atf LEXUS ES300 2005 Service Manual
[x] Cancel search | Manufacturer: LEXUS, Model Year: 2005, Model line: ES300, Model: LEXUS ES300 2005Pages: 969, PDF Size: 24.08 MB
Page 168 of 969
C56360
D03824
D03705
D26465
O-ring
D26465
O-ring
40-96
- AUTOMATIC TRANSMISSION / TRANSUNDERDRIVE CLUTCH ASSY (U151E/U151F)
120 Author: Date:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
(d) Remove the return spring from the underdrive clutch
drum.
7. INSPECT UNDERDRIVE CLUTCH RETURN SPRING
SUB-ASSY
(a) Using a vernier calipers, measure the free length of the
spring together with the spring seat.
Standard free length: 17.14 mm (0.6752 in.)
8. REMOVE UNDERDRIVE CLUTCH PISTON SET
(a) Install the underdrive clutch to the transaxle case.
NOTICE:
Be careful not to damage the oil seal ring.
(b) Holding the underdrive clutch piston by hand, apply com-
pressed air (392 kPa, 4.0 kgf/cm
2, 57 psi) to the transaxle
case to remove the underdrive clutch piston.
9. REMOVE UNDERDRIVE CLUTCH DRUM O-RING
(a) Using a screwdriver, remove the O-ring from the under-
drive clutch drum.
10. INSTALL UNDERDRIVE CLUTCH DRUM O-RING
(a) Apply the new O-ring with ATF, install it to the underdrive
clutch drum.
NOTICE:
Assemble the O-ring carefully not to have a twist and a
pinching.
Page 169 of 969
D03860
C56360
Underdrive
Clutch
Return
Spring
Underdrive
Clutch Drum
C56359
Clutch
Balancer
Underdrive
Clutch Drum
D03703
SST
- AUTOMATIC TRANSMISSION / TRANSUNDERDRIVE CLUTCH ASSY (U151E/U151F)
40-97
121 Author: Date:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
11. INSTALL UNDERDRIVE CLUTCH PISTON SET
(a) Coat the underdrive clutch piston with ATF, install it to the
underdrive clutch piston drum.
NOTICE:
Be careful not to damage the O-ring.
Be careful not to damage the lip seal of the piston.
12. INSTALL UNDERDRIVE CLUTCH RETURN SPRING
SUB-ASSY
(a) Install the return spring to the underdrive clutch drum.
NOTICE:
Installing the spring sub- assembly, check all of the
springs are fit in the piston correctly.
(b) Coat the clutch balancer with ATF.
(c) Install the clutch balancer to the underdrive clutch drum.
NOTICE:
Be careful not to damage the lip seal of the clutch balancer.
(d) Place SST on the clutch balancer and compress the pis-
ton return spring with a press.
SST 09350-32014 (09351-32070)
(e) Using a snap ring expander, install the snap ring to the un-
derdrive clutch drum.
(f) Be sure the end gap of the snap ring is not aligned with
the spring retainer claw.
NOTICE:
Stop the press when the spring sheet is lowered to the
place 1 - 2 mm (0.039 - 0.078 in.) from the snap ring
grove.
This prevents the spring sheet from being deformed.
Do not expand the snap ring excessively.
Page 170 of 969
D25592
StopperStopper
D26431
Disc
Flange
Plate
D03701
D26429
40-98
- AUTOMATIC TRANSMISSION / TRANSUNDERDRIVE CLUTCH ASSY (U151E/U151F)
122 Author: Date:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
(g) Set the end gap of the snap ring in the underdrive clutch
drum shown in the illustration.
NOTICE:
The end gap of the snap ring should not coincide with any
of the stopper.
13. INSTALL UNDERDRIVE CLUTCH DISC NO.1
(a) Apply the 4 discs with ATF.
(b) Install the 4 plates, 4 discs and flange to the underdrive
clutch drum.
NOTICE:
Be careful about the order of discs, plates and flange as-
sembly.
14. INSTALL UNDERDRIVE CLUTCH FLANGE NO.2
HOLE SNAP RING
(a) Using a screwdriver, install the underdrive clutch flange
No.2 hole snap ring.
