differential LAND ROVER DEFENDER 1996 Owner's Guide

FRONT AXLE AND FINAL DRIVE
5
OVERHAUL 38.Place retaining plate, joint washer and oil seal
over axle flange ready for assembly.
39.Fit swivel bearing housing to axle flange with 7
bolts. Tighten to
73 Nm (54 lbf/ft).
40.Grease and fit upper and lower swivel pin taper
roller bearings.
41.Position swivel pin housing over swivel bearing
housing.
42.Coat joint washer both sides with sealing
compound and position on lower swivel pin.
43.Loosely fit brake shield bracket plus lower swivel
pin with lug outboard to swivel pin housing.
44.Loosely fit top swivel pin plus existing shims and
brake hose bracket to swivel pin housing.
45.Apply Loctite 270 or equivalent to lower swivel
pin bolts.
78 Nm (58 lbf/ft),bend over lock tabs.
46.Tighten top swivel pin bolts to
78 Nm (58 lbf/ft).
Check and adjust preload on bearings
NOTE: Swivel housing oil seal and axle
should not be fitted.
47.Attach a spring balance to ball joint bore and pull
balance to determine effort required to turn
swivel pin housing.
Resistance, once initial inertia has been
overcome, should be1.16 to 1.46 kg.Adjust by
removing or adding shims to top swivel pin.
48.When setting is correct remove top swivel bolts,
apply Loctite 270 or equivalent. Refit bolts and
tighten to
78 Nm (58 lbf/ft),and bend over lock
tabs.
49.Apply recommended grease between lips of
swivel oil seal.50.Fit oil seal, joint washer and retaining plate with
7 bolts and spring washers. Tighten to
11 Nm (8
lbf/ft).
51.Fit tie rod and drag link and secure with new
cotter pins. Tighten fixing to
40 Nm (30 lbf/ft).
52.Fit brake disc shield.
53.Loosely fit lock stop bolt and nut.
54.Apply a recommended grease between lips of
swivel housing oil seal.
55.Secure oil seal with retaining plate and securing
bolts. Tighten to
11 Nm (8 lbf/ft).
56.Fit track-rod and drag link and secure with new
cotter pins.
57.Loosely fit lock stop bolt for later adjustment.
58.Fit brake disc shield.
Fit driveshaft and stub axle
59.Insert axle shaft, and when differential splines
are engaged, push assembly in fully.
CAUTION: Take care not to damage axle
shaft oil seals.
60.Place a new joint washer in position on swivelpin
housing to stub axle mating face. Coat threads
of stub axle bolts with Loctite 270.
61.Fit stub axle with flat at 12 O'clock position.
CAUTION: Ensure that constant velocity
joint bearing journal is butted against
thrust ring on stub axle before stub axle is
secured.
62.Place mud shield in position and secure stub
axle to swivel pin housing with 6 bolts and
tighten evenly to
65 Nm (48 lbf/ft).
63.Fit brake jump hoses to brake jump hose
bracket.
64.Fit complete front hub assembly
See Repair,
Front hub assembly
.
65.Check swivel pin housing oil drain plug is fitted.
66.Fill swivel assembly to correct level, with new oil
See SECTION 10, Maintenance, Under
vehicle maintenance
.
NOTE: On later vehicles fill swivel pin
housing with 0.33 Litres of Molytex EP 00
grease.
67.Set steering lock stop bolts
See STEERING,
Adjustment, Steering lock stops
.

FRONT AXLE AND FINAL DRIVE
1
SPECIFICATIONS, TORQUE REV: 05/99 TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
FRONT AXLE
Hub driving member to hub 65*.......................................................................
Brake disc to hub 73.......................................................................................
Stub axle to swivel pin housing 65*.................................................................
Brake caliper to swivel pin housing 82............................................................
Upper swivel pin to swivel pin housing 78*.....................................................
Lower swivel pin to swivel pin housing 78*.....................................................
Oil seal retainer to swivel pin housing 11........................................................
Swivel bearing housing to axle case 73*.........................................................
Pinion housing to axle case 41.......................................................................
Crown wheel to differential housing 58...........................................................
Differential bearing cap to pinion housing 90..................................................
Differential drive flange to drive shaft 47.........................................................
Mudshield to bracket lower swivel pin 11........................................................
Bevel pinion nut 130........................................................................................
Draglink to hub arm 40....................................................................................
Panhard rod to axle bracket 88.......................................................................
Radius arm to axle 190....................................................................................
Radius arm to chassis side member 190.........................................................
NOTE: * These bolts to be coated with Loctite 270 prior to assembly.

