length MAZDA 626 1987 Repair Manual

TECHNICAL DATA 30
Item Engine model RF-CX RF-N
Connecting rod and connecting rod bearing

Length (Center
to
center) mm (in) 151.95-152.05 (5.9823—5.9862)
Maximum twisting and bending mm (in) 0.080 (0.0031)
per 50
(1.969)
Small end bushing inner diameter mm (in) 30.014-30.030 (1.1817-1.1823) 25.014-25.030 (0.9848-0.9854)
Big end bore mm (in) 54.002-54.017 (2.1261-2.1266)
Big end width mm (in) 25.900—26.100 (1.0197—1.0276)
Connecting rod side clearance mm (in) Standard 0.11-0.262 (0.0043-0.0103) Connecting rod side clearance mm (in) Maximum 0.30 (0.012)

Crankshaft

Crankshaft runout mm (in) 0.05 (0.002) max.
Standard Standard 59.937-59.955 (2.3597-2.3604)
size Minimum 59.89 (2.358)
0.25 (0.010) Standard 59.687-59.705 (2.3499-2.3506)
Main journal diameter undersize Minimum 59.64 (2.348) mm (in) 0.50 (0.020) Standard 59.437-59.455 (2.3400-2.3407)
undersize Minimum 59.39 (2.338)
0.75 (0.030) Standard 59.187-59.205 (2.3302-2.3309)
undersize Minimum 59.14 (2.328)
Main journal taper and out-of-round mm (in) 0.05 (0.002) max.
Standard Standard 50.940-50.955 (2.0055—2.0061)
size Minimum 50.89 (2.004)
0.25 (0.010) Standard 50.690-50.705 (1.9957-1.9963)
Crankpin diameter undersize Minimum 50.64 (1.994) mm (in) 0.50 (0.020) Standard 50.440-50.455 (1.9858—1.9864)
undersize Minimum 50.39 (1.984)
0.75 (0.030) Standard 50.190-50.205 (1.9760-1.9766)
undersize Minimum 50.14 (1.974)
Crankpin taper and out-of-round mm (in) 0.05 (0.002) max.

Main bearing

Main journal bearing
oil
clearance Standard 0.031-0.050 (0.0012-0.0020)
mm (in) Maximum 0.08 (0.0031)
Available undersize bearina mm fin) 0.25 (0.010), 0.50 (0.020), 0.75 (0.030)

Crankpin bearing

Crankpin bearing
oil
clearance mm (in) Standard 0.027-0.055 (0.0011-0.0022) Crankpin bearing
oil
clearance mm (in) Maximum 0.08 (0.0031)
Available undersize bearing mm (in) 0.25 (0.010), 0.50 (0.020), 0.75 (0.030)

Thrust bearina (center main bearina)

Crankshaft end play mm (in) Standard 0.04-0.282 (0.0016—0.0111) Crankshaft end play mm (in) Maximum 0.30 (0.012)
Bearing width mm (in) Standard size 2.00-2.05 (0.0787-0.0807) Bearing width mm (in) Oversize 2.175-2.225 (0.0856-0.0876)

Timing belt

Deflection mm (in)/N (ka,
lb)
9.0-11.5 (0.35--0.45V98 (10,
22)
Drive belt deflection

Alternator mm (in) New 8-10 (0.31-0.39) Alternator mm (in) Used 9-11 (0.35-0.43)
A/C compressor mm (in) New 8.5-9.5 (0.33-0.37) A/C compressor mm (in) Used 9.5-10.5 (0.37-0.41)
Vacuum pump mm (in) New 7.5-8.5 (0.30—0.33) Vacuum pump mm (in) Used 8.5-9.5 (0.33-0.37)
P/S pump with vacuum pump mm (in) New 6.5-7.5 (0.26—0.30) P/S pump with vacuum pump mm (in) Used 7.0-8.0 (0.28—0.31)
Pressure wave supercharger
mm
(in) New 4.0-5.0 (0.16-0.20) Pressure wave supercharger
mm
(in) Used 4.5-5.5 (0.18-0.22)

30—13

TECHNICAL DATA 30
5. ENGINE ELECTRICAL SYSTEM
Gasoline Engine
——— Engine
F6 F8 FE FE FE
Item ____ F6 F8 (8 VALVE) (12 VALVE) (DOHC)

