turn the system OFF, push and release the
ON/OFF button again. At this time, the system
will turn off and the EVIC will display “Adaptive
Cruise Control Off.”
1 — DISTANCE SETTING
2 — RES +
3 — SET -
4 — CANCEL
5 — ON/OFF
6 — MODE
Adaptive Cruise Control Ready
120

•Keyless Enter-N-Go Display — If Equipped ......... 174
• Compass / Temperature Display ............... 174
• Customer-Programmable Features (System Setup) .... 177
• SOUND SYSTEMS .......................... 181
• UNIVERSAL CONSUMER INTERFACE (UCI) 1.0 —
IF EQUIPPED ............................ 181
• Connecting The iPod or External USB Device ...... 181
• Using This Feature ....................... 181
• Controlling The iPod or External USB Device Using
Radio Buttons .......................... 182
• Play Mode ............................ 182
• List Or Browse Mode ...................... 183
• Bluetooth Streaming Audio (BTSA) ............. 184
• STEERING WHEEL AUDIO CONTROLS ............. 184
• Radio Operation ......................... 185
• CD Player ............................. 185
• CD/DVD DISC MAINTENANCE .................. 185
• RADIO OPERATION AND MOBILE PHONES .......... 185
154

The EVIC consists of the following:
•System Status
• Vehicle Information Warning Message Dis-
plays
• Personal Settings (Customer-Programmable
Features)
• Compass Display
• Outside Temperature Display
• Trip Computer Functions
The system allows the driver to select informa-
tion by pressing the following buttons mounted
on the steering wheel: UP Button
Press and release the UP button to
scroll upward through the main
menus (Fuel Economy, Vehicle
Info, Tire PSI, Cruise, Messages,
Units, System Setup) and sub
menus.
DOWN Button Press and release the DOWN but-
ton to scroll downward through the
main menus and sub menus.
SELECT Button Press and release the SELECT
button for access to main menus,
sub menus or to select a personal
setting in the setup menu. Press
and hold the SELECT button to
reset features.
BACK Button Press the BACK button to scroll
back to a previous menu or sub
menu.Electronic Vehicle Information
Center (EVIC) Displays
When the appropriate conditions exist, the
EVIC displays the following messages:
•Service Tire Pressure System
• Service Park Assist System
• Park Assist System Blinded
• Park Assist Disabled
• Front Sensor Blinded
• Rear Sensor Blinded
• Keyfob Battery Low
• Liftglass Open
• Left front turn signal lamp out
• Right front turn signal lamp out
• Left rear turn signal lamp out
• Right rear turn signal lamp out
• Check Tire Pressure
• ESC System Off
• Service blind spot system
EVIC Steering Wheel Buttons
164

WARNING!
In some circumstances a Transmission Tem-
perature Indicator, under continued operation,
could cause the fluid to boil over, come in
contact with hot engine or exhaust compo-
nents and cause a fire.
Engine Oil Change Indicator System
Oil Change Due
Your vehicle is equipped with an engine oil
change indicator system. The “Oil Change
Due” message will flash in the EVIC display for
approximately 10 seconds after a single chime
has sounded, to indicate the next scheduled oil
change interval. The engine oil change indica-
tor system is duty cycle based, which means
the engine oil change interval may fluctuate,
dependent upon your personal driving style.Unless reset, this message will continue to
display each time you turn the ignition switch to
the ON/RUN position. To turn off the message
temporarily, press and release the MENU but-
ton. To reset the oil change indicator system
(after performing the scheduled maintenance)
refer to the following procedure.
1. Turn the ignition switch to the ON position
(Do not start the engine).
2. Fully depress the accelerator pedal, slowly,
three times within 10 seconds.
3. Turn the ignition switch to the OFF/LOCK
position.
NOTE:
If the indicator message illuminates when
you start the vehicle, the oil change indica-
tor system did not reset. If necessary, repeat
this procedure.
Fuel EconomyPress and release the UP or DOWN button until
“Fuel Economy” displays highlighted in the
EVIC and press the SELECT button. Press and
release the UP/DOWN buttons until one of the
following Fuel Economy functions displays in
the EVIC:
•
Average Fuel Economy/Fuel Saver Mode
• Distance To Empty (DTE)
• Miles Per Gallon (MPG)
Press the UP/DOWN buttons to cycle through
all the Trip Computer functions.
The Trip Functions mode displays the following
information:
Average Fuel Economy / Fuel Saver
Mode — If Equipped
Shows the average fuel economy since the last
reset. When the fuel economy is reset, the
display will read “RESET” or show dashes for
two seconds. Then, the history information will
be erased, and the averaging will continue from
the last fuel average reading before the reset.
171

