stop start LEXUS LS430 2005 Owner's Manual

STARTING AND DRIVING
347
The vehicle
−to− vehicle distance is always set to “Long” when
the ignition switch is turned on.
CAUTION
 Select the vehicletovehicle distance
considering traffic conditions. The approximate
vehicletovehicle distance based on time
interval when driving at 88 km/h (55 mph) is
shown below :
“Long” about 75 m (about 245 ft.) . . . . . . . .
“Middle” about 50 m (about 165 ft.) . . . . . .
“Short” about 30 m (about 100 ft.) . . . . . . .
If the vehicle speed is slower than 88 km/h (55 mph),
the distance will be shorter than the above.
 During long downhill driving, the vehicletovehicle
distance will be shorter than the selected distance.
(e) Braking control
Dynamic radar/laser cruise control is not a collision avoidance
system. If an approach warning is activated, depress the brake
pedal to decelerate to ensure an appropriate
vehicle −to−vehicle distance.
31L177
 1
Under the vehicletovehicle distance control
2Braking activated
Braking control is operating only when the vehicle −to− vehicle
distance control mode is selected and your vehicle speed
exceeds about 40 km/h (25 mph).
If you are getting closer to the vehicle ahead at relatively higher
speed than those of the vehicle ahead or if engine braking
cannot be applied properly, braking control is automatically
activated. The multi− information display changes as shown in
the illustration and the stop/tail lights on your vehicle and on the
vehicle on the display come on.

STARTING AND DRIVING
353
w280
If the system cannot easily measure the
vehicletovehicle distance because of the following
conditions while the dynamic radar/laser cruise control is
on, the above message appears.
Dynamic radar cruise control—
 The driving pattern selector switch is set to the “SNOW”
mode.
 It is determined that it is difficult to make a measurement
because of bad weather (such as extremely hot weather)
 The wipers are operated at high speed with the wiper lever
in the “AUTO” position
Dynamic laser cruise control—
 The driving pattern selector switch is set to the “SNOW”
mode.
 It is determined that it is difficult to make a measurement
because of bad weather (such as rainy, foggy, or snowy
weather)
 The wipers are operated at high or low speeds with the
wiper lever in the “AUTO” position.
 Direct sunlight from the front In the following
cases, the dynamic radar/laser cruise
control switches to the “RADAR READY” mode:
Dynamic radar cruise control—
 The driving pattern selector switch is changed to the
“normal” or “power” position.
 The wipers are stopped or are switched to low speed or
intermittent operation. (Including intermittent and stopped
wipers in the “AUTO” position)
In the above conditions, press the control lever upward in the
“+ RES” direction and release it. The dynamic radar cruise
control will be restored, however, even after the weather
clears, if the setting operation cannot be performed or if the
warning message still appears, the system might have
malfunctioned. Although it is no problem to continue driving,
contact your Lexus dealer.

STARTING AND DRIVING
354Dynamic laser cruise control—

The driving pattern selector switch is changed to the
“normal” or “power” position.
 The wipers are stopped or are switched to intermittent
operation. (Including intermittent and stopped wipers in the
“AUTO” position)
 No direct sunlight from the front
In the above conditions, press the control lever upward in the
“+ RES” direction and release it. The dynamic laser cruise
control will be restored, however, even after the weather
clears, if the setting operation cannot be performed or if the
warning message still appears, the system might have
malfunctioned. Although it is no problem to continue driving,
contact your Lexus dealer.
w281
If the system malfunction is detected when dynamic
radar/laser cruise control is in the “RADAR READY” mode
or operating, the above message appears.
If this message appears, stop your vehicle in a safe place, turn
the ignition off, and then restart it to reset the system. If the
setting still cannot be made or the same message appears
again, the system might have malfunctioned. Although it is no
problem to continue driving, contact your Lexus dealer.
NOTICE
While you are cruising with the dynamic radar/laser
cruise control on, if the master warning light comes on,
the cruise indicator light flashes, “Check Cruise
System” appears on the multiinformation display and
the warning tone sounds, turn the ignition switch off
and then on again. If the function is cancelled again
after setting or if settings cannot be made, the dynamic
radar/laser cruise control system may be
malfunctioning. Although it is no problem to continue
driving, have your vehicle checked by your Lexus
dealer.

STARTING AND DRIVING
366
“Check VSC” warning message
31L337a
If the vehicle stability control system or the traction
control system malfunctions, the master warning light
and “TRAC OFF” indicator light come on. At this time a
warning tone sounds and the above message appears.
If the message appears, the vehicle stability control system
and traction control system do not work. Although it is no
problem to continue driving, have your vehicle checked by
your Lexus dealer as soon as possible.
BRAKE SYSTEM
The tandem master cylinder brake system is a hydraulic
system with two separate sub −systems. If either sub −system
should fail, the other will still work. However, the pedal will be
harder to press, and your stopping distance will increase. Also,
the brake system warning light may come on.
CAUTION
Do not drive your vehicle with only a single brake
system. Have your brakes fixed immediately.
Brake booster
The brake booster uses engine vacuum to power −assist the
brakes. If the engine should quit while you are driving, you can
bring the vehicle to a stop with normal pedal pressure. There
is enough reserved vacuum for one or two stops but no more!
CAUTION
 Do not pump the brake pedal if the engine stalls.
Each push on the pedal uses up your reserved
vacuum.
 Even if the power assist is completely lost, the brakes
will still work. But you will have to push the pedal
hard, much harder than normal. And your braking
distance will increase.