Battery
Voltage
Type and capacity
12, Negative ground
(20 hour rate) 34B19L(S) (33 Ah): General 50D20L (50 Ah), 55D23L (60 Ah):
ECE

Alternator
Type A.C.
Output V-A 12-70
Regulator type Transistorized (built-in
IC
regulator)
Regulated voltage 14.1-14.7
Brush length
mm (in) Standard 16.5 (0.650)
Minimum 8.0 (0.315)
Drive belt tension
mm (in)/98
N (10
kg,
22 lb)
New:
6-8
(0.24-0.32), Used:
7-9
(0.28—0.35)
Starter
Type Coaxial reduction: Middle East
&
General (FE
•
carburetor)
Non-reduction: Others
Output V-kW 12-0.85
Brush length mm (in)
12-0.95
Standard 17.0 (0.669)
Minimum 11.5 (0.453)

Unleaded fuel

17,0 (0.669)

Others

17.5 (0.689)

Unleaded fuel
11.5 (0.453)
Others
10.0 (0.394)

12-1.4 12-0.95
17.0 (0.669)
11.5 (0.453)
Ignition timing 6
±
1
°
BTDC (Vacuum hose disconnected) 12
±
1° BTDC
(Test connector
grounded)
Distributor
Type Fully transistorized (HEI)
Electronic spark advance
Centrifugal spark advance
(crank angle/engine speed)
degree/rpm
F6
-2-2/1,000 6-10/2,100 14-18/6,100
F8 -2-2/1,000 10—14/2,100 18-22/6,100
FE
(8
VALVE)—Carburetor Unleaded fuel
(MTX)-2—2/1,760 12—16/3,360 22—26/5,320 (ATX)-2-2/1,300 12-16/3,360 22-26/5,320
Others
-2-2/1,460 10-14/2,540 22-26/5,540
FE (12 VALVE)—Carburetor -2-2/1,200 10-14/2,400 10-14/4,000 16-20/5,000
FE—Fuel injection (except
FE
DOHC)
-2-2/1,000 10-14/2,600 10-14/4,600 16-20/5,800

30—23

30 TECHNICAL DATA
Engine
Item F6 F8 FE FE FE F8 (8 VALVE) (12 VALVE) (DOHC)

Distributor
Vacuum spark advance
(Crank angle/Vacuum)
degree/mmHg (inHg)
Type
Spark plug
F6 and
F8
-2-2/100
6-10/300
FE
(8
VALVE)—Carburetor Unleade fuel -2-2/120 8-12/245
Others (MTX)-2-2/100 16-20/250
(ATX) -2-2/100 10-14/200
FE (12 VALVE)—Carburetor
-2-2/120 11-15/300
FE—Fuel injection (except
FE
DOHC) [A chamber] -2-2/125 18—22/300
[B chamber] -2-2/125
-6--10/200

FE
(8
VALVE)* NGK: BPR5ES-11, BPR6ES-11 Nippon Denso: W16EXR-U11, W20EXR-U11
Others NGK: BPR5ES, BPR6ES Nippon Denso: W16EXR-U, W20EXR-U
Plug
gap
mm (in)

Firing order

0.75-0.85 (0.030-0.033),
FE

(8 VALVE)* 1.0-1.1
(0.039-0.043)

1-3-4-2

NGK:
BCPR5E, BCPR6E Nippon Denso: Q16PR-U, Q20PR-U
0.7-0.8
(0.028-0.031)

NGK:

Unleaded fuel BCPR5E-11 BCPR6E-11 BCPR7E-11
Leaded fuel BCPR5E BCPR6E

1.0-1.1 (0.039-0.043)*1
0.7-0.8
(0.028-0 031)'2
Diesel Engine
————Engine Item " RF-N RF-CX

r5a!:ery
Voltaae
V
12, Negative around
r5a!:ery Type and capacity (20 hour rate) 80D26L (65)
50D20L, 50D20R (50)-ECE 80D26L (65) 65D23L, 65D23R (55)
Alternator