The FUEL SAVER MODE message will display
above the average fuel economy in the EVIC
display. This message will appear whenever
MDS (if equipped) allows the engine to operate
on four cylinders, or if you are driving in a fuel
efficient manner.
This feature allows you to monitor when you are
driving in a fuel efficient manner, and it can be
used to modify driving habits in order to in-
crease fuel economy.
Distance To Empty (DTE)
Shows the estimated distance that can be
traveled with the fuel remaining in the tank. Thisestimated distance is determined by a
weighted average of the instantaneous and
average fuel economy, according to the current
fuel tank level. DTE cannot be reset through the
SELECT button.
NOTE:
Significant changes in driving style or ve-
hicle loading will greatly affect the actual
drivable distance of the vehicle, regardless
of the DTE displayed value.
When the DTE value is less than 30 miles
(48 km) estimated driving distance, the DTE
display will change to a “LOW FUEL” message.
This display will continue until the vehicle runs
out of fuel. Adding a significant amount of fuel
to the vehicle will turn off the “LOW FUEL”
message and a new DTE value will display.
Vehicle SpeedPress and release the UP or DOWN button until
“Vehicle Speed” displays highlighted in the
EVIC and press the SELECT button. Press the
SELECT button to display the current speed in
mph or km/h. Pressing the SELECT button a
second time will toggle the unit of measure
between mph or km/hNOTE:
Changing the unit of measure in the Vehicle
Speed menu will not change the unit of
measure in the EVIC.
Trip InfoPress and release the UP or DOWN button until
“Trip Info” displays highlighted in the EVIC and
press the SELECT button. Press and release
the UP/DOWN buttons until one of the following
Trip functions displays in the EVIC:
•
Trip A
• Trip B
• Elapsed Time
Press the UP/DOWN buttons to cycle through
all the Trip Computer functions.
The Trip Functions mode displays the following
information:
Trip A
Shows the total distance traveled for Trip A
since the last reset.
Trip B
Shows the total distance traveled for Trip B
since the last reset.
Fuel Saver Mode — On
172

Elapsed Time
Shows the total elapsed time of travel since the
last reset when the ignition switch is in the ACC
position. Elapsed time will increment when the
ignition switch is in the ON or START position.
To Reset The Display
Reset will only occur while a resettable function
is being displayed. Press and release the SE-
LECT button once to clear the resettable func-
tion being displayed. To reset all resettable
functions, press and hold the SELECT button
for two seconds. Current display will reset
along with other functions
UnitsPress and release the UP or DOWN button until
“Units” displays highlighted in the EVIC and
press the SELECT button. The EVIC, odometer,
and navigation system (if equipped) can be
changed between English and Metric units of
measure. To make your selection, scroll up or
down until the preferred setting is highlighted,
then press and release the SELECT button until
a check-mark appears next to the setting,
showing that setting has been selected.
Vehicle Info
(Customer Information Features)
Press and release the UP or DOWN button until
“SYSTEM” displays highlighted in the EVIC and
press the SELECT button. Press the UP and
DOWN button to scroll through the available
information displays, then press SELECT to
display anyone of the following choices.
•Coolant Temp
Displays the actual coolant temperature.
• Oil Temperature
Displays the actual oil temperature.
• Oil Pressure
Displays the actual oil pressure.
• Trans Temperature
Displays the actual transmission temperature.
• Engine Hours
Displays the hours of engine operation.
Tire PSI
Press and release the UP or DOWN button until
“Tire PSI” displays highlighted in the EVIC and
press the SELECT button. Press and release the UP/DOWN buttons until one of the following
System Status messages displays in the EVIC:
•
System OK
• System Warnings Displayed (will display all
currently active System Warnings)
• Tire Pressure Monitor System (shows the
current pressure of all four road tires). For
additional information, refer to “Tire Pressure
Monitor System” in “Starting And Operating”.Tire Pressure Display
173

