warning light MAZDA MODEL 2 2019 (in English) Owner's Guide
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2019, Model line: MODEL 2, Model: MAZDA MODEL 2 2019Pages: 759, PDF Size: 13.38 MB
Page 354 of 759
NOTE
xUnder the following conditions, the
radar sensor (front) may not be able to
detect vehicles ahead or obstructions
correctly and each system may not
operate normally.
xThe rear surface of a vehicle ahead
does not reflect radio waves
effectively, such as an unloaded
trailer or an automobile with a
loading platform covered by a soft
top, vehicles with a hard plastic
tailgate, and round-shaped vehicles.
xVehicles ahead with low vehicle
height and thus less area for
reflecting radio waves.
xVisibility is reduced due to a vehicle
ahead casting off water, snow, or
sand from its tyres and onto your
windscreen.
xThe boot/luggage compartment is
loaded with heavy objects or the rear
passenger seats are occupied.
xIce, snow, or soiling is on the front
surface of the front emblem.
xDuring inclement weather such as
rain, snow, or sand storms.
xWhen driving near facilities or
objects emitting strong radio waves.
xUnder the following conditions, the
radar sensor (front) may not be able to
detect vehicles ahead or obstructions.
xThe beginning and end of a curve.
xRoads with continuous curves.
xNarrow lane roads due to road
construction or lane closures.
xThe vehicle ahead enters the radar
sensor's blind spot.
xThe vehicle ahead is running
abnormally due to accident or
vehicle damage.
xRoads with repeated up and down
slopes
xDriving on poor roads or unpaved
roads.
xThe distance between your vehicle
and the vehicle ahead is extremely
short.
xA vehicle suddenly comes close such
as by cutting into the lane.
xTo prevent incorrect operation of the
system, use tyres of the same specified
size, manufacturer, brand, and tread
pattern on all 4 wheels. In addition, do
not use tyres with significantly different
wear patterns or tyre pressures on the
same vehicle (Including the temporary
spare tyre).
xIf the battery power is weak, the system
may not operate correctly.
xIf the vehicle is driven on a road with
little traffic and few vehicles ahead or
obstructions for the radar sensor
(front) to detect, the sensor detects that
the radar sensor (front) is dirty and the
Smart Brake Support/Smart City Brake
Support (SBS/SCBS) Warning Light
(amber) may be temporarily turned on.
However, it does not indicate a
malfunction.
xThe radar sensors are regulated by the
relevant radio wave laws of the country
in which the vehicle is driven. If the
vehicle is driven abroad, authorization
from the country in which the vehicle is
driven may be required.
: K H Q ' U L Y L Q J
L $ & 7 , 9 6 ( 1 6 (
Page 366 of 759
Please note that the TPMS is not a substitute for proper tyre maintenance, and it is the
driver's responsibility to maintain correct tyre pressure, even if under-inflation has not
reached the level to trigger illumination of the TPMS low tyre pressure telltale.
Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when
the system is not operating properly.
The TPMS malfunction indicator is combined with the low tyre pressure telltale. When the
system detects a malfunction, the telltale will flash for approximately one minute and then
remain continuously illuminated. This sequence will continue upon subsequent vehicle
start-ups as long as the malfunction exists. When the malfunction indicator is illuminated,
the system may not be able to detect or signal low tyre pressure as intended. TPMS
malfunctions may occur for a variety of reasons, including the installation of replacement
or alternate tyres or wheels on the vehicle that prevent the TPMS from functioning properly.
Always check the TPMS malfunction telltale after replacing one or more tyres or wheels on
your vehicle to ensure that the replacement or alternate tyres and wheels allow the TPMS to
continue to function properly.
¾To avoid false readings, the system samples for a little while before indicating a problem. As
a result it will not instantaneously register a rapid tyre deflation or blow out.