TvDe
A.C.
Alternator
Output
V—A
12-70 12-75
Alternator
Regulator tvoe Transistorized (built-in
IC
reaulator)
Alternator Regulated voltaae
V
14.1-14.7 Alternator
Brush length mm (in)
Standard 16.5 (0.650) 21.5 (0.846)
Alternator
Brush length mm (in) Minimum 8.0 (0.315) 8.0 (0.315)
Alternator
Drive belt tension
mm (in)/98
N
(10 ka,
92 lb)
New: 9-11 (0.35-0.43), Used: 12-14 (0.47-0.55)
Starter
Type Reduction
Starter Output V—kW 12-2.0, 12-2.2 (Cold area) Starter Brush length
mm (in)
Standard 2.0 kW: 17.0 (0.669),
2.2
kW: 18.0 (0.709) Starter Brush length
mm (in) Minimum 2.0 kW: 11.0 (0.453).
2.2
kW: 11.0 (0.453)
Firina order 1-3-4-2
*1 Unleaded fuel model
*2 Leaded fuel model

30-24

30 TECHNICAL DATA
Model G4A-EL G4A-HL (4-speed)
Item (EC-AT) FE engine F8 engine
Forward clutch

Number
of
drive/driven plate 3/3
Drive plate thickness mm (in) Standard 1.6 (0.063) Drive plate thickness mm (in) Minimum 1.4 (0.055)
Forward clutch clearance mm (in) 1.0—1.2 (0.040—0.047)
Retaining plate sizes mm (in) 5.9 (0.232), 6.1 (0.240), 6.3 (0.248),
6.5 (0.256), 6.7 (0.264),
8.9
(0.350)

Coasting clutch

Number
of
drive/driven plates 2/2
Drive plate thickness mm (in) Standard 1.6 (0.063) Drive plate thickness mm (in) Minimum 1.4 (0.055)
Coasting clutch clearance mm (in) 1.0-1.2 (0.040—0.047)
Retaining plate sizes mm (in) 4.6 (0.181), 4.8 (0.189), 5.0 (0.197),
5.2 (0.205), 5.4 (0.213), 5.6 (0.220)
Return spring free length mm (in) 29.8 (1.173)

Reverse clutch

Number
of
drive/driven plates 2/2
Driven plate thickness mm (in) Standard 1.6 (0.063) Driven plate thickness mm (in) Minimum 1.4 (0.055)
Reverse clutch clearance mm (in) 2.1—2.4 (0.083—0.094)
Retaining plate sizes mm (in) 6.6 (0.260),
6.8
(0.268), 7.0 (0.276), 7.2 (0.283), 7.4 (0.291), 7.6 (0.299)

3-4 clutch

Number
of
drive/driven plates 5/5 4/4
Drive plate thickness mm (in) Standard 1.6 (0.063) Drive plate thickness mm (in) Minimum 1.4 (0.055)
3-4 clutch clearance mm (in) 1.3-1.5 (0.051-0.059)
Retaining plate sizes mm (in) 3.8 (0.150), 4.0 (0.157), 4.2 (0.165), 4.4 (0.173), 4.6 (0.181), 4.8 (0.189)
4.8 (0.819), 5.0 (0.197), 5.2 (0.205), 5.4 (0.213), 5.6 (0.220)
Return spring free length mm fin) 33.2 (1.307)

Low and reverse brake

Number
of
drive/driven Dlates 3/3 4/4
Drive plate thickness mm (in) Standard 1.6 (0.063) Drive plate thickness mm (in) Minimum 1.4 (0.055)
Low and reverse brake clearance mm (in) 2.1-2.4 (0.083-0.094)
Retaining plate sizes mm (in) 6.8 (0,268), 7.0 (0.276), 7.2 (0.283), 7.4 (0.291), 7.6 (0.299), 7.8 (0.307)
10.0 (0.394), 10.2 (0.402), 10.4 (0.410),
10.6 (0.417), 10.8 (0.425)
Return spring free length mm (in) 20.5 (0.807)
Sun gear drum bushing mm (in) Maximum 33.425 (1.316)
Small sun gear bushing mm (in) Maximum 24.021 (0.946)

Carrier hub

Clearance between pinion washer and planet carrier
mm (in)
Maximum 0.2-0.7 (0.008-0.028)

Servo

Free length
of
return spring mm (in) Standard 43.25 (1.703) 42.0 (1.654) 43.25 (1.703)

2-3 accumulator valve

2-3 accumulator valve spring mm (in) Standard 83.3
mm
(3.280) 76.0 (2.992)