(b) Check that the end gap of snap ring is not aligned with one
of the cutouts.
NOTICE:
The snap ring should be fixed certainly in the groove of the
drum.
15. INSPECT UNDERDRIVE PACK CLEARANCE
(a) Install the underdrive clutch to the transaxle case.
NOTICE:
Be careful not to damage the oil seal ring.
(b) Set a dial indicator as shown in the illustration.
(c) Measure the underdrive clutch piston stroke while apply-
ing and releasing compressed air (392 kPa, 4.0 kgf/cm
2,
57 psi).
Park clearance: 1.51 - 1.71 mm (0.0594 - 0.0673 in.)
If the pack clearance is less than the minimum, parts may have
been assembled incorrectly, so check and reassemble again.
If the pack clearance is not within standard, select another
flange.
HINT:
There are 5 flanges in different thickness.
Flange thickness: mm (in.)
MarkThicknessMarkThickness
13.0 (0.118)43.1 (0.122)
23.2 (0.126)53.3 (0.130)
33.4 (0.134)--
Page 181 of 969
C50242
Front Differential
Side Gear
Front
Differential
Side Gear
D25599
SST
D25600
SST
C50242
Front Differential
Side Gear
Front
Differential
Side Gear
C50241
Differential Case
Front Differential Pinion Shaft No.1
- AUTOMATIC TRANSMISSION / TRANSFRONT DIFFERENTIAL ASSY (U151E)
40-109
133 Author: Date:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
6. REMOVE FRONT DIFFERENTIAL SIDE GEAR
(a) Remove the 2 front differential pinions, 2 pinion thrust
washers, 2 front differential side gears and 2 side gear
thrust washers from the differential case.
7. REMOVE TRANSAXLE HOUSING OIL SEAL
(a) Using SST, remove the oil seal.
SST 09950- 70010 (09951- 07100), 09215- 00013
(09215-00471)
8. REMOVE DIFFERENTIAL SIDE BEARING RETAINER
OIL SEAL
(a) Using SST, remove the oil seal.
SST 09950-70010 (09951-07100), 09608-10010
9. INSTALL FRONT DIFFERENTIAL SIDE GEAR
(a) Apply the 2 front differential side gears, 2 side gear thrust
washers, 2 front differential pinions and 2 pinion thrust
washers with ATF and install them to the differential case.
10. INSTALL FRONT DIFFERENTIAL PINION SHAFT NO.1
(a) Apply the front differential pinion shaft No.1 with ATF,
install it to the differential case.
Page 185 of 969
D26384
D26450
Differential Assy
D25215
90 - 100 C (194 - 230 F)
D26445
Mark
- AUTOMATIC TRANSMISSION / TRANSFRONT DIFFERENTIAL ASSY (U151E)
40-1 13
137 Author: Date:
U151E, U151F A/T REPAIR MANUAL (RM1021U)Mark ThicknessMark Thickness
72.35 (0.0925)G2.80 (0.1102)
82.40 (0.0945)H2.85 (0.1122)
(f) Remove the 16 bolts and the transaxle housing.
(g) Remove the differential assy.
16. INSTALL FRONT DIFFERENTIAL RING GEAR
(a) Using ATF and heater, heat the front differential ring gear
to 90 - 110 C (194.0 - 230.0 F).
NOTICE:
Do not overheat the ring gear to 110 C (230.0 F) or more.
(b) Clean the contact surface of the front differential case.
(c) Align the match-marks, install the front differential ring
gear case quickly.
NOTICE:
Do not install the bolts while the ring gear is hot.
Page 191 of 969
D25600
SST
C50943
C50216
C50213
Differential
Case LH
Differential
Case No.2
- AUTOMATIC TRANSMISSION / TRANSFRONT DIFFERENTIAL ASSY (U151F)
40-1 19
143 Author: Date:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
7. REMOVE DIFFERENTIAL SIDE BEARING RETAINER
OIL SEAL
(a) Using SST, remove the oil seal.
