lock Lexus ES330 2004 Destination Input and Route Guidance / LEXUS 2004 ES330 OWNER'S MANUAL (OM33633U)

CHASSIS
387
CHECKING POWER STEERING
FLUID
Check the fluid level through the reservoir. If necessary,
add automatic transmission fluid DEXRONII or III.
If the vehicle has been driven around 80 km/h (50 mph) for 20
minutes (a little more in frigid temperatures), the fluid is hot
(60C Ð 80C or 140F Ð 175F). You may also check the
level when the fluid is cold (about room temperature, 10C Ð
30C or 50F Ð 85F) if the engine has not been run for about
five hours.

1If cold O.K.2If cold add3If hot O.K.
4If hot add
Clean all dirt off the reservoir and look at the fluid level. If the
fluid is cold, the level should be in the COLDº range. Similarly,
if it is hot, the fluid level should be in the HOTº range. If the
level is at the low side of the appropriate range, add automatic
transmission fluid DEXRON
II or III to bring the level within
the range.
To remove the reservoir cap, turn it counterclockwise and lift
up. To reinstall it, turn it clockwise. After replacing the reservoir
cap, visually check the steering box case, vane pump and hose
connections for leaks or damage.
CAUTION
The reservoir may be hot so be careful not to burn
yourself.

CHASSIS
406
NOTICE
If the wrong combination of tire and chain is used, the
chains could damage the vehicle body.
Chain installation
Install the chains on the front tires as tightly as possible.
Do not use tire chains on the rear tires. Retighten chains
after driving 0.5 Ð 1.0 km (1/4 Ð 1/2 mile).
When installing chains on your tires, carefully follow the
instructions of the chain manufacturer.
CAUTION
Do not exceed 50 km/h (30 mph) or the chain
manufacturer's recommended speed limit,
whichever is lower.
Drive carefully avoiding bumps, holes, and sharp
turns, which may cause the vehicle to bounce.
Avoid sharp turns or locked-wheel braking, as use of
chains may adversely affect vehicle handling.
When driving with chains installed, be sure to drive
carefully. Slow down before entering curves to avoid
losing control of the vehicle. Otherwise an accident
may occur.
REPLACING WHEELS
When to replace your wheels
If you have wheel damage such as bending, cracks or
heavy corrosion, the wheel should be replaced.
If you fail to replace a damaged wheel, the tire may slip off the
wheel or cause loss of handling control.
Replacement with used wheels is not recommended as they
may have been subjected to rough treatment or high mileage
and could fail without warning. Also, bent wheels which have
been straightened may have hidden structural damage and
therefore should not be used. Never use an inner tube in a
leaking wheel which is designed for a tubeless tire.

ELECTRICAL COMPONENTS
413
No.FUSEAMPERECIRCUIT
1A/F25Multiport fuel injection
system/sequential multiport
fuel injection system
2DOOR125
Multiplex communication
system (power door lock
system, auto- door locking
system, wireless remote
control system)
3TEL5No circuit
4AM230All components in IGNº and
IG2º fuses and starting system
5EFI20Multiport fuel injection
system/sequential multiport
fuel injection system
6ALT-S5Charging system
7HEAD LH
UPR10Left- hand headlight (high
beam)
No.FUSEAMPERECIRCUIT
8ETCS10Multiport fuel injection
system/sequential multiport
fuel injection system
9HORN10Horns
10IGN15Starting system
11HEAD RH
UPR10Right- hand headlight (high
beam)
12HAZ15Emergency flashers

ELECTRICAL COMPONENTS
415
No.FUSEAMPERECIRCUIT
18ABS No.240
Anti- lock brake system,
vehicle stability control system,
traction control system, brake
assist system
19MAIN40
All components in HEAD LH
LWRº, HEAD RH LWRº, HEAD
LH UPRº, HEAD RH UPRº and
DRLº fuses
20ABS No.330
Anti- lock brake system,
vehicle stability control system,
traction control system, brake
assist system
21HTR50Air conditioning system
22RDI30Electric cooling fan
23SPARE5Spare fuse
24SPARE10Spare fuse
25ABS NO.150
All components in RDI FANº,
ABS No.2º, ABS No.3º, CDSº,
HTR (50 A)º and ADJ PDLº
fuses and anti- lock brake
system, vehicle stability control
system, traction control
system, brake assist system