30—30

TECHNICAL DATA 30
Control valve spring (G4A-EL)
Spring name Outer dia. mm (in) Free length mm (in) Wire dia. mm (in) Spring color

1-2 accumulator small spring 11.0 (0.433) 88.1 (3.348) 1.4 (0.055) Gray
1-2 accumulator large spring 16.0 (0.0630) 78.0 (3.071) 2.0 (0.079) Blue
Bypass, servo control spring 5.0 (0.197) 33.4 (1.315) 0.55 (0.022) Maroon
2-3 timing spring 8.3 (0.327) 26.5 (1.043) 0.8 (0.031)
—

N-R accumulator rear spring 11.1 (0.437) 62.0 (2.441) 1.2 (0.047) Light green
N-D accumulator front spring 9.8 (0.386) 52.9 (2.083) 1.0 (0.039) Brown
Coasting bypass spring 5.8 (0.228) 37.7 (1.484) 0.6 (0.024) Dark blue
3-2 timing spring 8.2 (0.323) 28.6 (0.126) 0.8 (0.031) Red
3-2 capacity spring 5.4 (0.213) 30.6 (1.205) 0.5 (0.020) White
Throttle relief ball spring 6.6 (0.260) 21.6 (0.850) 0.8 (0.031)
—

Pressure modifier spring 8.3 (0.327) 26.5 (1.043) 0.8 (0.031)
—

Low reducing spring 8.7 (0.343) 38.3 (1.508) 0.9 (0.035) Black
1-2 shift spring 8.7 (0.343) 41.3 (1.626) 1.0 (0.039) Yellow
2-3, 3-4 shift spring 7.4 (0.291) 36.6 (1.441) 0.8 (0.031) Gray
Throttle backup spring 9.65 (0.380) 26.9 (1.059) 0.55 (0.022) Red
Throttle modulator spring 6.3 (0.248) 47.9 (1.886) 0.8 (0.031)
—

Throttle assist spring 5.15 (0.203) 32.3 (1.272) 0.55 (0.022) Dark green
Throttle spring 5.4 (0.213) 47.2 (1.858) 0.8 (0.031) Pink
Converter relief ball spring 6.9 (0.272) 24.1 (0.949) 0.9 (0.035) Maroon
Orifice check valve spring 5.0 (0.197) 12.5 (0.492) 0.23 (0.009)
—

Pressure regulator spring 11.5 (0.453) 26.5 (1.043) 1.0 (0.039) Maroon
Lock-up control spring 5.0 (0.197) 35.2 (1.386) 0.6 (0.024) Purple

Control valve springs (G4A-HL)
SDrina name Outer dia. mm (in) Free length mm (in) Wire dia. mm (in) Spring color

1-2 accumulator small spring F8 enaine 9.9 (0.400) 84.7 (3.335) 1.2 (0.047) Red
1-2 accumulator large spring FE engine 13.0 (0.512) 73.2 (2.881) 1.8 (0 071) Pink 1-2 accumulator large spring F8 enaine 16.0 (0.630) 84.7 (3.335) 2.0 (0.079) White
Bypass spring 5.0 (0.197) 25.1 (0.988) 0.7 (0.028) Yellow
Servo control sorina 4.9 (0.193) 27.1 (1.067) 0.5 (0.020) Light blue
2-3 timing soring 8.3 (0.327) 26.5 (1.043) 0.8 (0.031)
—

N-R
accumulator rear SDrina
11.1 (0.437) 68.2 (2.685) 1.0 (0.039) Blue
N-D accumulator front spring 9.8 (0.386) 60.9 (2.398) 1.1 (0.043) Yellow
Low reducing spring 8.7 (0.343) 38.3 (1.508) 0.9 (0.035) Black
OD release spring 6.0 (0.236) 32.6 (1.283) 0.6 (0.024) Orange
Coasting bypass spring 5.8 (0.228) 31.3 (1.232) 0.6 (0.024) Yellow
3-2 timing soring 8.2 (0.323) 28.55 (1.124) 0.8 (0.031) Maroon
3-2 capacity spring 5.55 (0.219) 30.5 (1.201) 0.55 (0.022) Light green
Throttle relief ball soring 6.6 (0.260) 20.3 (0.799) 0.8 (0.031) Light green
1-2 shift control spring 5.5 (0.217) 46.0 (1.811) 0.5 (0.020) Liaht oreen
1-2 shift soring 5.0 (0.197) 24.9 (0.980) 0.5 (0.020) Gray
2-3 shift soring 6.1 (0.240) 39.7 (1.563) 0.65 (0.026) Pink
3-4 shift spring 6.4 (0.252) 37.0 (1.457) 0.6 (0.024)
—

