wiring MAZDA 6 2002 Suplement Service Manual

ON-BOARD DIAGNOSTIC
F2–111
F2
DTC P0117A6E407001082214
Diagnostic procedure
DTC P0117 ECT sensor circuit low input
DETECTION
CONDITION•PCM monitors input voltage from ECT sensor while engine is running. If input voltage from ECT sensor is
below 0.1 V, PCM determines ECT sensor circuit low input.
POSSIBLE
CAUSE•ECT sensor malfunction
•Connector or terminal malfunction
•Short to GND in wiring between ECT sensor terminal A and PCM terminal 87
•ECT sensor signal and GND circuits short each other
•PCM malfunction
ECT SENSOR
A
B
562
546287
91
B
APCM
91
87 ECT SENSOR
HARNESS SIDE CONNECTORPCM
HARNESS SIDE CONNECTOR
STEP INSPECTION ACTION
1PERFORM DTC CONFIRMATION PROCEDURE
•Perform “DTC Confirmation Procedure”.
(See F2–85 DTC CONFIRMATION
PROCEDURE)
•Is same DTC present during KOEO or KOER
self-test?Yes Go to next step.
No Intermittent concern exists. Go to “Intermittent Concern
Troubleshooting”.
(See F2–227 INTERMITTENT CONCERN
TROUBLESHOOTING)
2INSPECT POOR CONNECTION OF ECT
SENSOR CONNECTOR
•Turn engine switch to OFF.
•Inspect for poor connection (damaged, pulled-
out terminals, corrosion, etc.).
•Is there any malfunction?Yes Repair or replace suspected terminal, go to Step 7.
No Go to next step.
3CLASSIFY ECT SENSOR MALFUNCTION OR
HARNESS MALFUNCTION
•Turn engine switch to ON (Engine OFF).
•Disconnect ECT sensor connector.
•Access ECT PID using WDS or equivalent.
•Is ECT PID below 0.1 V?Yes Go to next step.
No Replace ECT sensor, go to Step 7.
(See F2–76 ENGINE COOLANT TEMPERATURE (ECT)
SENSOR REMOVAL/INSTALLATION)
4INSPECT ECT SENSOR SIGNAL CIRCUIT FOR
SHORT TO GND
•Turn engine switch to OFF.
•Inspect continuity between ECT sensor
terminal A and body GND.
•Is there continuity?Yes Repair or replace harness for short to GND, go to Step 7.
No Go to next step.

ON-BOARD DIAGNOSTIC
F2–113
F2
DTC P0118A6E407001082215
Diagnostic procedure
DTC P0118 ECT sensor circuit high input
DETECTION
CONDITION•PCM monitors input voltage from ECT sensor while engine is running. If input voltage from ECT sensor is
above 5.0 V, PCM determines ECT sensor circuit high input.
POSSIBLE
CAUSE•ECT sensor malfunction
•Connector or terminal malfunction
•Short to power circuit in wiring between ECT sensor terminal A and PCM terminal 87
•Open circuit in wiring between ECT sensor terminal A and PCM terminal 87
•Open circuit in wiring between ECT sensor terminal B and PCM terminal 91
•PCM malfunction
STEP INSPECTION ACTION
1PERFORM DTC CONFIRMATION PROCEDURE
•Perform “DTC Confirmation Procedure”.
(See F2–85 DTC CONFIRMATION
PROCEDURE)
•Is same DTC present during KOEO or KOER
self-test?Yes Go to next step.
No Intermittent concern exists. Go to “Intermittent Concern
Troubleshooting”.
(See F2–227 INTERMITTENT CONCERN
TROUBLESHOOTING)
2INSPECT POOR CONNECTION OF ECT
SENSOR CONNECTOR
•Turn engine switch to OFF.
•Inspect for poor connection (damaged, pulled-
out terminals, corrosion, etc.).
•Is there any malfunction?Yes Repair or replace suspected terminal, go to Step 7.
No Go to next step.
3CLASSIFY ECT SENSOR MALFUNCTION OR
HARNESS MALFUNCTION
•Turn engine switch to ON (Engine OFF).
•Connect jumper wire between ECT sensor
connector terminals.
•Access ECT PID using WDS or equivalent.
•Is ECT PID below 1.0 V?Yes Replace ECT sensor, go to Step 7.
(See F2–76 ENGINE COOLANT TEMPERATURE (ECT)
SENSOR REMOVAL/INSTALLATION)
No Go to next step.
562
5462
ECT SENSOR
A
BPCM
87
91
B
A
9187 ECT SENSOR
HARNESS SIDE CONNECTORPCM
HARNESS SIDE CONNECTOR