NOTE
Because this system detects slight changes in tyre conditions, the timing of the warning may
be faster or slower in the following cases:
xThe size, manufacturer, or the type of tyres is different from the specification.
xThe size, manufacturer, or the type of a tyre is different from the others, or the level of tyre
wear is excessively different between them.
xA run-flat tyre, studless tyre, snow tyre, or tyre chains are used.
xAn emergency tyre is used (The tyre pressure monitoring system warning light may flash
and then continue illuminating).
xA tyre is repaired using the emergency flat tyre repair kit.
xThe tyre pressure is excessively higher than the specified pressure, or the tyre pressure is
suddenly lowered for some reason such as a tyre burst during driving.
xThe vehicle speed is lower than about 15 km/h (9.3 mph) (including when the vehicle is
stopped), or the drive period is shorter than 5 minutes.
xThe vehicle is driven on an extremely rough road or a slippery, icy road.
xHard steering and rapid acceleration/deceleration are repeated such as during aggressive
driving on a winding road.
xLoad on the vehicle is applied to a tyre such as by loading heavy luggage to one side of
the vehicle.
xSystem initialization has not been implemented with the specified tyre pressure.
: K H Q ' U L Y L Q J
7 \ U H 3 U H V V X U H 0 R Q L W R U L Q J 6 \ V W H P
Page 367 of 759
![MAZDA MODEL 2 2019 (in English) Owners Guide ▼ 7 \ U H 3 U H V V X U H 0 R Q L W R U L Q J 6 \ V W H P
, Q L W L D O L ] D W L R Q
, Q W K H I R O O R Z L Q J F D V H V V \ V W H P
L Q L W L D O L ] D W L R Q P X V W E H](/img/28/15645/w960_15645-366.png "MAZDA MODEL 2 2019 (in English) Owners Guide ▼ 7 \ U H 3 U H V V X U H 0 R Q L W R U L Q J 6 \ V W H P
, Q L W L D O L ] D W L R Q
, Q W K H I R O O R Z L Q J F D V H V V \ V W H P
L Q L W L D O L ] D W L R Q P X V W E H")
▼ 7 \ U H 3 U H V V X U H 0 R Q L W R U L Q J 6 \ V W H P
, Q L W L D O L ] D W L R Q
, Q W K H I R O O R Z L Q J F D V H V V \ V W H P
L Q L W L D O L ] D W L R Q P X V W E H S H U I R U P H G V R W K D W W K H
V \ V W H P R S H U D W H V Q R U P D O O \
x $ W \ U H S U H V V X U H L V D G M X V W H G
x 7 \ U H U R W D W L R Q L V S H U I R U P H G
x $ W \ U H R U Z K H H O L V U H S O D F H G
x 7 K H E D W W H U \ L V U H S O D F H G R U F R P S O H W H O \
G U D L Q H G
x 7 K H W \ U H S U H V V X U H P R Q L W R U L Q J V \ V W H P
Z D U Q L Q J O L J K W L V L O O X P L Q D W H G
, Q L W L D O L ] D W L R Q P H W K R G
3 D U N W K H F D U L Q D V D I H S O D F H D Q G I L U P O \
D S S O \ W K H S D U N L Q J E U D N H
/ H W W K H W \ U H V F R R O W K H Q D G M X V W W K H W \ U H
S U H V V X U H R I D O O I R X U W \ U H V W R W K H
V S H F L I L H G S U H V V X U H L Q G L F D W H G R Q W K H W \ U H
S U H V V X U H O D E H O O R F D W H G R Q W K H G U L Y H U
V
G R R U I U D P H G R R U R S H Q
5 H I H U W R 7 \ U H V R Q S D J H
6 Z L W F K W K H L J Q L W L R Q 2 1
3 U H V V D Q G K R O G W K H W \ U H S U H V V X U H
P R Q L W R U L Q J V \ V W H P V H W V Z L W F K D Q G
Y H U L I \ W K D W W K H W \ U H S U H V V X U H P R Q L W R U L Q J
V \ V W H P Z D U Q L Q J O L J K W L Q W K H L Q V W U X P H Q W
F O X V W H U I O D V K H V W Z L F H D Q G D E H H S V R X Q G
L V K H D U G R Q F H
& $ 8 7 , 2 1
If the system initialization is performed
without adjusting the tyre pressure, the
system cannot detect the normal tyre
pressure and it may not illuminate the tyre
pressure monitoring system warning light
even if a tyre pressure is low, or it may
illuminate the light even if the pressures are
normal.