Throttle backup spring 6.4 (0.252) 33.5 (1.319) 0.6 (0.024) Pink
Throttle modulator front spring 5.0 (0.197) 27.8 (1.094) 0.6 (0.024) Red
Throttle modulator rear spring 7.15 (0.281) 30.8 (1.213) 0.85 (0.033) Red
1
ranoe control SDrina
6.15 (0.242) 39.2 (1.543) 0.65 (0.026) White
2 range control spring 3.95 (0.156) 32.1 (1.264) 0.45 (0.018)
—

Kick-down
SDrina
5.4 (0.213) 38.1 (1.500) 0.8 0.031)
—

Throttle assist spring 5.15 (0.203) 32.3 (1.272) 0.55 (0.022) Dark green
Throttle spring 5.4 (0.213) 48.3 (1.902) 0.8 (0.031)
—

Converter relief ball spring 6.9 (0.272) 24.1 (0.949) 0I9 (0.035) Maroon
Orifice check valve soring 5.0 (0.197) 12.5 (0.492) 0.23 (0.009)
—
30—31

30 TECHNICAL DATA
Spring name Outer dia. mm (in) Free length mm (in) Wire dia. mm (in)
I
Spring color

Pressure regulator spring 9.5 (0.374) 30.7 (1.209) 0.7 (0.028)
—

Lock-up control spring 7.3 (0.287) 46.2 (1.819) 0.8 (0.031) Blue
Lock-up support spring 6.1 (0.240) 43.5 (1.713) 0.65 (0.026) Blue
OD lock-up spring 7.1 (0.280) 66.5 (2.618) 0.8 (0.031) Red

Model G4A-EL G4A-HL 4-speed)
Item (EC-AT) FE engine F8 engine
Gear assembly

Total end play mm (in) 0.25-0.50 (0.010-0.020)
End play adjust race mm (in) 1.2 (0.047),
1.4
(0.055),
1.6
(0.063),
1.8 (0.071), 2.0 (0.079),
2.2
(0.087)
Idle gear bearing preload N
m
(cm-kg, in-lb) 0.03--0.9 (0.3—9.0, 0.26 -7.8)
Preload adjust shims mm (in) 0.10 (0.004), 0.12 (0.005), 0.14 (0.006), 0.16 (0.0063), 0.18 (0.007), 0.20 (0.008)
Output gear bearing preload N-m (cm-kg, in-lb) 0.03--0.9 (0.3—9.0, 0.26 -7.8)
Preload adjust shims mm (in) 0.10 (0.004), 0.12 (0.005), 0.14 (0.006), 0.16 (0.0063),
0.18 (0.007), 0.20 (0.008), 0.50 (0.020)

Drive and differential

Final gear Type Helical gear Final gear Reduction ratio 3,700
: 1

Side bearing preload N-m (cm-kg, in-lb) 2.9 —3.9 (30-40,
26-
35)
Preload adjust shims mm (in)
0.10 (0.004), 0.12 (0.005), 0.14 (0.006), 0.16 (0.0063), 0.18 (0.007), 0.20 (0.008), 0.50 (0.020), 0.70 (0.028), 1.00 (0.039)
Backlash
of
side gear and pinion
mm (in)
Standard 0.025-0.1 (0.001-0.004) Backlash
of
side gear and pinion
mm (in)
Maximum 0.5 (0.020)
Torque converter distance "A" (Refer to page 7B— 214) mm (in) 25 (0.984)