F2–116
ON-BOARD DIAGNOSTIC
End Of Sie
DTC P0122A6E407001082217
5INSPECT POOR CONNECTION OF PCM
CONNECTOR
•Turn engine switch to OFF.
•Inspect for poor connection (damaged, pulled-
out terminals, corrosion, etc.).
•Is there any malfunction?Yes Repair or replace suspected terminal, go to next step.
No Go to next step.
6VERIFY TROUBLESHOOTING OF DTC P0121
COMPLETED
•Make sure to reconnect all disconnected
connectors.
•Clear DTC from PCM memory using WDS or
equivalent.
•Start engine.
•Is same DTC present?Yes Replace PCM, go to next step.
(See F2–64 PCM REMOVAL/INSTALLATION)
No Go to next step.
7VERIFY AFTER REPAIR PROCEDURE
•Perform “After Repair Procedure”.
(See F2–86 AFTER REPAIR PROCEDURE)
•Is there any DTC present?Yes Go to applicable DTC inspection.
(See F2–87 DTC TABLE)
No Troubleshooting completed. STEP INSPECTION ACTION
DTC P0122 Accelerator position sensor No.1 circuit low input
DETECTION
CONDITION•PCM monitors input voltage from accelerator position sensor No.1 while engine is running. If input voltage
from accelerator position sensor No.1 is below 0.3 V, PCM determines accelerator position sensor No.1
circuit low input.
POSSIBLE
CAUSE•Accelerator position sensor No.1 malfunction
•Connector or terminal malfunction
•Open circuit in wiring between accelerator position sensor terminal A and PCM terminal 90
•Short to GND in wiring between accelerator position sensor terminal B and PCM terminal 10
•Accelerator position sensor No.1 signal and GND circuits short each other
•PCM malfunction
ACCELERATOR POSITION SENSOR NO.1
A
B
D90
10
91PCM
DCB
A
91
9010
7
54
3
6
2
2
25
7
7
ACCELERATOR POSITION SENSOR
HARNESS SIDE CONNECTORPCM
HARNESS SIDE CONNECTOR

F2–118
ON-BOARD DIAGNOSTIC
DTC P0123A6E407001082218
Diagnostic procedure
DTC P0123 Accelerator position sensor No.1 circuit high input
DETECTION
CONDITION•PCM monitors input voltage from accelerator position sensor No.1 while engine is running. If input voltage
from accelerator position sensor No.1 is above 4.7 V, PCM determines accelerator position sensor No.1
circuit high input.
POSSIBLE
CAUSE•Accelerator position sensor No.1 malfunction
•Connector or terminal malfunction
•Accelerator position sensor No.1 power and signal circuits short each other
•Open circuit in wiring between accelerator position sensor terminal B and PCM terminal 10
•Open circuit in wiring between accelerator position sensor terminal D and PCM terminal 91
•PCM malfunction
STEP INSPECTION ACTION
1PERFORM DTC CONFIRMATION PROCEDURE
•Perform “DTC Confirmation Procedure”.
(See F2–85 DTC CONFIRMATION
PROCEDURE)
•Is same DTC present during KOEO or KOER
self-test?Yes Go to next step.
No Intermittent concern exists. Go to “Intermittent Concern
Troubleshooting”.
(See F2–227 INTERMITTENT CONCERN
TROUBLESHOOTING)
52
53
6
25
4
3
62
ACCELERATOR POSITION SENSOR NO.1
A
B
D90
10
91PCM
9190
10 DC
B
APCM
HARNESS SIDE CONNECTOR ACCELERATOR POSITION SENSOR
HARNESS SIDE CONNECTOR