SST 09950-70010 (09951-07100), 09608-10010
8. INSTALL DIFFERENTIAL CASE SUB-ASSY NO.2
(a) Coat the front differential side gear thrust washer No.1,
front differential planetary ring gear, front differential pin-
ion No.2, front differential pinion thrust washer No.2, front
differential pinion shaft holder, front differential pinion
shaft and 2 differential pinion shafts with ATF, install them
to the differential case No.2.
(b) Using a dial indicator, measure the backlash of one pinion
gear while holding the front differential side gear toward
the case.
Standard backlash:
0.05 - 0.20 mm (0.0020 - 0.0079 in.)
NOTICE:
Do not mount the surface of front differential case which
contacts with bushing in a vise.
If the backlash is not within the specified value, refer to the table
below and select a thrust washer which will ensure that the
backlash is within the specified value.
Thrust washer thickness: mm (in.)
MarkThicknessMarkThickness
A0.95 (0.0373)F1.20 (0.0472)
B1.00 (0.0393)G1.25 (0.0492)
C1.05 (0.0413)H1.30 (0.0512)
D1.10 (0.0433)J1.35 (0.0532)
E1.15 (0.0453)K1.40 (0.0552)
(c) Engage the front differential side gear to the above men-
tioned front differential case.
(d) Install the differential case LH to the front differential case
and measure its center.
(e) After that, remove the differential case LH.
Page 198 of 969
D25215
90 - 100 C (194 - 230 F)
C50186
Match-marks
C50232
C50233
D25605
SST 40-126
- AUTOMATIC TRANSMISSION / TRANSFRONT DIFFERENTIAL ASSY (U151F)
150 Author: Date:
U151E, U151F A/T REPAIR MANUAL (RM1021U)
13. INSTALL FRONT DIFFERENTIAL RING GEAR
(a) Using ATF and heater, heat the front differential ring gear
to 90 - 110 C. (194.0 - 230.0 F)
NOTICE:
Do not overheat the ring gear to 110 C (230.0 F) or more.
(b) Clean the contact surface of the front differential case.
(c) Set the match-marks, install the front differential ring gear
case quickly.
NOTICE:
Do not install the bolts while the ring gear is hot.
(d) Temporarily install the 8 bolts as shown in the illustration.
(e) Remove the 4 bolts shown in the illustration.
(f) Temporarily install the remaining 8 set bolts.
(g) Fully tighten the set bolts.
Torque: 95.1 NVm (970 kgfVcm, 70 ftVlbf)
NOTICE:
Tighten the bolts a little at a time in diagonal order.
14. INSTALL DIFFERENTIAL SIDE BEARING RETAINER
OIL SEAL
(a) Using SST and a hammer, install a new oil seal.
SST 09223-15020, 09950-70010 (09951-07100)
(b) Coat the rip of oil seal with a little MP grease.
Page 201 of 969
400FX-04
40-2
- AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY
2517 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
AUTOMATIC TRANSAXLE ASSY
PRECAUTION
1. The automatic transaxle is composed of highly precision-finished parts, if nequine careful in-
spection before reassembly therefore even a small nick may cause fluid leakage or may de-
grade the performance. The instructions here are organized so that you work on only one com-
ponent group at a time. This will help you to avoid confusion about similar-looking parts of
different sub-assemblies being on your workbench at the same time. The component groups
are inspected and repaired from the converter housing side. Inspectio, repair and reassembly
As much as possible, before proceeding to the next component group. If a defect is found in
a certain component group during reassembly, inspect and repair this group immediately. If a
component group cannot be assembled because parts are being ordered, be sure to keep all
parts of the group in a separate container while proceeding with disassembly, inspection, re-
pair and reassembly of other component groups.
Recommended ATF: T-IV
2. All disassembled parts should be washed clean and any fluid passages and holes should be
blown with compressed air.
3. Dry all parts with compressed airnever use shop rags.
4. When using compressed air, do not aim at yourself to prevent accidentally spraying ATF or ker-
osene on your face.