30-32

30 TECHNICAL DATA
Item Engine model FE engine F6 engine
Front clutch

Number
of
driven and drive plates 3
Drive plate thickness mm (in) Standard 1.6 (0.063) Drive plate thickness mm (in) Minimum 1.4 (0.055)
Front clutch clearance mm (in) 1.6-1.8 (0.063-0.071)
Retaining plate sizes mm (in) 5.2 (0.205), 5.4 (0.213), 5.6 (0.220),
5.8 (0.228), 6.0 (0.236), 6.2 (0.244)
Return spring free length mm (in) 26.2 (1.031)
Drum bushing inner diameter mm (in) Standard 44.000-44.025 (1.732-1.733) Drum bushing inner diameter mm (in) Maximum 44.075 (1.735)
Front clutch drum end play mm (in) 0.5-0.8 (0.197-0.0315)
End play adjust shims mm (in) 1.3 (0.0512), 1.5 (0.0591), 1.7 (0.0669), 1.9 (0.0748), 2.1 (0.0827), 2.3 (0.0906),
2.5
(0.0984), 2.7 (0.1063)

Rear clutch

Number
of
driven and drive plates 4
Drive plate thickness mm (in) Standard 1.6 (0.063) Drive plate thickness mm (in) Minimum 1.4 (0.055)
Rear clutch clearance mm (in) 0.8--1.0 (0.0315- 0.0394)
Retaining plate sizes mm (in) 4.8 (0.189), 5.0 (0.197), 5.2 (0.205), 5.4 (0.213),
5.6 (0.220), 5.8 (0.228), 6.0 (0.236), 6.2 (0.244)
Return spring free length mm (in) 26.2 (1.031)

Low and reverse brake

Number
of
low and reverse brake plates 4
Drive plate thickness mm (in) Standard 1.6 (0.063) Drive plate thickness mm (in) Minimum 1.4 (0.055)
Low and reverse brake clearance mm (in) 0.8-1.05 (0.032-0.041)
Retaining plate sizes mm (in) 4.6 (0.181),
4.8
(0.189), 5.0 (0.197), 5.2 (0.205), 5.4 (0.213), 5.6 (0.220)
Return spring free length mm (in) 27.7 (1.091)

Servo

Return sprina free lenath mm (in) 48.0 (1.89) 45.5 (1.79)

Governor

Primary spring mm (in) Outer diameter 9.0 (0.354) Primary spring mm (in) Free lenath 17.2 (0.667)
Secondary spring mm (in) Outer diameter 9.25 (0.364) Secondary spring mm (in) Free lenath 13.2 (0.520)

One-wav clutch

Bushing diameter mm (in) Standard 129.987-130.013 (5.118--5.119) Bushing diameter mm (in) Maximum 130.063 (5.121)

Control valve SDrinas
Spring name Outer dia. mm (in) Free length mm (in) Wire dia. mm (in)

Throttle backup spring 7.3 (0.287) 36.0 (1.417) 0.8 (0.031)
Downshift sorina 5.55 (0.219) 21.9 (0.862) 0.55 (0.022)
2-3 shift spring 6.9 (0.272) 41.0 (1.614) 0.7 (0.028)
1-2 shift spring 6.4 (0.252) 31.63 (1.245) 0.4 (0.016)
Second lock spring 5.55 (0.219) 33.5 (1.319) 0.55 (0.022)
Pressure reaulator sprina 11.7 (0.461) 43.0 (1.693) 1.2 (0.047)
Throttle relief ball spring 7.0 (0.276) 11.2 (0.441) 0.9 (0.035)
Orifice check valve sprina 5.0 (0.197) 15.5 (0.610) 0.23 (0.009)

30-34

30 TECHNICAL DATA
9. FRONT AND REAR AXLES
Transaxle type MTX ATX
Item Non-Turbo Turbo Non-Turbo Turbo
Driveshaft

Joint type Inside Ball joint Tripod joint Joint type Outside Ball joint Ball joint
Shaft length mm (in) Right 360.0 (14.17) 355.5 (14.00) 355.5 (14.00) 348.8 (13.73) Shaft length mm (in) Left 360.0 (14.17) 355.5 (14.00) 355.5 (14.00) 348.8 (13.73)
Shaft diameter mm (in) 24 (0.94) 26 (1.02) 24 (0.94) 26 (1.02)

Front axle

Front wheel bearing end play mm (in) 0.2 (0.0079) max.

Rear axle

Rear wheel bearing end play mm (in) 0.2 (0.0079) max.