STARTING AND DRIVING
367
Antilock brake system
The antilock brake system is designed to automatically
help prevent lockup of the wheels during a sudden
braking or braking on slippery road surfaces. This assists
in providing directional stability and steering
performance of the vehicle under these circumstances.
Effective way to press the ABS brake pedal: When the
anti−lock brake system function is in action, you may feel the
brake pedal pulsating and hear a noise. In this situation, to
let the anti−lock brake system work for you, just hold the
brake pedal down more firmly. Do not pump the brake in a
panic stop. This will result in reduced braking performance.
The anti −lock brake system becomes operative after the
vehicle has accelerated to a speed in excess of approximately
10 km/h (6 mph). It stops operating when the vehicle
decelerates to a speed below approximately 5 km/h (3 mph).
Depressing the brake pedal on slippery road surfaces such as
on a manhole cover, a steel plate at a construction site, joints
in a bridge, etc. on a rainy day tends to activate the anti −lock
brake system.
You may hear a click or motor sound in the engine
compartment for a few seconds when the engine is started or
just after the vehicle begins to move. This means that the
anti−lock brake system is in the self− check mode, and does not
indicate a malfunction. When the antilock brake system is activated, the
following conditions may occur. They do not indicate a
malfunction of the system:

You may hear the anti− lock brake system operating and feel
the brake pedal pulsating and the vibrations of the vehicle
body and steering wheel. You may also hear the motor
sound in the engine compartment even after the vehicle is
stopped.
 At the end of the anti−lock brake system activation, the
brake pedal may move a little forward.
CAUTION
Do not overestimate the antilock brake system:
Although the antilock brake system assists in
providing vehicle control, it is still important to drive
with all due care and maintain a moderate speed and
safe distance from the vehicle in front of you, because
there are limits to the vehicle stability and effectiveness
of steering wheel operation even with the antilock
brake system on.
If tire grip performance exceeds its capability, or if
hydroplaning occurs during high speed driving in the
rain, the antilock brake system does not provide
vehicle control.

STARTING AND DRIVING
368
Antilock brake system is not designed to shorten the
stopping distance: Always drive at a moderate speed
and maintain a safe distance from the vehicle in front of
you. Compared with vehicles without an antilock
brake system, your vehicle may require a longer
stopping distance in the following cases:
Driving on rough, gravel or snowcovered roads.
 Driving with tire chains installed.
 Driving over the steps such as the joints on the road.
 Driving on roads where the road surface is pitted or
has other differences in surface height.
Install all 4 tires of specified size at appropriate
pressure: The antilock brake system detects vehicle
speeds u sing the speed sensors for respective wheels’
turning speeds. The use of tires other than specified
may fail to detect the accurate turning speed resulting
in a longer stopping distance.“ABS” warning light
31L350
 1 U.S.A. 2Canada
The light comes on when the ignition switch is turned to the
“ON” position. If the anti−lock brake system and the brake
assist system work properly, the light turns off after a few
seconds. Thereafter, if either of the systems malfunctions, the
light comes on again.
When the “ABS” warning light is on (and the brake system
warning light is off), the anti −lock brake system, the brake
assist system, the traction control system and/or the vehicle
stability control system do/does not operate, but the brake
system still operates conventionally.
When the “ABS” warning light is on (and the brake system
warning light is off), the anti− lock brake system does not
operate so that the wheels could lock up during a sudden
braking or braking on slippery road surfaces.

STARTING AND DRIVING
369
If any of the following conditions occurs, this indicates a
malfunction
somewhere in the components monitored by
the warning light system. Contact your Lexus dealer as
soon as possible to service the vehicle.
 The light does not come on when the ignition switch is
turned to the “ON” position, or remains on.
 The light comes on while you are driving.
A warning light turning on briefly during operation does not
indicate a problem.
CAUTION
If the “ABS” warning light remains on together with the
brake system warning light, immediately stop your
vehicle at a safe place and contact your Lexus dealer.
In this case, not only the antilock brake system will fail
but also the vehicle will become extremely unstable
during braking.
Drumindisc type parking brake system
Your vehicle has a drum−in−disc type parking brake system.
This type of brake system needs bedding −down of the brake
shoes periodically or whenever the parking brake shoes
and/or drums are replaced.
Have your Lexus dealer perform the bedding −down.
Brake assist system
If you slam the brakes on such as in an emergency or
apply the brakes more firmly than usual such as when
descending the hill with the designated number of
occupants in the vehicle, the brake assist system
provides more powerful braking.
If you slam the brakes on or apply the brakes more firmly, more
powerful braking will be applied. At this time, you may hear a
sound in the engine compartment and feel the vibrations of the
brake pedal. This does not indicate a malfunction.
The brake assist system becomes operative after the vehicle
has accelerated to a speed in excess of approximately 10 km/h
(6 mph). It stops operating when the vehicle decelerates to a
speed below approximately 5 km/h (3 mph).
For an explanation of this system’s warning light, see “ABS”
warning light on page 87 or 368.

