lock JEEP WRANGLER 2004 TJ / 2.G User Guide

Here are some tips on getting the most out of your child
restraint:
²Before buying any restraint system, make sure that it
has a label certifying that it meets all applicable Safety
Standards. The manufacturer also recommends that
you make sure that you can install the child restraint in
the vehicle where you will use it before you buy it.
²The restraint must be appropriate for your child's
weight and height. Check the label on the restraint for
weight and height limits.
²Carefully follow the instructions that come with the
restraint. If you install the restraint improperly, it may
not work when you need it.
²The passenger seat belts are equipped with cinching
latch plates designed to keep the lap portion or lap belt
tight around the child restraint so that it is not
necessary to use a locking clip. Pull up on the shoulder
portion of the lap/shoulder belt, or on the free end of
the lap belt to tighten the belt. The cinching latch plate
will keep the belt tight, however, any seat belt system
will loosen with time, so check the belt occasionally
and pull it tight if necessary.
²In the rear seat, you may have trouble tightening the
lap belt or lap/shoulder belt on the child restraint
because the buckle or latch plate is too close to the belt
path opening on the restraint. Disconnect the latch
plate from the buckle and twist the short buckle-end
belt several times to shorten it. Insert the latch plate
into the buckle with the release button facing out.
²If the belt still cannot be tightened, or if pulling and
pushing on the restraint loosens the belt, disconnect
the latch plate from the buckle, turn the buckle
around, and insert the latch plate into the buckle
again. If you still cannot make the child restraint
secure, try a different seating position.
²Buckle the child into the seat according to the child
restraint manufacturer's instructions.
²When your child restraint is not in use, secure it with
the seat belt or remove it from the vehicle. Do not leave
it loose in the vehicle. In a sudden stop or collision, it
could strike the occupants or seat backs and cause
serious personal injury.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

Many, but not all restraint systems will be equipped with
separate straps on each side, with each having a hook or
connector for attachment to the lower anchorage and a
means of adjusting the tension in the strap. Forward-
facing toddler restraints and some rear-facing infant
restraints will also be equipped with a tether strap, a
hook for attachment to the tether strap anchorage and a
means of adjusting the tension of the strap.
You will first loosen the adjusters on the lower straps and
on the tether strap so that you can more easily attach the
hooks or connectors to the vehicle anchorages. Next
attach the lower hooks or connectors over the top of the
anchorage bars, pushing aside the seat cover material.
Then lift the tether anchorage cover directly behind the
seat where you are placing the child restraint and attach
the tether strap to the anchorage, being careful to route
the tether strap to provide the most direct path between
the anchor and the child restraint. If the Add-A-TrunkŸ
option is present in the vehicle, the lid should be opened
and positioned against the back of the rear seat prior to
attaching and adjusting the strap. Finally, tighten all three
straps as you push the child restraint rearward anddownward into the seat, removing slack in the straps
according to the child restraint manufacturer's instruc-
tions.
WARNING!
Improper installation of a child restraint to the
LATCH anchorages can lead to failure of an infant or
child restraint. The child could be badly injured or
killed. Follow the manufacturer's directions exactly
when installing an infant or child restraint.
Installing Child Restraints Using the Vehicle Seat
Belt
The passenger seat belts are equipped with cinching latch
plates, which are designed to keep the lap portion tight
around the child restraint so that it is not necessary to use
a locking clip. Pull up on the shoulder portion of the
lap/shoulder belt to tighten the belt. The cinching latch
plate will keep the belt tight, however, any seat belt
system will loosen with time, so check the belt occasion-
ally and pull it tight if necessary.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

WARNING!
If the hood is not fully latched, it could fly up when
the vehicle is moving and block your forward vision.
Be sure all hood latches are latched fully before
driving.
LIGHTS
Interior Lights
The overhead light comes on when a door is opened. It
may also be turned on by rotating the control for the
dimmer switch on the muti-function control lever fully
upward.
The overhead light will automatically turn off in about 20
minutes if a door is left open or the dimmer control is left
in the dome light position. Turn the ignition switch ON to
restore the overhead light operation.
Daytime Brightness Feature
Certain instrument panel components (odometer, radio
display) can be illuminated at full brightness during the
daytime. This can be helpful when driving with your
headlights on during the daytime such as in a parade or
a funeral procession. To activate this feature, rotate the
left stalk one detent lower than the dome light.
Multi-Function Control Lever
The multi-function control lever controls the operation of
the parking lights, headlights, headlight beam selection,
passing light, fog lights, instrument panel light dimming,
and turn signals.
56 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

TILT STEERING COLUMN
To tilt the column, push down on the lever below the turn
signal control and move the wheel up or down, as
desired. Pull the lever back upwards to lock the column
firmly in place.WARNING!
Tilting the steering column while the vehicle is
moving is dangerous. Without a stable steering col-
umn, you could lose control of the vehicle and have
an accident. Adjust the column only while the ve-
hicle is stopped. Be sure it is locked before driving.
ELECTRONIC SPEED CONTROL
When engaged, this device takes over accelerator opera-
tions at speeds greater than 35 mph (60 km/h). The
controls are mounted on the steering wheel and consist of
ON´OFF, SET, RESUME/ACCEL, CANCEL, and COAST
controls.
60 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