Adjust the tyre pressure on all four tyres
and initialize the system when the warning
light is turned on. If the warning light turns
on for a reason other than a flat tyre, the
tyre pressure of all four tyres may have
decreased naturally.
The system initialization will not be
performed if the switch is pressed while the
vehicle is being driven.
: K H Q ' U L Y L Q J
7 \ U H 3 U H V V X U H 0 R Q L W R U L Q J 6 \ V W H P
Page 397 of 759
6 H W W K H I D Q F R Q W U R O G L D O W R W K H G H V L U H G V S H H G
7 X U Q R Q W K H D L U F R Q G L W L R Q H U E \ S U H V V L Q J
W K H $ & V Z L W F K
$ I W H U F R R O L Q J E H J L Q V D G M X V W W K H I D Q
F R Q W U R O G L D O D Q G W H P S H U D W X U H F R Q W U R O
G L D O D V Q H H G H G W R P D L Q W D L Q P D [ L P X P
F R P I R U W
& $ 8 7 , 2 1
If the air conditioner is used while driving
up long hills or in heavy traffic, monitor the
high engine coolant temperature warning
light to see if it is illuminated or flashing
(page 4-38).
The air conditioner may cause engine
overheating. If the warning light is
illuminated or flashing, turn the air
conditioner off (page 7-28).
NOTE
x(Type A)
When maximum cooling is desired, set
the temperature control dial to the
extreme cold position and set the air
intake selector to the recirculated air
position, then turn the fan control dial
fully clockwise.
x(Type C/Type D)
When maximum cooling is desired, set the
temperature control dial to the extreme cold
position and set the air intake selector to the
recirculated air position, then set the fan
control dial to position 4.
x(Type A/Type C)
If warmer air is desired at floor level, set the
mode selector dial to the
position and adjust
the temperature control dial to maintain
maximum comfort.
xThe air to the floor is warmer than air
to the face (except when the temperature
control dial is set at the extreme hot or
cold position).
▼ 9 H Q W L O D W L R Q
6 H W W K H P R G H V H O H F W R U G L D O W R W K H
S R V L W L R Q
7 \ S H $ 7 \ S H %
6 H W W K H D L U L Q W D N H V H O H F W R U W R W K H R X W V L G H
D L U S R V L W L R Q
7 \ S H & 7 \ S H '
6 H W W K H D L U L Q W D N H V H O H F W R U W R W K H
S R V L W L R Q
6 H W W K H W H P S H U D W X U H F R Q W U R O G L D O W R W K H
G H V L U H G S R V L W L R Q
6 H W W K H I D Q F R Q W U R O G L D O W R W K H G H V L U H G
V S H H G
▼ : L Q G V F U H H Q ' H I U R V W L Q J D Q G
' H I R J J L Q J
6 H W W K H P R G H V H O H F W R U G L D O W R W K H
S R V L W L R Q
7 \ S H & 7 \ S H '
6 H W W K H D L U L Q W D N H V H O H F W R U W R W K H
S R V L W L R Q
6 H W W K H W H P S H U D W X U H F R Q W U R O G L D O W R W K H
G H V L U H G S R V L W L R Q
6 H W W K H I D Q F R Q W U R O G L D O W R W K H G H V L U H G
V S H H G
7 \ S H $ 7 \ S H &
, I G H K X P L G L I L H G K H D W L Q J L V G H V L U H G W X U Q
R Q W K H D L U F R Q G L W L R Q H U
7 \ S H '
3 U H V V W K H $ & V Z L W F K W R W X U Q R Q W K H D L U
F R Q G L W L R Q H U
, Q W H U L R U ) H D W X U H V
$ L U & R Q G L W L R Q L Q J 6 \ V W H P
Page 551 of 759
& $ 8 7 , 2 1
¾To prevent accessory socket damage or
electrical failure, pay attention to the
following:
¾Do not use accessories that require
more than 120 W (DC 12 V, 10 A).