entering and exiting the vehicle. To make your
selection, press and release the SELECT but-
ton until a check-mark appears next to the
feature showing the system has been activated
or the check-mark is removed, showing the
system has been deactivated.
NOTE:
The seat will return to the memorized seat
location (if Recall Memory with Remote Key
Unlock is set to ON) when the RKE transmit-
ter is used to unlock the door. Refer to
“Driver Memory Seat” in “Understanding
The Features Of Your Vehicle” for further
information.
Tilt Mirror in Reverse
When this feature is selected, the outside rear-
view mirrors will tilt downward when the ignition
switch is in the RUN position and the transmis-
sion is in the REVERSE position. The mirrors will
move back to their previous position when the
transmission is shifted out of REVERSE. To
make your selection, press and release the
SELECT button until a check-mark appears
next to the feature showing the system has
been activated or the check-mark is removed,
showing the system has been deactivated.Key-Off Power Delay
When this feature is selected, the power win-
dow switches, radio, hands-free system (if
equipped), DVD video system (if equipped),
power sunroof (if equipped), and power outlets
will remain active for up to 10 minutes after the
ignition switch is turned OFF. Opening a vehicle
door will cancel this feature. To make your
selection, scroll up or down until the preferred
setting is highlighted, then press and release
the SELECT button until a check-mark appears
next to the setting, showing that setting has
been selected.
Illuminated Approach
When this feature is selected, the headlights
will activate and remain on for 0, 30, 60, or
90 seconds when the doors are unlocked with
the RKE transmitter. To make your selection,
scroll up or down until the preferred setting is
highlighted, then press and release the SE-
LECT button until a check-mark appears next
to the setting, showing that setting has been
selected.
Display Fuel Saver— If Equipped
The “ECO” message is located in the
Compass/Temperature display, this message
can be turned on or off. To make your selection,
press and release the FUNCTION SELECT but-
ton until “ON” or “OFF” appears.
Keyless Enter-N-Go (Passive Entry)
This feature allows you to lock and unlock the
vehicle’s door(s) without having to press the
RKE transmitter lock or unlock buttons. To
make your selection, press and release the
SELECT button until a check-mark appears
next to the feature showing the system has
been activated or the check-mark is removed,
showing the system has been deactivated.
Refer to “Keyless Enter-N-Go” in “Things To
Know Before Starting Your Vehicle”.
Auto High Beams
(Available with SmartBeam™ Only)
When this feature is selected, the high beam
headlights will deactivate automatically under
certain conditions. To make your selection,
press and release the SELECT button until a
check-mark appears next to the feature show-
ing the system has been activated or the
check-mark is removed, showing the system
179

Display Units of Measure In:
The EVIC, odometer, and Uconnect™ gps (if
equipped) can be changed between English
and Metric units of measure. To make your
selection, press and release the SELECT but-
ton until “ENGLISH” or “METRIC” appears.
Calibrate Compass
Refer to “Compass Display” for more informa-
tion.
Compass Variance
Refer to “Compass Display” for more informa-
tion.
SOUND SYSTEMSRefer to your Sound Systems Booklet.
UNIVERSAL CONSUMER INTERFACE
(UCI) 1.0 — IF EQUIPPED
NOTE:
This section is for sales code RES and
REQ/REL/RET radios only with Uconnect™.
For sales code RER, REN, RBZ, REP, REW,
RB2 or REZ touch-screen radio UCI feature,
refer to the separate RER, REN, RBZ, RB2 orREZ User’s Manual. UCI is available only if
equipped as an option with these radios.
This feature allows an iPod
or external USB
device to be plugged into the USB port.
UCI supports Mini, 4G, Photo, Nano, 5G iPod 
and iPhone devices. Some iPod software
versions may not fully support the UCI features.
Please visit Apple’s website for software up-
dates.
NOTE:
• If the radio has a USB port, refer to the
appropriate Uconnect™ Multimedia radio
User’s Manual for iPod or external USB
device support capability.
• Connecting an iPod or consumer elec-
tronic audio device to the AUX port lo-
cated in the radio faceplate, plays media,
but does not use the UCI feature to con-
trol the connected device.
Connecting The iPod or External
USB Device
Once the audio device is connected and syn-
chronized to the vehicle’s UCI system (iPod 
device may take a few minutes to connect), the audio device starts charging and is ready for
use by pressing radio switches, as described
below.
NOTE:
If the audio device battery is completely
discharged, it may not communicate with
the UCI system until a minimum charge is
attained. Leaving the audio device con-
nected to the UCI system may charge it to
the required level.
Using This FeatureBy using iPod cable or external USB device to
connect to USB port:
•
The device audio can be played on the
vehicle’s sound system, providing metadata
(artist, track title, album, etc.) information on
the radio display.
• The audio device can be controlled using
the radio buttons to Play, Browse, and List
the iPod contents.
• The audio device battery charges when
plugged into the UCI connector (if supported
by the specific audio device)
181