torque LAND ROVER DISCOVERY 1995 Manual Online

STEERING
5
FAULT DIAGNOSIS Symptom :-
Steering excessively light/sensitive. Excessive
freeplay at steering wheel.
1.Are steering box adjustments correct?
NO -
See Adjustment, Power Steering Box
WARNING: Adjustments of steering box
should not be required while in warranty
period. If box is within warranty, it must be
returned to manufacturer. No attempt must be
made to introduce backlash.
YES - Suspect worn panhard rod or radius arm
bushes Check condition of ball joints and
the lower steering column shaft universal
joints for wear.
See Repair, Lower
Steering Shaft and Universal Joints
Symptom :-
Steering vibration, road wheel shimmy - wobble.
Vibration through the steering linkage powerful
enough to induce high frequency oscillation of the
steering wheel, is generally caused by out of balance
road wheels. However there are a number of other
possible causes of this symptom which if severe, may
be described as shimmy or wobble. Regardless of the
terminology used by the owner/driver to describe the
symptoms, the following diagnostic checks should be
carried out in the order presented.
1.Check the tyres and balance of the road wheels.
See GENERAL SPECIFICATION DATA,
Information, Wheels and Tyres See
WHEELS AND TYRES, Fault diagnosis, Fault
- Symptoms See WHEELS AND TYRES,
Repair, Wheel Balancing
2.Check the steering hydraulic damper function.
See Steering Damper
3.Check steering column universal joints for wear
and correct alignment.
See Repair, Lower
Steering Shaft and Universal Joints
4.Check steering linkage ball joints for wear,
correct alignment and security, including steering
box and tie rod.
See Steering Linkage Inspect
5.Check all front suspension rubbers for wear.
Check all fixing torques, including radius arm
bushes, panhard rod and anti-roll [sway] bar.
See FRONT SUSPENSION, Repair, Panhard
Rod See FRONT SUSPENSION, Repair,
Radius Arm See FRONT SUSPENSION,
Repair, Anti-Roll[Sway] Bar Assembly See
FRONT SUSPENSION, Repair, Front Shock
Absorber
6.Fit new radius arm bushes using NTC 6860. Fit
harmonic damper if vehicle has air suspension.
Fit new nuts, bolts and washers.
7. Coil spring vehicles only- If problem persists
fit damper kit STC 241 (2 off front) and STC
1474 (2 off rear). Road test vehicle.
8.Check the power steering box adjustments and
operation.
See Overhaul, Power Steering Box
9.Check the hub bearing end floats and determine
the condition of the hub bearings. As applicable.
See FRONT AXLE AND FINAL DRIVE, Repair,
Front Hub Assembly
10.Check the resistance and condition of the
swivels.
See FRONT AXLE AND FINAL
DRIVE, Description and operation,
Description
If problem is not diagnosed: Repeat
checks starting at 1.
11.Carry out a full steering geometry check.
See
INTRODUCTION, Information, Steering

57STEERING
8
FAULT DIAGNOSIS 4. DIRECTIONAL STABILITY
From 1. GENERAL STEERING:
1.Is directional stability concern when vehicle is
towing?
YES - Check towing/vehicle loading parameters
in Owner's Handbook.
NO - go to 3.
2.Is problem resolved?
YES - end
NO - continue.
3.Check condition of rear trailing link/chassis
bushes.
4.Is problem resolved?
YES - end
NO - continue.
5.Check condition of front and rear shock
absorbers. If in doubt change units in pairs, side
to side.
6.Is problem resolved?
YES - end
NO - continue.
7.Check steering damper.
See Steering Damper
8.Is problem resolved?
YES - end
NO - continue.
9.Check wheel balance
10.Is problem resolved?
YES - end
NO - contact local technical office.POWER STEERING FLUID LEAKS
1.Is fluid level correct?
YES - go to 3.
NO - Refill or drain to correct level. Bleed
system, check for leaks.
See Repair,
Power Steering System - Bleed
2.Is problem resolved?
YES - end
NO - continue.
3.Are hoses or joints leaking? Check on full lock
with engine at 2000 rev/min.
YES - loosen and retorque joints.
NO - go to 6.
4.Does leak remain?
YES - change PAS pipe.
NO - end.
5.Does leak remain?
YES - suspect seal in component. Check and
replace as necessary.
NO - end.
6.Is oil escaping from filler cap?
YES - bleed system.
See Repair, Power
Steering System - Bleed
NO - go to 8.
7.Is oil still escaping from filler cap?
YES - go back to 1.
NO - end.
8.Is oil leaking from PAS pump?
YES - go to 10.
NO - continue.
9.Is oil leaking from PAS box?
YES - go to 10.
NO - end.
10.Clean unit, add tracer dye to system. Retest
11.Is oil still leaking?
YES - establish leak point. Repair or replace
unit as necessary.
NO - end.