¾Do not use accessories that are not
genuine Mazda accessories or the
equivalent.
¾Close the cover when the accessory
socket is not in use to prevent foreign
objects and liquids from getting into
the accessory socket.
¾Correctly insert the plug into the
accessory socket.
¾Do not insert the cigarette lighter into
the accessory socket.
¾Noise may occur on the audio playback
depending on the device connected to
the accessory socket.
¾Depending on the device connected to
the accessory socket, the vehicle's
electrical system may be affected, which
could cause the warning light to
illuminate. Disconnect the connected
device and make sure that the problem is
resolved. If the problem is resolved,
disconnect the device from the socket
and switch the ignition
off. If the problem
is not resolved, consult an expert repairer
(we recommend an Authorised Mazda
Repairer).
NOTE
To prevent discharging of the battery, do
not use the socket for long periods with the
engine off or idling.
& X S + R O G H U
: $ 5 1 , 1 *
Never use a cup holder to hold hot liquids
while the vehicle is moving:
Using a cup holder to hold hot liquids while
the vehicle is moving is dangerous. If the
contents spill, you could be scalded.
Do not put anything other than cups or
drink cans in cup holders:
Putting objects other than cups or drink
cans in a cup holder is dangerous.
During sudden braking or manoeuvring,
occupants could be hit and injured, or
objects could be thrown around the
vehicle, causing interference with the driver
and the possibility of an accident. Only use
a cup holder for cups or drink cans.
, Q W H U L R U ) H D W X U H V
, Q W H U L R U ( T X L S P H Q W
Page 582 of 759
& $ 8 7 , 2 1
¾Using oils of viscosity besides those recommended for
specific temperature ranges could
result in engine damage.
¾(SKYACTIV-D 1.5)
SKYACTIV-D 1.5 uses specified oil. Please confirm the specification in owner's manual. If
engine oil other than the
specified oil is used, the Diesel Particulate Filter
effective period of
use will be shortened or the Diesel Particulate Filter may be damaged.
NOTE
(SKYACTIV-G 1.3 and SKYACTIV-G 1.5)
xIt is normal for all engines to consume engine oil under normal driving conditions.
Engine oil consumption may be as high as 0.8 L/1,000 km (1 L/800 miles). This may be as
a result of evaporation, internal ventilation or burning of the lubricating oil in the
working engine. Oil consumption may be higher when the engine is new due to the
running-in process. Oil consumption is also dependant on engine speed and engine load.
Under extreme driving conditions, oil consumption may be higher.
(SKYACTIV-D 1.5)
xInspect the engine oil level periodically. When inspecting the engine oil, if the engine oil
level is exceeds the “X” mark on the dipstick, replace the engine oil. This should be done
by an expert repairer (we recommend an Authorised Mazda Repairer). When replacing
the engine oil, inspect the oil level using the oil dipstick and refill so that the engine oil
level is within the range between MIN and MAX as shown in the figure.
X Mark MAX MIN
xWhenever the engine oil is replaced, the vehicles engine control unit needs to be reset as
soon as possible. Otherwise the wrench indicator light or engine oil warning light may
turn on. To reset the engine control unit, consult an expert repairer (we recommend an
Authorised Mazda Repairer) or refer to the vehicle engine control unit reset procedure on
page 6-27.
0 D L Q W H Q D Q F H D Q G & D U H
2 Z Q H U 0 D L Q W H Q D Q F H
Page 583 of 759
▼ 9 H K L F O H ( Q J L Q H & R Q W U R O 8 Q L W 5 H V H W 3 U R F H G X U H
NOTE
This procedure is intended for vehicles with SKYACTIV-D 1.5 and vehicles with
SKYACTIV-G 1.3 or SKYACTIV-G 1.5 which the engine oil flexible maintenance setting is
selected.
