engine Lexus IS220d 2012 Owner's Manual

536
6-1. Specifications
IS250/220d/200d_EEEngine number
The engine number is stamped on the engine block as shown.
IS250
IS220d and IS200d

537
6-1. Specifications
6
Vehicle specifica-
IS250/220d/200d_EE
Engine
Model4GR-FSE2AD-FHV, 2AD-FTV
Ty p e6-cylinder V type,
4-cycle, gasoline4 cylinder in line, 4
cycle, diesel
(with turbocharger)
Bore and stroke83.0  77.0 mm
(3.27 3.03 in.)86.0  96.0 mm
(3.39 3.78 in.)
Displacement2500 cm3
(152.5 cu.in.)2231 cm3
(136.1 cu.in.)
Drive belt tensionAutomatic adjustment

539
6-1. Specifications
6
Vehicle specifica-
IS250/220d/200d_EE
Lubrication system
IS250
*: The engine oil capacity is a reference quantity to be used when changing
the engine oil. Warm up and turn off the engine, wait more than 5 min-
utes, and check the oil level on the dipstick.
Engine oil selection
“Toyota Genuine Motor Oil” is used in your Lexus vehicle. Lexus
recommends the use of approved “Toyota Genuine Motor Oil”.
Another motor oil of matching quality can also be used.
Oil grade:
0W-20, 5W-20, 5W-30 and 10W-30:
API grade SL “Energy-Conserving”, SM “Energy-Conserving”,
SN “Resource-Conserving” or ILSAC multigrade engine oil
15W-40 and 20W-50:
API grade SL, SM or SN multigrade engine oil
Oil capacity
(Drain and refill 
reference*)
With filter
Without filter
6.3 L (6.6 qt., 5.5 Imp. qt.)
5.9 L (6.2 qt., 5.2 Imp. qt.)

540
6-1. Specifications
IS250/220d/200d_EERecommended viscosity (SAE):
SAE 0W-20 is filled into your
Lexus vehicle at manufactur-
ing, and the best choice for
good fuel economy and good
starting in cold weather.
If SAE 0W-20 oil is not avail-
able, SAE 5W-30 oil may be
used. However, it should be
replaced with SAE 0W-20 at
the next oil change.
If you use SAE 10W-30 or a
higher viscosity engine oil in
extremely low temperatures,
the engine may become diffi-
cult to start, so SAE 5W-30 or
lower viscosity engine oil is
recommended.
Oil viscosity (0W-20 is explained here as an example):
• The 0W in 0W-20 indicates the characteristic of the oil which
allows cold startability. Oils with a lower value before the W allow
for easier starting of the engine in cold weather.
• The 20 in 0W-20 indicates the viscosity characteristic of the oil
when the oil is at high temperature. An oil with a higher viscosity
(one with a higher value) may be better suited if the vehicle is oper-
ated at high speeds, or under extreme load conditions.
Temperature range anticipated
before next oil change.
Preferred

542
6-1. Specifications
IS250/220d/200d_EEIS220d and IS200d
*: The engine oil capacity is a reference quantity to be used when changing
the engine oil. Warm up and turn off the engine, wait more than 5 min-
utes, and check the oil level on the dipstick.
Engine oil selection
“Toyota Genuine Motor Oil” is used in your Lexus vehicle. Lexus
recommends the use of approved “Toyota Genuine Motor Oil”.
Another motor oil of matching quality can also be used.
Oil grade: ACEA C2
Oil capacity
(Drain and refill 
reference*)
With filter
Without filter
6.0 L (6.3 qt., 5.3 Imp. qt.)
5.2 L (5.5 qt., 4.6 Imp. qt.)
NOTICE
Using engine oil other than ACEA C2 may damage the catalytic converter.

