instrument cluster KIA K5 2021 Features and Functions Guide

STEERING WHEEL CONTROLS
STEERING WHEEL CONTROLS
*IF EQUIPPED22K5 FEATURES & FUNCTIONS GUIDE
Daytime Running Lights (DRL) - DRL may help others to see the
front of your vehicle during the day. The lights will turn on automatically
when the ignition or Engine Start /Stop button is ON and the headlight
switch is in the AUTO position, unless one of the following occurs:
• Headlights are on
• Parking brake is applied
• Engine is turned off
• Switch is in the DRL OFF position
Headlight position
Parking light position
AUTO*Auto Light / HBA
OFFOFF position
Headlights & High Beams
To o p e r a t e :
•Rotate lever A to change the Headlight function
•Push lever to turn High Beams ON B
•Pull lever to flash Headlights/High Beams B
REMINDERS:
• High Beam Assist does not operate below certain speeds, or in some lighting and driving conditions. Please be aware of your surroundings and exercise proper road etiquette when operating a vehicle using the high beams
• DRL only operates during the daytime
• HBA will operate when vehicle speed exceeds 25 mph
• If the lever is pushed away from you while HBA is operational, HBA will turn off and the high beams will be on continuously. If the lever is pulled toward you while HBA is operational, HBA will turn off
• If the light switch is switched to the headlight position, HBA will turn off and low beams will be on continuously
• When the HBA indicator illuminates on the instrument cluster, the HBA is not working properly. See an authorized Kia dealer for service
See section 4 in the Owner’s Manual for more information.
AUTO Light position – When the light switch is in the AUTO Light position, the taillights and headlights
will turn ON/OFF automatically depending on the amount of light outside the vehicle.
High Beam Assist (HBA) – High Beam Assist is designed to automatically adjust the headlight range by
switching between high and low beams based on light detected from other vehicles and road conditions.
To enable HBA, toggle the light switch to the AUTO Light position and turn on the high beams by pushing
the lever away from you. The High Beam Assist indicator will illuminate.
OFFAUTO
OFFAUTO
0
20
40 60
80
100
120
140
160
180
200
220
240
260
0
1 2
3
4
5
6
7
8km/h
EPB
C H
x1000rpm
0
20 40
60
80
100
120
1 40
1 60
E
F
MPHP
One Touch Turn Si...
Back
Off
3 flashes
5 flashes
7 flashes
59

STEERING WHEEL CONTROLS
STEERING WHEEL CONTROLS
ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED23
Turn Signals & Fog Lights*
To o p e r a t e :
• Turn Signals - Move lever D Up/Down for Right /Left Turn Signal
• Fog Lights - Press switch up/down to turn Fog Lights ON/OFF
REMINDER: Headlights must be ON for fog light operation.
One-Touch Lane Change Signal is activated by
briefly pressing the Turn Signal Lever slightly for
less than 1 second and then releasing E. The lane
change signal will blink 3 times.
To change how many times the Lane Change Signal
blinks (3/5/7), go to User Settings Mode in the LCD
Instrument Cluster modes.
Refer to section 4 in the Owner’s Manual for more information.
For illustrative purposes only. Your actual display, buttons and/or features may vary.
Lifting Wipers (Wiper Service Mode)
To lift the windshield wipers to clean windshield, inspect or replace
wiper blades or raise wipers in snow/ice conditions without damaging
the hood, the blades need to be moved to the service position C to
prevent damaging the hood.
With the ignition ON, turn the ignition OFF, and within 20 seconds
move the wiper switch to the MIST position B and hold the switch
for more than two seconds until the
wiper blade is in the fully up position.
To return wipers to normal position,
turn the ignition ON, then activate
M I S T.
Refer to section 7 in the Owner’s Manual for more information.
Wiper Service Mode Video
To view a video on your mobile device, snap this QR Code or visit the listed website. Refer to inside front cover information.
QR CODE
www.youtube.com/KiaFeatureVideos
OFFAUTO
OFFAUTO
M I S T: Single wipeOFF: Wiper offI N T: Intermittent wipeLO: Slow wipeHI: Fast wipe
Windshield Wipers & Washers
To o p e r a t e :
•Move lever Up/Down to change Wiper modes
•Press switch A Up/Down to adjust
Intermittent Wipe Speed to Fast/Slow
•Pull lever to spray and wipe
•
•Pressing lever up increases Intermittent wipe frequency and wipe speed. Pressing lever down decreases frequency of wipes •Set the wiper to OFF position when the wiper is not in use
QUICK TIPS
AB
C
DE
See section 4 in the Owner’s Manual for more information.