ELECTRICAL COMPONENTS
417
No.FUSEAMPERECIRCUIT
32ECU-B10
Multiplex communication
system (power door lock
system, security system,
auto- door locking system,
automatic light control system,
headlight delay off system, tail
light auto cut system,
illuminated entry system,
daytime running light system,
wireless remote control
system) air conditioning
system, electronic modulated
suspension, driving position
memory system
33DOME7.5
Ignition switch light, interior
light, personal lights, foot
lights, door courtesy lights,
trunk light, vanity lights, garage
door opener, clock, outside
temperature gauge,
multi- information display
34CIG15Cigarette lighter
35ECU-
ACC5
Power rear view mirrors, clock,
multi- information display,
driving position memory
system
No.FUSEAMPERECIRCUIT
36RAD NO.210Car audio system, navigation
system
37POWER
POINT15Power outlet

ELECTRICAL COMPONENTS
418
38RAD NO.120Car audio system, navigation
system
39GAUGE110
Gauges and meters, clock,
outside temperature gauge,
multi- information display, shift
lock system
40ECU-IG10
SRS airbag system, power
windows, anti- lock brake
system, electronic modulated
suspension, driving position
memory system
41WIPER25Windshield wipers
42HTR10Air conditioning system
43MIR
HTR10Outside rear view mirror
heaters

ELECTRICAL COMPONENTS
419
No.FUSEAMPERECIRCUIT
44AM15Starting system
45FOG15Front fog lights
46SUN-
SHADE15Rear sunshade
47GAUGE210
Auto anti- glare inside rear
view mirror, compass, back- up
lights, automatic light control
system, automatic headlight
leveling system, cruise control
system, seat belt reminder
lights
48PANEL10
Glove box light, console box
light, clock, outside
temperature gauge,
multi- information display,
instrument cluster lights,
instrument panel lights
49TAIL10Tail lights, parking lights,
license plate lights
50PWR NO.420Rear passenger's power
window (left side)
No.FUSEAMPERECIRCUIT
51PWR NO.220Front passenger's door lock
system, front passenger's
power window
52OBD7.5On- board diagnosis system
53SEAT
HTR20Seat heaters

ELECTRICAL COMPONENTS
420
54WASHER15Windshield washer
55FA N
RLY10Electric cooling fans
56STOP15Stop lights, high mounted
stoplight
57FUEL
OPEN5Fuel filler door opener
58DOOR
NO.225
Multiplex communication
system (power door lock
system, auto- door locking
system, wireless remote
control system)
59AMP25Car audio system
60PWR NO.320Rear passenger's power
window (right side)
No.FUSEAMPERECIRCUIT
61PWR
SEAT30Power seats, driving position
memory system
62PWR NO.130Driver's door lock system,
driver's power window, electric
moon roof
63DEF40Rear window defogger

BODY
445 3. Rinse thoroughly Ð dried soap can cause streaking. In hot
weather you may need to rinse each section right after you
wash it.
4. To prevent water spots, dry the vehicle using a clean soft
cotton towel. Do not rub or press hard Ð you might scratch the
paint.
Automatic car wash
Your vehicle may be washed in an automatic car wash, but
remember that the paint can be scratched by some types of
brushes, unfiltered washing water, or the washing process
itself. Scratching reduces paint durability and gloss, especially
on darker colors. The manager of the car wash should be able
to advise you whether the process is safe for the paint on your
vehicle.
Waxing your Lexus
Polishing and waxing is recommended to maintain the
original beauty of your Lexus' finish.
Apply wax once a month or if the vehicle surface does not repel
water well.
1. Always wash and dry the vehicle before you begin waxing,
even if you are using a combined cleaner and wax.
2. Use a good quality polish and wax. If the finish has become
extremely weathered, use a car-cleaning polish, followed by
a separate wax. Carefully follow the manufacturer's
instructions and precautions. Be sure to polish and wax the
chrome trim as well as the paint.3. Wax the vehicle again when water does not bead but
remains on the surface in large patches.
Windshield washer nozzles: Make sure that the nozzles do
not become blocked when waxing. If a nozzle becomes
blocked, contact your Lexus dealer to have the vehicle
serviced.

BODY
446
NOTICE
If a nozzle becomes blocked, do not try to clear it with
a pin or other object. The nozzle will be damaged.