F2–120
ON-BOARD DIAGNOSTIC
DTC P0182A6E407001082219
Diagnostic procedure
DTC P0182 Fuel temperature sensor circuit low input
DETECTION
CONDITION•PCM monitors input voltage from fuel temperature sensor while engine is running. If input voltage from fuel
temperature sensor is below 0.1 V, PCM determines fuel temperature sensor circuit low input.
POSSIBLE
CAUSE•Fuel temperature sensor malfunction
•Connector or terminal malfunction
•Short to GND in wiring between fuel temperature sensor terminal A and PCM terminal 35
•Fuel temperature sensor signal and GND circuits short each other
•PCM malfunction
FUEL TEMPERATURE SENSOR
462
5
4362A
B35
91PCM
BA
9135 FUEL TEMPERATURE SENSOR
HARNESS SIDE CONNECTORPCM
HARNESS SIDE CONNECTOR
STEP INSPECTION ACTION
1VERIFY RELATED REPAIR INFORMATION
AVAILABILITY
•Check for related Service Information
availability.
•Is any related repair information available?Yes Perform repair or diagnosis according to available Service
Information.
•If vehicle is not repaired, go to next step.
No Go to next step.

F2–122
ON-BOARD DIAGNOSTIC
DTC P0183A6E407001082220
Diagnostic procedure
DTC P0183 Fuel temperature sensor circuit high input
DETECTION
CONDITION•PCM monitors input voltage from fuel temperature sensor while engine is running. If input voltage from fuel
temperature sensor is above 5.0 V, PCM determines fuel temperature sensor circuit high input.
POSSIBLE
CAUSE•Fuel temperature sensor malfunction
•Connector or terminal malfunction
•Short to power circuit in wiring between fuel temperature sensor terminal A and PCM terminal 35
•Open circuit in wiring between fuel temperature sensor terminal A and PCM terminal 35
•Open circuit in wiring between fuel temperature sensor terminal B and PCM terminal 91
•PCM malfunction
STEP INSPECTION ACTION
1VERIFY RELATED REPAIR INFORMATION
AVAILABILITY
•Check for related Service Information
availability.
•Is any related repair information available?Yes Perform repair or diagnosis according to available Service
Information.
•If vehicle is not repaired, go to next step.
No Go to next step.
52
5
4
32
6
6
FUEL TEMPERATURE SENSOR
A
B35
91PCM
BA
FUEL TEMPERATURE SENSOR
HARNESS SIDE CONNECTORPCM
HARNESS SIDE CONNECTOR
35
91