STARTING AND DRIVING
370
TIRE PRESSURE WARNINGSYSTEM
The tire pressure warning system is designed to provide
warning using a message in the multiinformation
display, master warning light and warning tone when tire
inflation pressure is critically low while driving. This
message appears to inform you that such low tire
pressure may hamper driving.
As this system is not designed to operate when the vehicle is
stopped, check the tire inflation pressure regularly. The
recommended cold tire inflation pressure, tire size and the
vehicle capacity weight are on the tire and loading information
label. (For instructions, see “Checking tire inflation pressure”
on page 468.)
Installed tires should be of the specified size. They should be
of the same size and construction. If tires other than the
specified size are used, or if tires of different sizes or
constructions are mixed, the tire pressure warning system will
not function properly.
Low tire pressure warning message
w264
When the low tire inflation pressure is detected while
driving, the master warning light comes on, the above
message appears and a warning tone sounds.
If the above message appears and adjust the tire inflation
pressure to the specified level as soon as possible. Push the
tire pressure warning system reset switch for a few seconds
and make sure the warning message goes off. If the message
still remains on, have your vehicle checked by your Lexus
dealer as soon as possible.
The tire pressure warning system does not function
properly under certain circumstances. In the following
cases, the low tire pressure warning may not turn on even
if the tire inflation pressure is low, or it may turn on when
the tire inflation pressure is actually normal.
 A compact spare tire, snow tires, or tire chains are used.
 The tire inflation pressure is excessively higher than
specified, or tire inflation pressure suddenly drops due to
bursting or other causes.
 You are driving on slippery road surfaces such as rough or
frozen roads.
 You are driving under 30 km/h (19 mph) or above 100 km/h
(62 mph) for less than 5 minutes.
 The tires differ in tread pattern or manufacturer.
 The tires are not the specified size.

STARTING AND DRIVING
372
Tire pressure warning system reset switch
31L568b
The tire pressure warning system needs to be initialized
after tires or wheels are replaced or rotated.
To initialize the system, perform the following:
1. Park the vehicle at a safe place with the parking brake
applied and turn the ignition switch to “LOCK”.
2. Adjust the pressure of all the installed tires to the specified
level. (See “Tires and wheels” on pages 463 through 465.)
3. Turn the ignition switch to “ON”.
If the low tire pressure warning message “Low Tire” appears
in the multi−information display, push the reset switch for a few
seconds and make sure the warning message goes off.
4. With the vehicle stopped, push and hold the reset switch
until “Pressure Initial” appears in the multi−information display.
W266
Initialization is completed after driving at the speeds of 30
km/h (19 mph) or over for more than one hour. If the
following driving conditions are satisfied, initialization
will be completed in about one hour.
 The vehicle speeds is between 50 km/h (31 mph) and
100 km/h (62 mph).
 The roads are dry, smooth and straight.
 The number of passengers is one or two (including the
driver).
If you make a mistake in the middle of initialization, perform the
operation from the beginning again.
Do not push the reset switch without adjusting the tire inflation
pressure to the specified level. Otherwise, the low tire
pressure warning may not turn on even if the tire inflation
pressure is low, or it may turn on when the tire inflation
pressure is actually normal.
If you push the reset switch while driving, initialization is not
performed.
If “Pressure Initial”does not appear when the reset switch is
held down, the system may be malfunctioning. Have your
vehicle checked by your Lexus dealer as soon as possible.

STARTING AND DRIVING
373
Tire pressure system warning message
w265
If there is a problem electrically in the tire pressure
warning system, the master warning light comes on, the
above message appears and a warning tone sounds. At
this time the multiinformation display indicates which
part causes an error.
Although it is no problem to continue driving with the above
message on the display, have your vehicle checked by your
Lexus dealer as soon as possible.
BRAKE PAD WEAR LIMITINDICATORS
13L338
 1Master warning light
2Brake pad wear warning message
When your brake pads are worn enough to require
replacement, the warning tone sounds, the master
warning light flashes and the brake pad wear warning
message in the multiinformation display appears.
If the warning message appears while driving, have the brake
pads checked and replaced by your nearest Lexus dealer
immediately.
Continuous driving without replacing the brake pads will cause
expensive rotor damage and increasing brake pedal effort to
get the same stopping distance.