engine LEXUS RX350 2011 Workshop Manual

172
2-2. Instrument cluster
CAUTION
nIf a safety system warning light does not come on
Should a safety system light such as the ABS and SRS airbag warning light not
come on when you start the engine, this could mean that these systems are not
available to help protect you in an accident, which could result in death or serious
injury. Have the vehicle inspected by your Lexus dealer immediately if this occurs.
nWarning lights
Warning lights inform the driver of malfunctions in any of the vehi-
cle’s systems. (→P. 535)
*: These lights turn on when the “ENGINE START STOP” switch is turned
to IGNITION ON mode to indicate that a system check is being per-
formed. They will turn off after the engine is started, or after a few sec-
onds. There may be a malfunction in a system if a light does not come on,
or if the lights do not turn off. Have the vehicle inspected by your Lexus
dealer, for details.
(U.S.A.)
(Canada)
(U.S.A.)
(Canada)
(U.S.A.)

(Canada)
(if equipped) (for driver) (for front
passenger)
******
****
***

177
2-2. Instrument cluster
2

When driving
nElectronic features control can be turned on/off when
The “ENGINE START STOP” switch is in IGNITION ON mode.
nConditions for ending electronic features control
In the following situations, the electronic features control will end automatically:
lThe menu switch is pressed
lThe radar cruise control is operated
lIntuitive parking assist starts operating
lNo action is performed for some time after the electronic features control
screen is displayed
lA warning message appears after the electronic features control screen is dis-
played
nEco Driving Indicator
Eco Driving Indicator Light
During Eco-friendly acceleration (Eco
driving), Eco Driving Indicator Light will
turn on.
Eco Driving Indicator Zone Display
Suggests Eco driving range with current
Eco driving ratio based on acceleration.
Zone of Eco driving
Eco driving ratio based on acceleration
If Zone of Eco driving is exceeded, the
right of Eco Driving Indicator Zone Dis-
play will blink and Eco Driving Indicator
Light will turn off.
Eco Driving Indicator will operate when the
vehicle is being driven with the shift lever in D.
Eco Driving Indicator will not operate when
the vehicle is in ECT SNOW mode.

184
2-3. Operating the lights and windshield wipers
Headlight switch
The headlights can be operated manually or automatically.
U.S.A.
The headlights and
side marker, parking,
tail, license plate, day-
time running lights
and instrument panel
lights turn on and off
automatically (when
the “ENGINE START
STOP” switch is in
IGNITION ON
mode).
The side marker, park-
ing, tail, license plate,
daytime running lights
and instrument panel
lights turn on.
The headlights and all
the lights listed above
(except daytime run-
ning lights) turn on.
The daytime running
lights turn off.

185
2-3. Operating the lights and windshield wipers
2

When driving
Canada
The daytime running
lights turn on.
The headlights and
side marker, parking,
tail, license plate, day-
time running lights
and instrument panel
lights turn on and off
automatically (when
the “ENGINE START
STOP” switch is in
IGNITION ON
mode).
The side marker, park-
ing, tail, license plate,
daytime running lights
and instrument panel
lights turn on.
The headlights and all
the lights listed above
(except daytime run-
ning lights) turn on.

187
2-3. Operating the lights and windshield wipers
2

When driving
Press the “ENTER” switch to
change to “OFF”.
The “AFS OFF” indicator will be
displayed.
Each pressing of the switch turns
“A F S ” o n a n d o f f .
Press the menu switch to change to
the normal display.
STEP2
nDaytime running light system
lTo make your vehicle more visible to other drivers, the daytime running lights
turn on automatically whenever the engine is started and the parking brake is
released. Daytime running lights are not designed for use at night.
For the U.S.A.: Daytime running lights can be turned off by operating the switch.
lCompared to turning on the headlights, the daytime running light system offers
greater durability and consumes less electricity, so it can help improve fuel
economy.
nHeadlight control sensor
The sensor may not function properly if an
object is placed on the sensor, or anything
that blocks the sensor is affixed to the wind-
shield.
Doing so interferes with the sensor detecting
the level of ambient light and may cause the
automatic headlight system to malfunction.