ON-BOARD DIAGNOSTIC
F2–125
F2
DTC P0192A6E407001082222
Diagnostic procedure
DTC P0192 Fuel pressure sensor circuit low input
DETECTION
CONDITION•PCM monitors input voltage from fuel pressure sensor while engine is running. If input voltage from fuel
pressure sensor is below 0.4 V, PCM determines fuel pressure sensor circuit low input.
POSSIBLE
CAUSE•Fuel pressure sensor malfunction
•Connector or terminal malfunction
•Short to GND in wiring between fuel pressure sensor terminal C and PCM terminal 90
•Open circuit in wiring between fuel pressure sensor terminal C and PCM terminal 90
•Short to GND in wiring between fuel pressure sensor terminal B and PCM terminal 61
•Fuel pressure sensor signal and GND circuits short each other
•PCM malfunction
STEP INSPECTION ACTION
1VERIFY RELATED REPAIR INFORMATION
AVAILABILITY
•Check for related Service Information
availability.
•Is any related repair information available?Yes Perform repair or diagnosis according to available Service
Information.
•If vehicle is not repaired, go to next step.
No Go to next step.
2INSPECT POOR CONNECTION OF FUEL
PRESSURE SENSOR CONNECTOR
•Turn engine switch to OFF.
•Inspect for poor connection (damaged, pulled-
out terminals, corrosion, etc.).
•Is there any malfunction?Yes Repair or replace suspected terminal, go to Step 9.
No Go to next step.
3INSPECT FUEL PRESSURE SENSOR SIGNAL
CIRCUIT FOR SHORT TO GND
•Turn engine switch to OFF.
•Inspect continuity between fuel pressure
sensor terminal C and body GND.
•Is there continuity?Yes Repair or replace harness for short to GND, go to Step 9.
No Go to next step.
4INSPECT FUEL PRESSURE SENSOR POWER
CIRCUIT FOR OPEN
•Turn engine switch to ON. (Engine OFF)
•Inspect voltage at fuel pressure sensor
terminal C (harness side).
•Is voltage below 1.0 V?Yes Repair or replace harness for open, go to Step 9.
No Go to next step.
2
8
7
2
8
6
8
5
43
6
2
CBAC
B
A90
61
91PCM FUEL PRESSURE SENSOR
91 9061 FUEL PRESSURE SENSOR
HARNESS SIDE CONNECTORPCM
HARNESS SIDE CONNECTOR

ON-BOARD DIAGNOSTIC
F2–127
F2
DTC P0193A6E407001082223
Diagnostic procedure
DTC P0193 Fuel pressure sensor circuit high input
DETECTION
CONDITION•PCM monitors input voltage from fuel pressure sensor while engine is running. If input voltage from fuel
pressure sensor is above 4.8 V, PCM determines fuel pressure sensor circuit high input.
POSSIBLE
CAUSE•Fuel pressure sensor malfunction
•Connector or terminal malfunction
•Fuel pressure sensor power and signal circuits short each other
•Open circuit in wiring between fuel pressure sensor terminal B and PCM terminal 61
•Open circuit in wiring between fuel pressure sensor terminal A and PCM terminal 91
•PCM malfunction
STEP INSPECTION ACTION
1VERIFY RELATED REPAIR INFORMATION
AVAILABILITY
•Check for related Service Information
availability.
•Is any related repair information available?Yes Perform repair or diagnosis according to available Service
Information.
•If vehicle is not repaired, go to next step.
No Go to next step.
2INSPECT POOR CONNECTION OF FUEL
PRESSURE SENSOR CONNECTOR
•Turn engine switch to OFF.
•Inspect for poor connection (damaged, pulled-
out terminals, corrosion, etc.).
•Is there any malfunction?Yes Repair or replace suspected terminal, go to Step 7.
No Go to next step.
3INSPECT FUEL PRESSURE SENSOR CIRCUIT
FOR SHORT WITH EACH OTHER
•Turn engine switch to OFF.
•Inspect continuity between fuel pressure
sensor terminals C and B
•Is there continuity?Yes Repair or replace harness for short with each other, go to
Step 7.
No Go to next step.
4INSPECT FUEL TEMPERATURE SENSOR
•Inspect fuel temperature sensor.
(See F2–77 FUEL TEMPERATURE SENSOR
INSPECTION)
•Is there any malfunction?Yes Repair supply pump, go to Step 7.
(See F2–54 SUPPLY PUMP INSPECTION)
No Go to next step.
53
6
2
5
4
3
6
2
25
FUEL PRESSURE SENSOR
C
B
A90
61
91PCM
CBA
919061 FUEL PRESSURE SENSOR
HARNESS SIDE CONNECTORPCM
HARNESS SIDE CONNECTOR