24K5 FEATURES & FUNCTIONS GUIDE
STEERING WHEEL CONTROLS
STEERING WHEEL CONTROLS
*IF EQUIPPED †LEGAL DISCL AIMERS ON BACK INSIDE COVER
Smart Cruise Control (SCC) Video
To view a video on your mobile device, snap this QR Code or visit the listed website. Refer to inside front cover information.
www.youtube.com/KiaFeatureVideos
QR CODE
SCC is a supplemental system and is not a substitute for safe driving. It is the responsibility of the driver to always check the speed and distance to the vehicle ahead.
For illustrative purposes only. Your actual display, buttons and/or features may vary.
See section 5 in the Owner’s Manual for more information.
Smart Cruise Control (SCC)† 6 a , 21
Smart Cruise Control (SCC) is designed to maintain a predetermined distance from vehicles detected ahead by automatically
adjusting the driving speed as needed. When traffic is detected, the vehicle will slow down to maintain a set distance behind
traffic without depressing the accelerator or brake pedal.
With SCC on and activated and the vehicle distance set, when the system detects a vehicle slowing or stopping, the system can
bring the vehicle to a complete stop. When the vehicle ahead starts to move forward, SCC re-engages. If the vehicle ahead stops for
more than 3 seconds, the accelerator pedal or the RES+ button must be pressed to start moving the vehicle.
To set/adjust the SCC speed:
•Accelerate/decelerate to the desired speed
•Press the Driving Assist button A to turn system ON and set speed. The CRUISE
indicator will illuminate on the instrument cluster and the set speed will automatically
activate at the vehicle’s current speed
•Press the button B inward to pause/resume the cruise control
•Press the +/- button B up/down to increase/decrease the set speed. The SET indicator
light, set speed and vehicle distance will illuminate on the instrument cluster’s LCD
screen
To set the vehicle distance: Press the Vehicle Distance button C on the steering
wheel. Scroll through the selections and the vehicle-to-vehicle distance image changes
and displays on the Instrument Cluster LCD.
To pause/resume SCC operation: Press the button B to pause or resume Cruise Control.
To turn SCC system OFF: Press the Driving Assist button A. The CRUISE indicator on the
instrument cluster will turn OFF.
To adjust the sensitivity of SCC: Press the mode button D on the Steering Wheel. With the OK
button E, select Drive Assistance, then SCC Response. Then select Fast, Normal or Slow.
To change the cruise control mode from SCC to standard cruise control, press and hold
button C. Repeat to switch back to SCC mode (the SCC system must not be activated
to change modes).
( Type B Steering Wheel buttons)
A
B
C
D
E

26*IF EQUIPPED †LEGAL DISCL AIMERS ON BACK INSIDE COVERK5 FEATURES & FUNCTIONS GUIDE
STEERING WHEEL CONTROLS
STEERING WHEEL CONTROLS
CRUISE65mphAUTO
(Display on LCD screen)
Navigation-based Smart Cruise Control (NSCC)*†6a
Navigation-based Smart Cruise Control can automatically adjust the vehicle speed when
it detects a curved road ahead and when it receives road information from the navigation
system.
To turn on NSCC, go to the User Settings in the instrument cluster or the Vehicle Settings* in
the audio head unit, by selecting Driving Assistance, Highway Auto Speed Change. When SCC
is on and operating, and NSCC is turned on, then NSCC is enabled and the AUTO icon A will
illuminate white on the Instrument Cluster.
When NSCC detects a curve ahead, activates and reduces the vehicle speed, the AUTO
icon A will turn green. When the vehicle passes the curved road, the vehicle may return to
its previously set SCC speed.
Autoset (Automatic change of set speed) – NSCC automatically changes the set speed of
Smart Cruise Control using the speed limit information of the navigation system* to help you
drive at a safe speed.
REMINDERS:
•When the ignition is cycled, the system returns to its previous on or off state
•When SCC is turned on and operating, NSCC may activate
•NSCC requires an active navigation subscription
•NSCC is only available on controlled access roads and highways
See section 5 in the Owner’s Manual for more information. For more setting information, refer to the Car Infotainment System Quick Reference Guide.
NSCC is a supplemental system and is not a substitute for safe driving. It is the responsibility of the driver to always check the speed and distance to the vehicle ahead.
A

37ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED
Idle, Stop & Go Video
To view a video on your mobile device, snap this QR Code or visit the listed website.
Refer to inside front cover information.
www.youtube.com/KiaFeatureVideos
QR CODEIdle, Stop & Go (ISG) System
The ISG system is designed to reduce fuel consumption by automatically shutting
down the engine when the vehicle is at a standstill.
When the ISG system is ON and the vehicle is at a standstill, the engine will stop,
and the green AUTO STOP indicator A on the instrument cluster will illuminate.
The engine will restart when the brake pedal is released or the shift lever is moved
from D (Drive) to the R (Reverse) position or to Manual Shift mode. When engine
restarts, the green AUTO STOP indicator on the instrument cluster will turn off.
To deactivate the ISG System, press the ISG OFF button B. If you press again, the
system will be activated.
REMINDERS:
•ISG is active by default at vehicle startup. When ignition is cycled, ISG will turn ON again
•
Under certain conditions, the engine will restart automatically even if the brake pedal is still depressed
•
If the AUTO STOP indicator is continuously blinking yellow and the ISG button LED is on, please contact an authorized Kia dealer

•If the AUTO STOP indicator A is solid yellow, the system is functional, but just has not met all its enabling criteria to activate ISG at that time.
•
The ISG system is disabled when:
•A seat belt is unfastened
•The hood or a door is opened
•Battery condition is poor
•
The front or rear defroster is turned on
•
Engine coolant temperature is low
•
The outside ambient temperature is too low/high
•
Emission control devices activate
•
The vehicle is on a steep slope
QUICK TIPS
Images are for illustrative purposes only and may not reflect actual feature or operation.
See section 5 in the Owner’s Manual for more information.
0
20
40 60
80
100
120
140
160
180
200
220
240
260
0
1 2
3
4
5
6
7
8km/h
EPB
C H
x1000rpm
0
20 40
60
80
100
120
1 40
1 60
E
F
MPH
AUTO
HOLD
DRIVE
MODE
OFF
SHIFT
LOCK
RELEASE
P
R
N D
+
_
(Button on center console below gear shift)
A
B
CENTER PANEL
CENTER PANEL

40*IF EQUIPPEDK5 FEATURES & FUNCTIONS GUIDE
The Electronic Parking Brake (EPB) system utilizes
an electric motor to engage the parking brake.
Applying the Parking Brake
Depress the brake pedal and pull up the EPB
switch A. Ensure that the indicator light is
illuminated on the instrument cluster.
Releasing the Parking Brake
The EPB will automatically release when the
shifter is placed in Reverse or Drive.
To release EPB manually, depress the brake pedal, then press the
EPB switch A, with the ignition switch in the ON position. Ensure
that the indicator light is OFF.
Auto Hold temporarily maintains the vehicle at
a standstill even though the brake pedal is not
depressed after the driver brings the vehicle to a
complete stop by depressing the brake pedal. Auto
Hold can be turned ON/OFF using the AUTO HOLD
button B on the center panel below the gear shift.
Before Auto Hold will operate, the driver’s door,
engine hood and trunk must be closed.
The AUTO HOLD indicator on the Instrument
Cluster has four states:
White: Standby – With vehicle in Park and at a
standstill, when the AUTO HOLD button B
is pressed on, the indicator will illuminate white.
While driving the vehicle (vehicle is not at a
standstill), the Auto Hold indicator will remain white.
Green: Engaged – When coming to a complete
stop by depressing the brake pedal, the Auto Hold
indicator changes from white to green.
Off (not illuminated) – The indicator will turn OFF when the AUTO HOLD button B is manually pressed OFF or when the EPB is manually turned ON.
Yellow: Malfunction – When the indicator is illuminated yellow, there may be a
system malfunction. Take your vehicle to a local Kia dealer.
REMINDERS:
• Auto Hold only operates when vehicle is in Drive or Neutral. Auto Hold turns off when the ignition is cycled
• To reduce the risk of an accident, do not activate Auto Hold while driving downhill, backing up or parking your vehicle
• Do not solely rely on the Auto Hold system to keep the vehicle stopped. Always pay attention to traf fic and road conditions, and be prepared to depress the brakes
Refer to section 5 in the Owner’s Manual for more information.
Electronic Parking Brake (EPB) Video
To view a video on your mobile device, snap this QR Code or visit the listed website.
Refer to inside front cover information.
www.youtube.com/KiaFeatureVideos
QR CODE
AUTO
HOLD
OFF
SHIFT
LOCK
RELEASEP
R
N D
+
_
DRIVE
MODE
(Located below gear shift)
Electronic Parking Brake (EPB)Auto Hold