188
2-3. Operating the lights and windshield wipers
nAutomatic light off system
lWhen the headlights come on: The headlights and tail lights turn off 30 seconds
after a door is opened and closed if the “ENGINE START STOP” switch is
turned to ACCESSORY mode or turned off. (The lights turn off immediately
if on the key is pressed after all the doors are locked.)
lWhen only the tail lights come on: The tail lights turn off automatically if the
“ENGINE START STOP” switch is turned to ACCESSORY mode or turned off
and the driver’s door is opened.
To turn the lights on again, turn the “ENGINE START STOP” switch to IGNITION
ON mode, or turn the light switch off once and then back to or .
nAutomatic headlight leveling system (if equipped)
The level of the headlights is automatically adjusted according to the number of
passengers and the loading condition of the vehicle to ensure that the headlights do
not interfere with other road users.
nIf the “AFS OFF” indicator flashes
It may indicate a malfunction in the system. Contact your Lexus dealer.
nCustomization
Settings (e.g. light sensor sensitivity) can be changed.
(Customizable features →P. 6 2 1 )
NOTICE
nTo prevent the battery discharge
Do not leave the lights on longer than necessary when the engine is not running.

191
2-3. Operating the lights and windshield wipers
2

When driving
nThe Automatic High Beam can be operated when
The “ENGINE START STOP” switch is IGNITION ON mode.
nLimitations of the Automatic High Beam
Do not rely on the Automatic High Beam. Always drive safely, taking care to
observe your surroundings and turning high beam on or off manually if necessary.
nCamera sensor detection information
lHigh beam may not be automatically turned off in the following situations:

193
2-3. Operating the lights and windshield wipers
2

When driving
nIf the Automatic High Beam indicator flashes
It may indicate a malfunction in the system. Contact your Lexus dealer.
nTemporary lowering sensor sensitivity
The sensitivity of the sensor can be temporarily lowered.
To lower the sensitivity, push and hold the “AUTO” button on the inside rear view
mirror for 15 to 20 seconds, and release. The indicator light on the inside rear view
mirror will flash to indicate that the sensitivity has been lowered.
When the “ENGINE START STOP” switch is turned off, the sensitivity will be
returned to its normal level.
nCustomization that can be configured at your Lexus dealer
The Automatic High Beam can be turned off.

199
2-3. Operating the lights and windshield wipers
2

When driving
nThe windshield wipers and washer can be operated when
The “ENGINE START STOP” switch is in IGNITION ON mode.
nEffects of vehicle speed on wiper operation
Vehicle speed affects the following even when the wipers are not in “AUTO” mode:
lIntermittent wiper interval
lWiper operation when the washer is being used (delay until drip prevention
wiper sweep occurs)
When low speed wiper operation is selected, wiper operation will be switched from
low speed to intermittent wiper operation only when the vehicle is stationary.
(However, when the sensor sensitivity is adjusted to the highest, the mode cannot
be switched.)
Sensor sensitivity (high)
Sensor sensitivity (low)
Washer/wiper dual operation
The wipers will automatically
operate a couple of times after
the washer squirts.
(After operating several times,
the wipers operate one more
time after a short delay to pre-
vent dripping.)
If the headlights are on, the
headlight cleaners will operate
once.

200
2-3. Operating the lights and windshield wipers
nRaindrop sensor (vehicles with rain-sensing windshield wipers)
lIf the wiper switch is turned to the position while the “ENGINE START
STOP” switch is in IGNITION ON mode, the wipers will operate once to show
that “AUTO” mode is activated.
lWhen the sensor sensitivity ring is turned toward high while in “AUTO” mode,
the wipers will operate once to indicate that the sensor sensitivity is enhanced.
lIf the temperature of the raindrop sensor is 194°F (90°C) or higher, or 5°F
(-15°C) or lower, automatic operation may not occur. In this case, operate
the wipers in any mode other than “AUTO”.
nIf no windshield washer fluid sprays
Check that the washer nozzles are not blocked if there is washer fluid in the wind-
shield washer fluid reservoir.
CAUTION
nCaution regarding the use of windshield wipers in “AUTO” mode (vehicles with
rain-sensing windshield wipers)
The windshield wipers may operate unexpectedly if the sensor is touched or the
windshield is subject to vibration in “AUTO” mode. Take care that your fingers or
anything else do not become caught in the windshield wipers.
lThe raindrop sensor judges the amount
of raindrops.
An optical sensor is adopted. It may not
operate properly when sunlight from the
rising or setting of the sun intermittently
strikes the windshield, or if bugs etc. are
present on the windshield.