5. The recommended automatic transaxle fluid or kerosene should be used for cleaning.
6. After cleaning, the parts should be arranged in the correct order for efficient inspection, repairs,
and reassembly.
7. When disassembling a valve body, be sure to match each valve together with the correspond-
ing spring.
8. New discs for the brakes and clutches that are to be used for replacement must be soaked in
ATF for at least 15 minutes before reassembly.
9. All oil seal rings, clutch discs, clutch plates, rotating parts, and sliding surfaces should be
coated with ATF prior to reassembly.
10. All gaskets and rubber O-rings should be replaced.
11. Do not apply adhesive cements to gaskets and similar parts.
12. Make sure that the ends of a snap ring are not aligned with one of the cutouts and are installed
in the groove correctly.
13. If a worn bushing is to be replaced, the sub-assembly containing the bushing must also be re-
placed.
14. Check thrust bearings and races for wear or damage. Replace if necessary.
15. Use petroleum jelly to keep parts in place.
16. When working with FIPG material, you must perform the following.
Using a razor blade and a gasket scraper, remove all the old packing (FIPG) material from the
gasket surface.
Thoroughly clean all components to remove all the loose material.
Clean both sealing surfaces with a non-residue solvent.
Parts must be reassembled within 10 minutes of application. Otherwise, the packing (FIPG) ma-
terial must be removed and reapplied.
Page 207 of 969
4010Q-02
D31337
Bearing Bracket Hole Snap Ring
32 (326, 24)
12 (122, 9)
64 (653, 47)
46 (470, 34)
Front Drive Shaft Assy RH
Transmission Control
Cable Bracket No.2
41 (418, 30)
12 (122, 9)
37 (377, 27)
5.5 (56, 49 in.Vlbf)
9.8 (100, 87 in.Vlbf)
Wire Harness
Automatic
Transmission Case
Cover
Front Drive
ShaftLH Hole
Snap Ring
Front Drive Shaft
Assy LH
Starter Assy
O-ring
Transimission Oil
Filler Tube Sub-assy
ATF Level
Gauge Oil Cooler
Outlet Tube No.1 Oil Cooler Inlet
Tube No.1Oil Cooler Tube ClampTransmission Control
Cable Bracket No.1 Flywheel Housing
Under CoverTorque Converter ClutchEngine
Mounting
Bracket FR
X6
N´m (kgf´cm, ft´lbf): Specified torque
Non-reusable partWire Harness Clamp
12 (122, 9)
12 (122, 9)
34 (350, 25)
8.4 (86, 74 in.Vlbf)
64 (653, 47)
5.4 (55, 48 in.Vlbf)
7.8 (80, 69 in.Vlbf)
13 (130, 9)
Exhaust Pipe Support Bracket
37 (377, 27)
34 (350, 25)
x 5 40-8
- AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E)
2523 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
AUTOMATIC TRANSAXLE ASSY (U151E)
COMPONENTS
Page 209 of 969
D30864
Transmission
Wire Connector
Park/neutral Position Switch Connector
Transmission Revolution
Sensor Connectors
C91736
C91737
C88047
SST
40-10
- AUTOMATIC TRANSMISSION / TRANSAUTOMATIC TRANSAXLE ASSY (U151E)
2525 Author: Date:
2005 LEXUS ES330 REPAIR MANUAL (RM1124U)
8. DISCONNECT CONNECTORS
(a) Disconnect the transmission wire connector.
(b) Disconnect the park/neutral position switch connector.
(c) Disconnect the 2 transmission revolution sensor connec-
tors.
9. REMOVE TRANSMISSION CONTROL CABLE
BRACKET NO.1
(a) Remove the bolt and oil cooler tube clamp.
(b) Remove the 2 bolts and transmission control cable brack-
et.
10. REMOVE TRANSMISSION OIL FILLER TUBE
SUB-ASSY
(a) Remove the ATF level gauge.
(b) Remove the bolt and oil filler tube.
(c) Remove the O-ring from the oil filler tube.
11. REMOVE OIL COOLER INLET TUBE NO.1
(a) Using SST and spanner, disconnect the oil cooler inlet
tube No.1.
SST 09023-12701