ON-BOARD DIAGNOSTIC
F2–129
F2
DTC P0200A6E407001082224
Diagnostic procedure
DTC P0200 Fuel injector circuit malfunction
DETECTION
CONDITION•PCM monitors injection confirmation signal from IDM while engine is running. If injection confirmation
signal is not input normally, PCM determines fuel injector circuit malfunction.
POSSIBLE
CAUSE•IDM
•Connector or terminal malfunction
•Short to GND in wiring between IDM terminal 2B and PCM terminal 30
•Short to GND in wiring between IDM terminal 2C and PCM terminal 42
•Short to GND in wiring between IDM terminal 2D and PCM terminal 44
•Short to GND in wiring between IDM terminal 2E and PCM terminal 45
•Short to GND in wiring between IDM terminal 2F and PCM terminal 43
•Short to power circuit in wiring between IDM terminal 2B and PCM terminal 30
•Short to power circuit in wiring between IDM terminal 2C and PCM terminal 42
•Short to power circuit in wiring between IDM terminal 2D and PCM terminal 44
•Short to power circuit in wiring between IDM terminal 2E and PCM terminal 45
•Short to power circuit in wiring between IDM terminal 2F and PCM terminal 43
•Open circuit in wiring between IDM terminal 2B and PCM terminal 30
•Open circuit in wiring between IDM terminal 2C and PCM terminal 42
•Open circuit in wiring between IDM terminal 2D and PCM terminal 44
•Open circuit in wiring between IDM terminal 2E and PCM terminal 45
•Open circuit in wiring between IDM terminal 2F and PCM terminal 43
•PCM malfunction
STEP INSPECTION ACTION
1VERIFY RELATED REPAIR INFORMATION
AVAILABILITY
•Check for related Service Information
availability.
•Is any related repair information available?Yes Perform repair or diagnosis according to available Service
Information.
•If vehicle is not repaired, go to next step.
No Go to next step.
2FOLLOW OTHER DETECTED DTC FIRST
•Turn engine switch to OFF.
•Start engine.
•Has P0300 been detected?Yes Go to DTC P0300 inspection.
(See F2–136 DTC P0300)
No Go to next step.
743
6
2
7
5
43
6
2
2
2
2
3
3
3
4
4
4
7
7
7
7
6
6
6
2B
2C
2D
2E
2F30
42
44
45
43 IDM
PCM
2H2G 2F
2E
2D2C2B2A
45 44
434230 IDM
HARNESS SIDE CONNECTORPCM
HARNESS SIDE CONNECTOR

F2–132
ON-BOARD DIAGNOSTIC
DTC P0222A6E407001082226
Diagnostic procedure
DTC P0222 Accelerator position sensor No.2 circuit low input
DETECTION
CONDITION•PCM monitors input voltage from accelerator position sensor No.2 while engine is running. If input voltage
from accelerator position sensor No.2 is below 0.3 V, PCM determines accelerator position sensor No.2
circuit low input.
POSSIBLE
CAUSE•Accelerator position sensor No.2 malfunction
•Connector or terminal malfunction
•Open circuit in wiring between accelerator position sensor terminal A and PCM terminal 90
•Short to GND in wiring between accelerator position sensor terminal C and PCM terminal 88
•Accelerator position sensor No.2 signal and GND circuits short each other
•PCM malfunction
STEP INSPECTION ACTION
1PERFORM DTC CONFIRMATION PROCEDURE
•Perform “DTC Confirmation Procedure”.
(See F2–85 DTC CONFIRMATION
PROCEDURE)
•Is same DTC present during KOEO or KOER
self-test?Yes Go to next step.
No Intermittent concern exists. Go to “Intermittent Concern
Troubleshooting”.
(See F2–227 INTERMITTENT CONCERN
TROUBLESHOOTING)
ACCELERATOR POSITION SENSOR NO.2
72
7
5
6
27
54
3
2
A
C
D90
88
91PCM
DC B
A
91
9010 PCM
HARNESS SIDE CONNECTOR ACCELERATOR POSITION SENSOR
HARNESS SIDE CONNECTOR