STEERING
11
FAULT DIAGNOSIS STIFF STEERING CHECKLIST
NOTE: Having completed visual checks
and steering assessment and confirmed
that vehicle steering load is incorrect carry
out the following procedure in order shown.
Steering wheel 'torque to turn' loads
1.Raise vehicle so both front wheels free.
2.With engine off, centralise steering wheel, and
remove air bag, if fitted or steering wheel pad.
Using torque wrench on column nut, check
torque required to turn the steering wheel one
turn in each direction.
3.Record readings obtained in each direction.
Compare figures obtained with the specified
figures:
Without ABS
4.40 Nm.
With ABS4.65 Nm.
NOTE: If figures are in excess of those
specified carry out steering box tie bar
reset below. If figures are as specified.
See Visual Check and Basic Adjustments
Steering box tie bar reset
1.Loosen the three tie bar fixings one complete
turn.
2.Drive vehicle carefully a short distance (within
the dealership) applying full lock in both
directions in order to settle steering components.
Drive vehicle over speed bumps and include
harsh braking if possible.
WARNING: Do not drive on public
highway.
3.Near end of 2. ensure vehicle is driven in a
straight line on level ground and halted.
4.Tighten panhard rod mounting arm nut,
110 Nm.
5.Tighten the two fixings tie bar to steering box,81
Nm.
6.Recheck steering wheel torque to turn. If torque
reading is still greater than specified, carry out
steering shaft universal joint lubrication.Lower steering shaft universal joint lubrication
1.Check lower steering shaft is correctly phased.
See Repair, Lower Steering Shaft and
Universal Joints
2.Lubricate universal joints with an anti-seizure
type penetrating spray. Work the joints to ensure
full penetration of the spray by driving vehicle
and steering from lock to lock.
3.If steering stiffness still persists carry out swivel
pin preload setting.
Swivel pin preload setting
The swivel pin preload setting must be checked and
set following the workshop manual procedure.
1.NON ABS vehicles.
See FRONT AXLE AND
FINAL DRIVE, Overhaul, Front Stub Axle,
Constant Velocity Joint and Swivel Pin
Housing Non ABS
Note that a pull load of 1.16 - 1.46 kg is required
after the axle shaft and swivel housing seal have
been removed.
2.ABS vehicles.
See FRONT AXLE AND FINAL
DRIVE, Overhaul, Front Stub Axle, Constant
Velocity Joint and Swivel Pin Housing ABS
Note that a torque to turn of 2.0 - 2.8 Nm is
required after the axle shaft and swivel housing
seal have been removed.
3.If steering stiffness still persists carry out
steering column alignment.

57STEERING
12
FAULT DIAGNOSIS Steering column alignment
1.Place vehicle on level ground. Measure the
angle of lower steering shaft using a Pernumeter
placed on the shaft between the universal joints.
The angle should measure a minimum of 12Ê.
2.If necessary, realign the shaft. Release the five
fixings securing the steering column. Position
column as required. Tighten the fixings evenly,
27 Nm.
3.Loosen the three screws securing lower steering
column shroud to upper shroud ensure lower
shroud is clipped to upper shroud. Reposition
shroud, tighten screws.
4.Recheck steering column angle.
Steering box adjustment
1.Check steering box adjustment.
See
Adjustment, Power Steering Box
Steering damper check
1.Check condition of steering damper
See
Steering Damper
VISUAL CHECK AND BASIC ADJUSTMENTS
NOTE: It is important that the following
instructions are carried out in the
sequence shown and the results recorded.
1.Road springs - check that road springs are
correctly seated and are to correct specification
for vehicle. For spring specification.
See
GENERAL SPECIFICATION DATA,
Information, Road Springs Data
2.Ride height - measure trim height from wheel
centre to wheelarch eyebrow. Record results on
data sheet.
3.Check/top up power steering fluid
See Repair,
Power Steering Fluid Reservoir
4.Check tension and condition of drive belt.See
ENGINE, Repair, Drive Belt
5.Track rod/drag link - check condition of track rod,
drag link and ball joints.
See Repair, Drag Link
and Drag Link Ends
If either component is damaged, check operation
of steering damper and steering box for
smoothness. Replace all damaged or worn
components that impair the operation of the
steering system.
6.Suspension bushes - examine all steering and
suspension bushes for signs of wear and
deterioration. Also check all fixings for torque
relaxation. Tighten to correct torque value.
See
FRONT SUSPENSION, Specifications, torque,
Torque Values
7.Oil leaks - check front and rear axle hubs for
leak and repair as necessary.
8.Brake system - check brake system for leaks,
pipe condition, pad wear/contamination, disc
wear/condition and ABS sensors for correct
fitting.
9.Hub end float - check movement in the hubs by
rocking the wheels.
10.Check front wheel alignment. Vehicles displaying
a tendency to veer more than considered
allowable, it is permissible to set the front track
to parallel.
11.Having completed all the above checks and
adjustments, road test vehicle.
See Road Test
Procedure
Attempting to reproduce the symptoms
established earlier. If symptoms still exist refer to
relevant Diagnostic Chart.