10. STEERING SYSTEM
u _ Type Item ——- - -. Manual steering Power steering

Steering wheel Outer diameter mm (in) 380 15.0) Steering wheel Turns lock
to
lock 4.32 2.93
Steering shaft and joints
Shaft type Collapsible
Steering shaft and joints Joint type Cross joints
(2)
Steering shaft and joints
Tilt stroke mm (in) 40 (1.6)
Front steering gear Type Rack and pinion Front steering gear Gear ratio
oo
(infinite)
Power steering fluid
Capacity liter
(US quarts, Imp quarts)
2WS
—
0.9 (0.95, 0.79)
Power steering fluid
Capacity liter
(US quarts, Imp quarts) 4WS
—
1.0 (1.06, 0.88) Power steering fluid
Type 2WS 4WS
—
Dexron
II or M III
30—36

TECHNICAL DATA 30
11. BRAKING SYSTEM
Item Specifications

Brake
pedal
Height
mm
(in) LHD
&
RHD 222 (8.74 _+g2)
Brake
pedal
Free play
mm
(in) 4-7 (0.16—0.28)
Brake
pedal
Reserve travel
mm (in)

(Clearance when pedal
is
depressed
at 5S

95 (3.74) min.
39
N
(60 kg, 132 lb))
Brake
pedal
Lever ratio 4.2
Brake
pedal
Max. stroke
mm (in)
LHD: 136.5 (5.37) RHD: 135 (5.31)
Master cylinder
Type Tandem Master cylinder Bore
mm
(in) 22.22 (0.875) Master cylinder Fluid type DOT-3
or 4, or
SAE J1703
Front disc brake
Type Disc (ventilated)
Front disc brake
Thickness
of
pad
mm (in)
Standard 10.0 (0.39)
Front disc brake
Thickness
of
pad
mm (in)
Minimum 2.0 (0.08)
Front disc brake
Area
of
pad mm2 (in2) 4,800 (7.44) Front disc brake Outer diameter
of
disc plate
mm (in)
14
or 15
inch-wheel: 264 (10.39)
13
inch-wheel: 242 (9.53) Front disc brake Thickness
of
disc plate
mm (in)
Standard 14
or 15
inch-wheel: 24.0 (0.94)
13
inch-wheel: 20.0 (0.79)
Front disc brake Thickness
of
disc plate
mm (in) Minimum 14
or 15
inch-wheel: 22.0 (0.87)
13
inch-wheel: 18.0 (0.71)
Front disc brake
Disc plate runout
mm (in)
Maximum 0.1 (0.004)
Front disc brake
Wheel cylinder bore
mm (in)
53.97 (2.125)
Rear drum
brake
Type Leading-trailing
Rear drum
brake
Clearance between shoe and drum Self-adjusting
Rear drum
brake
Thickness
of
lining mm (in)
Standard (a):
4.5
(0.18) (b): 5.0 (0.20)
Rear drum
brake
Thickness
of
lining mm (in) Minimum 1.0 (0.04) Rear drum
brake Width
of
lining
mm (in)
(a):
30
(1.18)
(b)
25 (0.98) Rear drum
brake Length
of
lining
mm fin)
(a): 219.3 (8.63)
(b)
1919 (7.56)
Rear drum
brake
Inner diameter
of
drum mm (in)
Standard (a): 228.6 (9.00)
(b)
200 (7.87)
Rear drum
brake
Inner diameter
of
drum mm (in) Maximum (a): 230.1 (9.06)
(b)
201.5 (7.93)
Rear drum
brake
Wheel cylinder bore
mm (in)
17.46 (0.687)
Rear disc
brake
TvDe Disc (solid)
Rear disc
brake
Thickness
of
pad
mm (in)
Standard 8.0 (0.31)
Rear disc
brake
Thickness
of
pad
mm (in)
Minimum 1.0 (0.04)
Rear disc
brake
Area
of
pad mm2 (in2) 2,900 (4.5) Rear disc
brake Outer diameter
of
disc plate
mm (in)
259 (10.2) Rear disc
brake Thickness
of
disc plate mm (in)
Standard 10.0 (0.40)
Rear disc
brake Thickness
of
disc plate mm (in) Minimum 8.0 (0.31)
Rear disc
brake
Disc
Dlate runout mm fin)
Maximum 0.1 (0.04)
Rear disc
brake
Wheel cylinder bore
mm (in)
30.2 (1.19)
Parking
brake
TvDe Center lever Parking
brake Lever notches
(Pulled
at
98N
(10
kg,
22 lb))
5-7
Power
brake unit
Diameter
mm (in)
238 (9.37)
Power
brake unit
Clearance between master cylinder piston and push
rod mm
(in) 0(0)
Power
brake unit Fluid pressure per treading force
kPa (kg/cm
,
psi)/N (kg,
lb)