•When leaving your keys with parking lot attendants or valet, make sure to inform them how to operate the EPB
•Pull up and hold EPB switch for 3 seconds to increase brake pressure if parked on a decline or incline
•If parked on a steep incline, pull up the EPB switch for more than 3 seconds for a firmer EPB application
QUICK TIPS
REMINDERS:
•
As a bulb check, the EPB malfunction indicator will illuminate for approximately 3 seconds when the ignition switch is turned ON
•
If the warning light does not illuminate temporarily, or continues to remain lit, take your vehicle to an authorized Kia dealer and have the system checked
•The EPB should not be operated while the vehicle is moving
•
A click or electric brake motor sound may be heard while operating or releasing the EPB, but these conditions are normal and indicate that the EPB is functioning properly
Refer to page 4 for location of Instrument Cluster indicators. Refer to section 5 in the Owner’s Manual for more information. For illustrative purposes only. Your actual display, buttons and/or features may vary.
AB
CENTER PANEL
CENTER PANEL

ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED †LEGAL DISCL AIMERS ON BACK INSIDE COVER43
SeatbackLumbarSeatSeat Cushion
Power Adjustable Driver’s Seat*†1 6
Move/Press controls to adjust Seat forward/backward, Seat Cushion
tilt up/down, Seatback forward/backward or Lumbar up/down/
forward/backward.
REMINDER: Do not attempt to adjust the seat while the vehicle is moving. This could result in loss of control of the vehicle.
For illustrative purposes only. Your actual display, buttons and/or features may vary.
Refer to section 3 in the Owner’s Manual for more information.
D
DD
E
E
F
F
SET
1
2
Driver Position Memory System†1 6
The integrated system stores into memory the position of the Driver’s
Seat and the Outside Rearview Mirrors.
To store a seating position into memory, first place the shifter into P
(Park) while the ignition is ON. Then:
1. Adjust the driver’s seat and outside mirrors
2. Press the SET button A on the control panel. System will beep once
3. Press one of the memory buttons B within 5 seconds. The system
will beep twice when memory has been stored
4. “Driver (1 or 2) set is memorized” will appear on the instrument
cluster LCD screen
REMINDER: Do not attempt to operate the driver position memory system while the vehicle is moving. This could result in loss of control of the vehicle.
(Buttons located on Driver’s Door Panel)
A
B
Refer to section 3 in the Owner’s Manual for more information.SEATING
SEATING

44*IF EQUIPPED †LEGAL DISCL AIMERS ON BACK INSIDE COVERK5 FEATURES & FUNCTIONS GUIDE
6-Way Manual Adjustable Driver’s Seat*†1 6
Pull lever A to slide Seat forward/backward.
Pull lever B up several times to raise Seat Height. Push lever B down several times to lower Seat Height.
Pull lever C to adjust Seatback recline.
Press D to adjust Lumbar support.

When adjusting seat forward or backward, ensure seat clicks or locks into place before driving vehicle.
QUICK TIP
Do not attempt to adjust the seat while the vehicle is moving. This could result in loss of control of the vehicle.
For illustrative purposes only. Your actual display, buttons and/or features may vary.
Refer to section 3 in the Owner’s Manual for more information.
Front Seat Headrest Adjustment†9
To raise headrest: Pull headrest up to the desired position.
To lower headrest: Press lock E, then press the headrest down.
REMINDERS:
• Button may be hard to see if headrest is in its lowest position
• Do not operate the vehicle with the headrests removed. Headrests can provide critical neck and head support in an accident
AB
C
D
E
Refer to section 3 in the Owner’s Manual for more information.
SEATING
SEATING
Check rear seats
: Alarm OffOK
Rear Occupant Alert (ROA) with Door Monitoring
The Rear Occupant Alert (ROA) with Door Monitoring can help alert the driver when
a rear passenger may be left in the vehicle. The alert will be a message on the
Instrument Cluster stating to “Check rear seats” F and a chime will sound.
The factory default is set to OFF. To turn the system ON or OFF, go to User Settings
in the Instrument cluster or Vehicle Settings*, on the audio head unit select
Convenience, then Rear Occupant Alert and check /uncheck the box.
REMINDER: Always be sure to check the passenger areas before leaving the vehicle.
ROA is not a substitute for one’s attention. Always check the vehicle’s interior before exiting.
See section 4 in the Owner’s Manual for more information.
Image is for illustrative purposes only and may not reflect actual feature or operation.
F

48*IF EQUIPPED †LEGAL DISCL AIMERS ON BACK INSIDE COVERK5 FEATURES & FUNCTIONS GUIDE
Trunk Release Buttons
Press the button A to unlock the Trunk (located to the left of the
steering wheel).
With the Trunk unlocked, press the
exterior Trunk Release button B (located
underneath the Trunk lid) and pull the
Trunk lid up by the handle to open.
Smart Trunk with Auto Open*†1 4
When the Smart Key fob is on your person and you are within close proximity of the
back of the vehicle, the hazard warning lights will blink and a chime will sound for
about 3 seconds as an alert that the Smart Trunk is about to open.
Then the alert system will blink and chime two additional times before opening the
Smart Trunk.
The Smart Trunk feature is OFF by default. To enable the Smart Trunk, go to User
Settings in the LCD Instrument Cluster modes or Vehicle Settings* in the audio head
unit (vehicles with Navigation).
During the Smart Trunk alert, the Smart Power Trunk can be deactivated with the Smart Key by pressing any button on the key fob.
QUICK TIPS

•The Trunk must be unlocked before it can be opened by the Trunk Release Button •Smart Key* - The Trunk unlocks automatically, can then be opened manually, (tail lights flash two times), and automatically locks when closed (tail lights flash one time), when the Smart Key fob* is within close proximity to the vehicle
QUICK TIPS
REMINDERS:
•
The Smart Key must be outside of the vehicle for the Smart Power Trunk to operate
•All doors are closed and locked after about 15 seconds
•
The Smart Trunk feature will not operate when the doors are recently closed and locked, and the Smart Key is still detected after 15 seconds near the vehicle or within 60 inches of the door handles, a door is not locked or closed, or the Smart Key is in the vehicle
•
Press any button on the Smart Key fob during the Detect and Alert stage to deactivate the Smart Power Trunk function
•
When the ignition is on, the Smart Trunk will only operate with the gear shift in the Park (P) position
•Ensure obstacles and people are out of the way of the Smart Trunk
For more information on the S mar t Trunk operation, please refer to the Owner's Manual.
For illustrative purposes only. Your actual display, buttons and/or features may vary.
HOLD
HOLD
HOLD
A
B
OTHER KEY FEATURES
OTHER KEY FEATURES

49ALWAYS CHECK THE OWNER’S MANUAL FOR COMPLETE OPER ATING INFORMATION AND SAFET Y WARNINGS. *IF EQUIPPED †LEGAL DISCL AIMERS ON BACK INSIDE COVER
(Images shown are for illustration purposes only. Actual operation may vary)
Reverse Parking Distance Warning (PDW)*†6a
Reverse Parking Distance Warning (PDW ) is a supplemental system that
is designed to assist the driver by chiming if any object is detected within
the sensing area to the rear and side of the vehicle when backing up.
When the ignition is ON, the system is activated.
REMINDERS:
•
If the vehicle is moving at speeds over 3 mph, the system may not activate correctly
•
When more than two objects are sensed at the same time, the closest one will be recognized first
Parking Distance Warning-Reverse is not a substitute for proper and safe backing-up procedures. Always drive safely and use caution when backing up. Parking Distance Warning-Reverse may not detect every object behind the vehicle.
For illustrative purposes only. Your actual display, buttons and/or features may vary.
The PDW warning volume can be adjusted in the User Settings in the Instrument Cluster or the Vehicle Settings* on the audio head unit.
QUICK TIP
Reverse Parking Collision-Avoidance Assist
(PCA)*†6a
Reverse Parking Collision-Avoidance Assist (PCA) is designed to detect
certain objects/pedestrians behind the vehicle and issues an audible
warning and/or applies emergency braking to reduce the possibility of a
collision when the vehicle is in reverse.
PCA can be turned on in the User Settings in the instrument cluster or the
Vehicle Settings* in the audio head unit by selecting Driver Assistance,
Parking Safety and then one of the following: Active Assist, Warning Only,
Of f.
When a potential collision is detected, the system applies emergency
braking for about two seconds. A warning message on the Instrument
Cluster will display A reminding the driver to press the brake
immediately.
REMINDERS:
•
PCA is operational when Active Assist is selected in the Vehicle Settings
•
PCA will only operate when:
– The vehicle’s speed is below 6 mph
– The trunk is closed
– The gear shift is in R (Reverse)
– Other systems such as Rear View Monitor are operating under normal conditions
Brake Now!
A
OTHER KEY FEATURES
OTHER KEY FEATURES