543
6-1. Specifications
6
Vehicle specifica-
IS250/220d/200d_EERecommended viscosity (SAE):
SAE 0W-30 is filled into your
Lexus vehicle at manufactur-
ing, and the best choice for
good fuel economy and good
starting in cold weather.
Oil viscosity (0W-30 is explained here as an example):
• The 0W in 0W-30 indicates the characteristic of the oil which
allows cold startability. Oils with a lower value before the W allow
for easier starting of the engine in cold weather.
• The 30 in 0W-30 indicates the viscosity characteristic of the oil
when the oil is at high temperature. An oil with a higher viscosity
(one with a higher value) may be better suited if the vehicle is oper-
ated at high speeds, or under extreme load conditions.
Temperature range anticipated
before next oil change.

544
6-1. Specifications
IS250/220d/200d_EE
Cooling system
Ignition system (IS250 only)
Capacity
IS250
10.3 L (10.9 qt., 9.1 Imp. qt.)
IS220d (without power heater)
8.8 L (9.3 qt., 7.7 Imp. qt.)
IS200d (without power heater)
8.7 L (9.2 qt., 7.7 Imp. qt.)
IS220d and IS200d (with power heater)
9.0 L (9.5 qt., 7.9 Imp. qt.)
Coolant type
Use either of the following.
• “Toyota Super Long Life Coolant”
• Similar high-quality ethylene glycol-based
non-silicate, non-amine, non-nitrite, and non-
borate coolant with long-life hybrid organic
acid technology
Do not use plain water alone.
Spark plug
Make
GapDENSO FK20HBR11
1.1 mm (0.043 in.)
NOTICE
Iridium-tipped spark plugs
Use only iridium-tipped spark plugs. Do not adjust gap when tuning the
engine.

547
6-1. Specifications
6
Vehicle specifica-
IS250/220d/200d_EE
Brakes
*1:Minimum pedal clearance when depressed with a force of 490 N (50
kgf, 110 lbf) while the engine is running.
*2:Parking brake pedal travel when depressed with a force of 300 N (30.6
kgf, 67.4 lbf).
*3:Parking brake lever travel when pulled up with a force of 200 N (20.4
kgf, 45.0 lbf).
Steering
Pedal clearance *1
IS250
Right-hand drive
Left-hand drive
IS220d and IS200d
Right-hand drive
Left-hand drive
104.0 mm (4.1 in.) Min.
108.0 mm (4.3 in.) Min.
108.0 mm (4.3 in.) Min.
103.0 mm (4.1 in.) Min.
Pedal free play1.0  2.0 mm (0.04  0.08 in.)
Parking brake pedal travel *2/
lever travel *3
Pedal type
Lever type7  9 clicks
5  7 clicks
Fluid typeSAE J1703 or FMVSS No. 116 DOT 3
Free playLess than 30 mm (1.2 in.)

553
6-1. Specifications
6
Vehicle specifica-
IS250/220d/200d_EE
Fuel information
IS250
EU area:
Your vehicle must use only
unleaded gasoline conforming to
European standard EN228.
For optimum engine perfor-
mance, select unleaded gasoline
with a Research Octane Number
of 95 or higher.
Except EU area:
Your vehicle must use only
unleaded gasoline.
For optimum engine perfor-
mance, select unleaded gasoline
with a Research Octane Number
of 95 or higher.
IS220d and IS200d
EU area:
Your vehicle must use only diesel
fuel conforming to European
standard EN590.
Except EU area:
Your vehicle must use only diesel
fuel that contains 50 ppm or less
of sulfur and has a cetane number
of 48 or higher.

554
6-1. Specifications
IS250/220d/200d_EE
Fuel tank opening for unleaded gasoline (IS250)
To help prevent incorrect fueling, your Lexus has a fuel tank opening that
only accommodates the special nozzle on unleaded fuel pumps.
If you plan to drive in foreign countries (IS220d and IS200d)
Low sulphur diesel fuel may not be available, so please confirm the avail-
ability with your distributor.
If premium gasoline is not available (IS250)
If this premium type cannot be obtained, you can temporarily use unleaded
gasoline with a Research Octane Number as low as 91.
If your engine knocks
Consult any authorized Lexus dealer or repairer, or another duly quali-
fied and equipped professional.
You may occasionally notice light knocking for a short time while accel-
erating or driving uphill. This is normal and there is no need for concern.