STEERING
1
ADJUSTMENT POWER STEERING BOX
Service repair no - 57.10.13
WARNING: Adjustments of steering box
should not be required while in warranty
period. If box is stiff or tight and within
warranty, it must be returned to manufacturer. No
attempt must be made to introduce backlash.
1.Apply park brake, select 'P' in automatic
transmission and chock wheels. Support chassis
front on axle stands.
2.Remove engine undertray.
3.Disconnect drag link from steering drop arm.
4.Check torque to turn.
See Fault diagnosis,
Stiff Steering Checklist
5.Centralise steering box.See Centralise
Steering Box
NOTE: Only check for no backlash when
steering box is in central position.
NOTE: If steering wheel is not straight, it
should be repositioned.
See Repair,
Steering Wheel
The adjustment of the steering box ensures
any preload or end float present on centre is
removed.
6.The adjustment is obtained by rocking the drop
arm about centre whilst an assistant slowly
tightens the steering box adjuster screw.
7.Tighten the locknut when all backlash has been
removed.
8.Repeat the check for backlash. If backlash exists
loosen locknut and repeat adjustment
procedure.
9.Turn steering wheel lock to lock and check no
tightness exists.
10.Ensure front wheels are aligned and in straight
ahead position.
See Front Wheel Alignment
11.Adjust drag link 924 mm between ball joint
centres.
12.Connect drag link. Tighten to
40 Nm.
13.Lower vehicle to ground level and remove
chocks.
14.Road test vehicle.
See Fault diagnosis, Road
Test Procedure
NOTE: If steering wheel is not in straight
ahead position when vehicle is travelling
in a straight line, drag link length is
incorrect and is pushing drop arm away from
central position.
Drag link adjust
15.Right hand drive vehicles - if steering wheel is to
right, drag link is too long. If steering wheel is to
left drag link is too short.
Left hand drive vehicles - if steering wheel is to
right, drag link is too short. If steering wheel is to
left drag link is too long.
16.Adjust drag link until steering wheel points
straight ahead when vehicle is travelling in a
straight line.
CENTRALISE STEERING BOX
1.To centralise the box, insert a suitable peg (hole
size 8.06 mm) into the rear of the drop arm and
into the steering box casing to enable rapid and
accurate setting on centre.

STEERING
1
REPAIR POWER STEERING FLUID PIPES
Service repair no - 57.15.21
CAUTION: If any joints are disconnected, it
is essential that open pipe and ports are
plugged to prevent ingress of dirt.
The following procedures must be followed when
refitting fluid pipes:
Power steering pump
1.Remove plugs, place clamp on feed hose.
V8i Steering pump illustrated
2.Push hose onto pump.
3.Hold clamp in position, Tighten to
3 Nm.
4.Fit high pressure union into pump.
5.Hold pipe in correct position. Tighten to
20 Nm.
6.Remove plugs and refit pipes to steering box,
leave fingertight.
7.Tighten to torque: 16mm thread
20 Nm.
14mm thread15 Nm.
Power steering reservoir
1.Remove plugs and refit pipes and clamps.
2.Tighten clamps to3 Nm.

57STEERING
6
OVERHAUL
61.Fit new worm adjuster sealing ring.
62.Loosely screw adjuster into casing.
63.Fit locknut, do not tighten.
64.Turn in worm adjuster until end float is almost
eliminated. Ensure bearing cages are seated
correctly.
65.Measure maximum rolling torque of valve and
worm assembly, using a torque wrench and
spline socket LRT-57-025.
66.Turn in worm adjuster while rotating shaft to
increase figure measured in instruction 65. to
0.56 Nm.
67.Back off worm adjuster 1/4 turn. Turn in worm
adjuster to increase reading at 65. by 0.21 - 0.34
Nm with locknut tight,
100 Nm.Use worm
adjusting wrench LRT-57-006 and locknut
wrench LRT-57-028.Fitting rack and piston
68.Screw slave bolt into piston to aid assembly.
69.Fit piston and rack so piston is 70 mm from outer
end of bore.
Fitting sector shaft
70.Fit sector shaft using seal saver LRT-57-021.
Align roller with cut out in casing - see
RR3934M. Push in sector shaft while rotating
input shaft to allow sector roller to engage worm.
Fitting rack adjuster
71.Fit rack adjuster and thrust pad to engage rack.
Back off half turn on adjuster.
72.Loosely fit new nylon pad and adjuster set screw
assembly.