1,177 (12,171 )/196 (20,
44)
min. when
no
vacuum
is
applied 7,063 (72, 1,024)/196 (20,
44)
min.
when 500 mmHg (19.7
in
Hg) vacuum
is
applied
Rear wheel hydraulic control devise (svstem)
Type Dual proportioning valve (Non-ABS)
or
ABS Rear wheel hydraulic control devise (svstem) Switching point kPa (kg/cm2,
psi)
Except General LHD and RHD: 1,962 (20, 284) General LHD and RHD: 2,942 (30, 427)
(a): Except
13
inch-wheels
in
General LHD and RHD vehicles (b):
13
inch-wheels
in
General LHD and RHD vehicles

30—37

30 TECHNICAL DATA
12. WHEEL AND TIRE
* ~— - Type
Item ~ ———_____ Standard Temporary spare
(if equipped)

Wheel
Size
5-Jx13
4-T
x 15

Wheel
Size 5 1/2-JJx14 4-T
x 15

Wheel
Size
6JJx15
4-T
x 15

Wheel
Offset
mm (in)
42 (1.65) 53 (2.09)
Wheel Diameter
of
pitch circle
mm
(in) 114.3 (4.5) Wheel
Material Steel
or
aluminum alloy Steel
Wheel
Number
of

fixing nuts
13 inch-wheel 4
4
or 5

Wheel
Number
of

fixing nuts 14 inch-wheel 5 4
or 5

Wheel
Number
of

fixing nuts 15 inch-wheel 5 4
or 5

Tire
Size
13 inch-wheel
6.45-13-6PR 165SR13 165/80R13 82S
185/70HR13 185/70R13 85H
T125/70D15
Tire
Size
14 inch-wheel
185/70HR14 185/70R14 87H 185/70R14 88H 185/70VR14
T125/70D15
Tire
Size
15 inch-wheel 195/60R15 86H 195/60VR15
T125/70D15
Tire
Air pressure kPa (kg/cm2, psi)
Front 216 (2.2, 31)
or
196 (2.0, 28)
Refer to tire labels for applications 412 (4.2, 60)
Tire
Air pressure kPa (kg/cm2, psi) Rear 177 (1.8,
26)

412 (4.2, 60)
Wheel and tire
Runout
mm (in)
Horizontal Steel wheel: 2.5 (0.098), Alminum allov wheel: 2.0 (0.079) max.
Wheel and tire
Runout
mm (in) Vertical 2.0 (0.079) max.
Wheel and tire Unbalance

g
(oz)
13 inch-wheel 11 (0.39) max. Wheel and tire Unbalance

g
(oz) 14 inch-wheel 10 (0.35) max.
Wheel and tire Unbalance

g
(oz) 15 inch-wheel 9 (0.32) max.

13. SUSPENSION
Item Specification
Front suspension

Type Strut
Toe-in
mm
(in) 0 ±
3 (0
±
0
12)
Front wheel alignment Camber angle 0°17' ±
45'
Front wheel alignment Caster angle 1 °13' ±
45'

King pin angle 12C 47'
Maximum front Inner 36°26'33"
steering angle Outer 30°59'15"
Stabilizer Type Torsion
bar
Stabilizer Diameter
mm (in)
20.0 (0.79)
Shock absorbers Standard suspension Oil type Shock absorbers Auto adjust suspension Low-pressure gas sealed type
Identification color Orange Green Light green Pink Brown Purple Gray Blue
Wire diameter
mm (in)
12.5
(0.49)
12.6
(0.49) 12.8 (0.50) 12.9 (0.51) 13.1 (0.52) 13.3 (0.53) 13.6 (0.54) 13.7 (0.54)
Coil springs* Coil inner diameter mm (in) 147.5 (5.8)
Free length
mm
(in) 344 (13.5)

CO <35
362
(14.3)
370
(14.6)
372 (14.6) 365 (14.4) 350 (13.8) 358 (14.1)
Coil number 4.99 5.09 5.31 5.42 5.53 5.46 5.34 5.45
* Refer
to
pages 13—5,6,7
for
coil spring applications

30-38