STORAGE
Glove Compartment
To unlock the glove compartment, insert the key and
turn. To open, pull the latch up.
Console Storage Compartment Ð If Equipped
To unlock, insert key and turn. To open, press the latch
button.
Add-A-TrunkŸ Ð If Equipped
The factory-installed Add-A-TrunkŸ option provides a
secured compartment for parcels or equipment when the
tailgate is closed and locked. To gain access to this
compartment, simply open the tailgate and release the
spring loaded latch pins. The cover of the Add-A-
TrunkŸ can then be raised.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 65
3

When the Add-A-TrunkŸ is not desired, it can be easily
removed from the rear compartment. Remove the four
knobs that secure the ªtrunkº to the body. Lift the
Add-A-TrunkŸ out and place the knobs in the molded-in
storage area. Storage space is also provided for the wheel
lock, and lock key tool.
Do not leave the Add-A-TrunkŸ loose in your vehicle.
Remove it and store it in a safe place.
DUAL TOP Ð IF EQUIPPED
If your vehicle is equipped with a Dual Top,you must
remove one of the tops from the vehicle.The soft top
was installed at the factory for shipping purposes only.
The soft top and the hard top are to be used indepen-
dently.Removal is mandatory to prevent any possible
wear and tear on the soft top, should both tops remain on
the vehicle at the same time. Failure to do so may void
your soft top warranty.
Removing The Soft Top
1. Locate and remove the 2 boxes that contain the
following items:
²right and left door frames
²door frame attachment knobs (4)
²right and left quarter windows
²rear tailgate window
2. Remove the hard top. Refer to ªHard Top Removalº in
this section.
3. Remove the soft top bow assembly pivot bracket
screws (2 per side) using a #30 Torxthead driver.
66 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

7. Disconnect the washer hose and install the tethered
cap.
CAUTION!
Make sure storage cap is installed to prevent foreign
materials from entering tube and clogging system.
8. Disconnect the wire harness from the hard top by
pressing the tab at the side of the connector and pulling
to disconnect.
NOTE:If the red latch on the connector is locked, push
the red latch to the right until you can only see the latch
on one end (right) of the connector. This will unlock
connector tab, allowing the tab to be pressed down and
enabling the harness to be disconnected from the hard
top.
9. Remove the hard top from the vehicle.
10. Fold the harness back and secure it to the main
harness using the attached Velcrotstrap, to prevent the
harness from rattling.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81
3

NOTE:If the doors are to be removed, pull the #4 fuse
from the fuse block to prevent dome lamp illumination.
Hard Top Installation
NOTE:
If the door frames are installed from soft top
usage, they must be removed prior to installation of the
hard top.
1. Inspect the hard top seals for damage and replace if
necessary.
2. Install the hard top using the same steps for removal
in reverse order.
NOTE:The hard top must be positioned properly to
ensure sealing. Set the hard top on the windshield frame
so that there is no overhang. Also, make sure that the
hard top is sitting flush with the body at the sides and
check to ensure that there is a uniform gap between the
lift glass and hard top.
SOFT TOP
CAUTION!
²The soft top is not designed to carry any addi-
tional loads such as roof racks, spare tires, build-
ing, hunting, or camping supplies, and/or lug-
gage, etc. Also, it was not designed as a structural
member of the vehicle, and thus cannot properly
carry any additional loads other than environmen-
tal (rain, snow, etc.).
²The soft top does not include any devices to
properly secure any loads on the roof, and any
damage (structural or surface finish) that occurs
due to any additional loading to the top area will
void any vehicle warranty.
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

5. Open the tailgate, partially unzip the rear window on
each side, and unlock the rear window retainers.
NOTE:If zippers are difficult to operate due to road
dust, etc., clean them with a mild soap solution and a
small brush. Cleaning products are available through
Mopartdistributors.6. Pull the retainer bar straight out from the tailgate clips.
²Remove the rear window entirely. This is done by
unzipping the window bringing the right zipper tab
all the way to the end of the zipper track at the
bottom left corner. Stow the windows carefully to
avoid scratching, pull up on the window to disen-
gage zipper end.
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

5. To safely store the side bars in your vehicle, use four of
the cinch straps, found in the glove box. Attach the straps
through the footman loops located in the floor behind the
folded rear seat on each side of the vehicle.
WARNING!
You or others could be injured if you carry the side
bars loose in your vehicle. Remove the bars from the
vehicle or securely store them as described or they
may cause personal injury if an accident occurs. See
your authorized dealer for replacement if the cinch
straps are not found in the glove box.
6. Remove the windshield wipers by first pulling the
wiper away from the windshield and out to the ªlockº
position. Then, using a small flat tool such as a screw
driver, release the retaining clip. Lift the wipers off and
store in center console or securely behind the rear seat.
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE