lock LAND ROVER DEFENDER 1996 Workshop Manual

ELECTRICAL
23
REPAIR HEADLAMP LEVELLING SWITCH
Service repair no - 86.65.16
Remove
1.Remove 2 screws and withdraw switch panel
from lower fascia.
2.Disconnect multi-plug from rear of headlamp
levelling switch.
3.Remove knob from switch spindle.
4.Unscrew retaining nut and withdraw switch from
switch panel.
Refit
5.Fit switch into switch panel and secure with
retaining nut.
6.Fit switch knob.
7.Connect switch multi-plug.
8.Fit switch panel.HEADLAMP LEVELLING UNIT
Service repair no - 86.41.16
Remove
1.Remove headlamp
See Headlamp.
2.Disconnect headlamp levelling unit harness
plug.
3.Rotate levelling unit anti-clockwise to release
retaining lugs from mounting bracket on
headlamp body.
4.Release levelling unit spindle from retaining slot
on headlamp bezel and withdraw unit from
mounting bracket.
Refit
5.Fit levelling unit into mounting bracket and locate
unit spindle into slot in headlamp bezel.
6.Press in unit and rotate clockwise to engage
retaining lugs behind mounting bracket.
7.Connect levelling unit harness plug.
8.Fit headlamp
See Headlamp.

88INSTRUMENTS
2
REPAIR FUEL AND TEMPERATURE GAUGE
Service repair no - 88.25.26 - Fuel gauge
Service repair no - 88.25.14 - Temperature gauge
Remove
1.Remove instrument panel
See Instrument
panel
.
2.Release illumination bulb holder and disconnect
electrical leads from gauge.
3.Unscrew knurled nut and remove clamp
securing gauge.
4.Remove earth lead eylet from gauge stud.
5.Withdraw gauge from instrument panel
Refit
6.Fit gauge into instrument panel, locate earth
lead, and secure with clamp.
7.Fit bulb holder and electrical leads.
8.Fit instrument panel
See Instrument panel.CLOCK - FASCIA PANEL
Service repair no - 88.15.07
Remove
1.Remove 4 screws securing instrument panel to
fascia cowl.
2.Pull panel away fom fascia sufficient to
disconnect speedometer cable.
3.Disconnect electrical leads and bulb holder from
clock.
4.Unscrew knurled nut and remove clamp
securing clock.
5.Remove clock from instrument panel.
Refit
6.Fit clock into instrument panel and secure with
clamp.
7.Fit bulb holder and electrical leads.
8.Connect speedometer cable.
9.Secure instrument panel to fascia cowl.

INSTRUMENTS
3
REPAIR CLOCK - CENTRE DASH PANEL
Service repair no - 88.15.07
Remove
1.Remove 2 screws and withdraw switch panel
from centre dash.
2.Release illumination bulb holder and disconnect
electrical leads from clock.
3.Press in spring retainers and remove clock from
panel.
Refit
4.Fit clock into dash panel.
5.Fit electrical leads and bulb holder.
6.Secure switch panel to centre dash.WARNING LIGHT PANEL
Service repair no - 88.20.18
Remove
1.Remove 2 screws and withdraw warning light
panel.
2.Disconect both multi-plugs.
3.Disconnect illumination bulb leads.
4.Remove warning light panel.
Refit
5.Fit illumination bulb leads and multi-plugs to
warning light panel.
6.Secure warning light panel to instrument panel.

88INSTRUMENTS
4
REPAIR PRINTED CIRCUIT - WARNING LIGHT PANEL
Service repair no - 88.20.20
Remove
1.Remove warning light panel
See Warning light
panel
.
2.Remove 13 illumination bulb holders from light
panel.
3.Release printed circuit from locating pins and
remove from panel seatings.
Refit
4.Fit new printed circuit over panel seatings and
position on locating pins.
5.Fit illumination bulbs to secure circuit.
6.Fit warning light panel
See Warning light
panel
.FUEL GAUGE TANK UNIT - REAR FUEL TANK,
110/130
Service repair no - 88.25.30
WARNING: Ensure that fuel handling
precautions given in Section 01 -
Introduction are strictly adhered to when
carrying out the following instructions.
Remove
1.Disconnect battery.
2.Remove fuel filler cap.
3.Remove tank drain plug, allow fuel to drain into a
clean container, and refit plug.
4.On LH side of tank, disconnect fuel supply pipe
from outlet pipe on fuel gauge unit.
5.Disconnect electrical plug from fuel gauge unit.
6.Release locking ring and withdraw fuel gauge
unit from tank, complete with sealing ring.
Refit
7.Insert gauge unit into tank with float positioned to
base of tank. Fit new sealing washer, if
necessary.
8.Secure gauge unit with locking ring.
9.Fit electrical plug and reconnect fuel supply pipe.
10.Refill fuel tank.
11.Reconnect battery.

INSTRUMENTS
5
REPAIR FUEL GAUGE TANK UNIT - SIDE FUEL TANK
Service repair no - 88.25.31
WARNING: Ensure that fuel handling
precautions given in Section 01 -
Introduction are strictly adhered to when
carrying out the following instructions.
Remove
1.Disconnect battery.
2.Remove RH front seat cushion.
3.Release retaining catch and remove seat base
cover to gain access to fuel tank.
4.Disconnect electrical plug from fuel gauge unit.
5.Release locking ring and withdraw fuel gauge
unit from tank, complete with sealing ring.
Refit
6.Insert gauge unit into tank with float positioned
towards front of tank. Fit new sealing washer, if
necessary.
7.Secure gauge unit with locking ring.
8.Fit electrical plug.
9.Fit seat base cover and seat cushion.
10.Reconnect battery.