57STEERING
8
OVERHAUL 83.Hold input shaft and rock drop arm to establish
backlash is present. Continue rocking and slowly
turn sector shaft adjusting screw clockwise.
Continue rotating adjuster screw until backlash
has almost been eliminated.
84.Refit locknut and tighten.
NOTE: It is important steering box is
centralised before any adjustments are
made.
85.Check maximum rolling torque one and a quarter
turns either side of centre position, using a
torque wrench and spline socket LRT-57-025.
Rotate adjuster screw to obtain across centre
torque of 0.34 Nm plus torque figure at one and
a quarter turns. Tighten adjuster locknut to
60
Nm.
Adjusting rack adjuster.
86.Turn in rack adjuster to increase figure
measured in instruction 85. by 0.23 - 0.34 Nm.
The final figure may be less, but must not
exceed 1.35 Nm.
87.Lock rack adjuster in position with grub screw.
Tighten to
5 Nm.
Torque peak check
With input shaft rotated from lock to lock, rolling
torque figures should be greatest across centre
position and equally disposed about centre position.
The condition depends on value of shimming fitted
between valve and worm assembly inner bearing cup
and casing. The original shim washer value will give
correct torque peak position unless major components
have been replaced.Procedure
88.With input coupling shaft toward the operator,
turn shaft fully counter-clockwise.
89.Check torque figures obtained from lock to lock
using torque wrench and spline socket
LRT-57-025.
90.Check also for equal engagement either side of
centre.
Adjustments
91.Note where greatest figures are recorded
relative to steering position.If greatest figures are
not recorded across centre of travel (steering
straight-ahead), adjust as follows:
If torque peak occursbeforecentre position,addto
shim washer value; if torque peak occursaftercentre
position,subtractfrom shim washer value,
refer to
fitting valve and worm assembly
.
Shim washers are available as follows:
0.03mm, 0.07mm, 0.12mm and 0.24mm.
NOTE: Adjustment of 0.07mm to shim
value will move torque peak area by 1/4
turn on the shaft.
CAUTION: When reshimming valve and
worm, extreme caution must be exercised
to prevent seal damage during
reassembly.

STEERING
1
SPECIFICATIONS, TORQUE STEERING PUMP
Make/type - V8i ZF 'Unicorn'................................................................
Make/type - Tdi Hobourn Eaton 500 series................................................................
Operating pressure - straight ahead position - at idle 7 bar, 100 lbf/in
2maximum ......
Full lock (left or right) at idle 28 bar, 400 lbf/in2minimum .............................................
Full lock (left or right) 1000 rev/min 70-77 bar, 1000-1100 lbf/in2..................................

57STEERING
2
SPECIFICATIONS, TORQUE TORQUE VALUES
NOTE: Torque wrenches should be regularly checked for accuracy to ensure that all fixings are
tightened to the correct torque.
Nm
Ball joint nuts 40..............................................................................................
Clamp bolt nuts 14..........................................................................................
Steering column bracket nuts 22....................................................................
Steering wheel nut 50.....................................................................................
Tie bar to mounting nut 110.............................................................................
Universal joint pinch bolt 25............................................................................
PAS box
Adjuster locknut 60.................................................................................
Drop arm nut 176....................................................................................
Sector shaft cover to steering box 75.....................................................
Steering box to chassis 81.....................................................................
Steering box fluid pipes 14mm thread 15...............................................
Steering box fluid pipes 16mm thread 20...............................................
Tie bar 81...............................................................................................
PAS pump
High pressure fluid pipe 20.....................................................................
Power steering pump mounting 35.........................................................
Pulley bolts, power steering pump 10....................................................
Hose clamp 3........................................................................................
Front mounting plate bolts 9..................................................................
PAS reservoir
Hose clamp 3........................................................................................
* Torque values below are for all screws and bolts used except for those that are specified otherwise.
METRIC Nm
M5 6......................................................................................................
M6 9......................................................................................................
M8 25.....................................................................................................
M10 45...................................................................................................
M12 90...................................................................................................
M14 105..................................................................................................
M16 180..................................................................................................
UNC / UNF
1/4 9......................................................................................................
5/16 24...................................................................................................
3/8 39.....................................................................................................
7/16 78...................................................................................................
1/2 90.....................................................................................................
5/8 136....................................................................................................