STEERING
3
FAULT DIAGNOSIS STEERING DAMPER
The power steering system, as well as reducing the
effort required to manoeuvre the vehicle when
parking, also helps to dampen any deflections of the
road wheels, being transmitted back to the steering
wheel.
When operating the vehicle off road, the road wheels
are often deflected by ruts and boulders causing the
steering wheel to turn left and right. This phenomenon
is known as 'steering kickback'. To subdue the effects
of 'steering kickback', a hydraulic damper is fitted in
the steering linkage between the track rod and the
differential casing. The damper, which offers the same
resistance in extension and compression, is sealed for
life.
Steering damper check
Check the condition operation of the hydraulic
steering damper as follows:
Check procedure
1.Inspect damper for casing damage or leaks.
2.Clamp one end of the damper horizontally in a
vice using soft jaws. Compress and extend the
unit by hand. Resistance should be equal in both
directions.
3.If it is felt that the unit is outside acceptable
limits, fit a new steering damperSTEERING FAULTS
Symptom:-
Excessive kickback through steering wheel - when
driven on rough terrain.
1.Is the steering damper in good working order?
See Steering Damper.
NO - Renew unit
See Repair, Steering
Damper
.
YES - Continue.
2.Is there any looseness or free play in the
steering ball joints and linkage?
YES -
See Steering Linkage Inspect.
NO - Continue.
3.Is there any looseness or worn bushes in front
suspension?
YES -
See FRONT SUSPENSION, Repair,
Radius Arm
.
NOTE: When replacing suspension bushes
ALL bushes and fixings must be replaced.
NO - Continue.
4.Is the steering exceptionally light/sensitive when
driven on good road surface?
YES - See fault symptom -Steering
excessively light/sensitive and freeplay at
steering wheel.
NO - Suspect axle swivel resistance.
5.Check the resistance of the axle swivels
See
FRONT AXLE AND FINAL DRIVE, Overhaul,
Front Stub Axle, Constant Velocity Joint and
Swivel Pin Housing
.

STEERING
13
REPAIR REV: 05/99 TRACK ROD AND LINKAGE
Service repair no - 57.55.09
Remove
1.Park vehicle on level ground and chock rear
wheels.
2.Raise vehicle and locate axle stands or use a
ramp.
3.Centralise steering
See Adjustment,
Centralise steering box
.
4.Unscrew 2 bolts and remove track rod protection
bracket from axle differential housing.
5.Remove split pin and castellated nut securing
track rod to swivel housing arms.
6.Disconnect track rod ball joints using
LRT-57-018.
7.Remove track rod.
8.Slacken clamp bolts.
9.Unscrew ball joints.

57STEERING
14
REPAIRREV: 05/99 Refit
10.Fit new ball joints to track rod and loosely tighten
clamp bolts.
11.Screw in ball joints to full extent of threads and
fully tighten clamp bolts.
CAUTION: A track rod that is damaged or
bent must be renewed. DO NOT attempt to
repair or straighten it.
12.Fit track rod to swivel housing arms and tighten
ball joint nuts to
40 Nm (30 lbf/ft).Fit new split
pin.
13.Fit track rod protection bracket to axle differential
housing.
14.Check wheel alignment
See Adjustment,
Front wheel alignment
.
15.Remove axle stands or vehicle from ramp.

REAR SUSPENSION
1
DESCRIPTION AND OPERATION DESCRIPTION
The rear suspension design locates the rear axle with
two round section steel lower link arms and a forged
'A' frame, upper link assembly. This system allows
maximum axle articulation and wheel travel while
maintaining roll stiffness and directional stability.
The link arm is secured by a single retaining nut to the
chassis mounting, comprising a rubber bushed
bracket, which is retained by three fixings. A ferrule
rubber bush with a single retaining bolt is used to
secure the link arm to its axle mounting.
The upper link assembly is located on the rear
differential housing by a pivot ball-pin assembly. Two
brackets bolted to the chassis crossmember support
both sides of the 'A' frame of the link assembly,
secured by single retaining bolts.A Boge Hydromat self levelling unit can be fitted, as
an option, on 110/130 models to give additional
support when the vehicle is used to carry heavier
loads.
Two rubber bearing bushes, with retaining straps,
secure the rear of the anti-roll bar, if fitted, to the
chassis mountings, while bushed links support the
front of the anti-roll bar to the axle.
Conventional long travel coil springs and hydraulic
shock absorbers are used to control body movement.
The shock absorbers are secured to chassis mounting
brackets and fabricated lower mountings welded to to
the rear axle. Retaining plates are used to secure the
coil springs to the axle mounting while fabricated
brackets, welded to the chassis, are used for the
upper spring location.
Rear axle suspension
1.'A' frame, upper link assembly
2.Lower link
3.Coil springs
4.Shock absorber