$ I W H U U H S O D F L Q J W K H H Q J L Q H R L O K D Y H D U H S D L U V K R S V X F K D V D Q $ X W K R U L V H G 0 D ] G D 5 H S D L U H U
S H U I R U P W K H L Q L W L D O L ] D W L R Q H Q J L Q H R L O G D W D U H V H W W L Q J R I W K H U H F R U G H G Y D O X H , I W K H Y D O X H
U H F R U G H G E \ W K H F R P S X W H U L V Q R W L Q L W L D O L ] H G W K H Z U H Q F K L Q G L F D W R U O L J K W P D \ Q R W W X U Q R I I R U L W
P D \ W X U Q R Q H D U O L H U W K D Q Q R U P D O
NOTE
The initialization (engine oil data resetting) of the recorded value can be performed using
the following procedure:
1. Switch the ignition OFF.
2. Switch the ignition ON with the selector pressed and continue pressing the selector for
about 5 seconds until the master warning light
flashes.
Selector
3. After the master warning light flashes for several seconds, the initialization is
completed.
0 D L Q W H Q D Q F H D Q G & D U H
2 Z Q H U 0 D L Q W H Q D Q F H
Page 628 of 759
![MAZDA MODEL 2 2019 (in English) Owners Guide 3 D U N L Q J L Q D Q ( P H U J H Q F \
7 K H K D ] D U G Z D U Q L Q J O L J K W V V K R X O G D O Z D \ V
E H X V H G Z K H Q \ R X V W R S R Q R U Q H D U D
U R](/img/28/15645/w960_15645-627.png "MAZDA MODEL 2 2019 (in English) Owners Guide 3 D U N L Q J L Q D Q ( P H U J H Q F \
7 K H K D ] D U G Z D U Q L Q J O L J K W V V K R X O G D O Z D \ V
E H X V H G Z K H Q \ R X V W R S R Q R U Q H D U D
U R")
3 D U N L Q J L Q D Q ( P H U J H Q F \
7 K H K D ] D U G Z D U Q L Q J O L J K W V V K R X O G D O Z D \ V
E H X V H G Z K H Q \ R X V W R S R Q R U Q H D U D
U R D G Z D \ L Q D Q H P H U J H Q F \
7 K H K D ] D U G Z D U Q L Q J O L J K W V Z D U Q R W K H U
G U L Y H U V W K D W \ R X U Y H K L F O H L V D W U D I I L F K D ] D U G
D Q G W K D W W K H \ P X V W W D N H H [ W U H P H F D X W L R Q
Z K H Q Q H D U L W
' H S U H V V W K H K D ] D U G Z D U Q L Q J I O D V K H U D Q G D O O
W K H G L U H F W L R Q L Q G L F D W R U V Z L O O I O D V K 7 K H
K D ] D U G Z D U Q L Q J L Q G L F D W R U O L J K W V L Q W K H
L Q V W U X P H Q W F O X V W H U I O D V K V L P X O W D Q H R X V O \
NOTE
xThe direction indicators do not work
when the hazard warning lights are on.
xCheck local regulations about the use of
hazard warning lights while the vehicle
is being towed to verify that it is not in
violation of the law.
5 R D G V L G H ( P H U J H Q F \
7 U L D Q J O H 5 H W D L Q L Q J 6 W U D S
+ D W F K E D F N
. H H S W K H U R D G V L G H H P H U J H Q F \ W U L D Q J O H L Q
W K H U L J K W V L G H W U L P D Q G V H F X U H L W Z L W K W K H
V W U D S
Strap
, I 7 U R X E O H $ U L V H V
3 D U N L Q J L Q D Q ( P H U J H Q F \
6 R P H P R G H O V
Page 640 of 759
NOTE
Do not throw away the empty tyre
sealant bottle after use. Return the
empty tyre sealant bottle to an
Authorised Mazda Repairer when
replacing the tyre. The empty tyre
sealant bottle will need to be used to
extract and dispose of the used sealant
from the tyre.
$ I W H U W K D W L Q V W D O O W K H L Q M H F W L R Q K R V H W R
W K H W D E R I W K H E R W W O H W R S U H Y H Q W O H D N D J H
R I D Q \ U H P D L Q L Q J V H D O D Q W
Tab
$ W W D F K W K H Y H K L F O H V S H H G U H V W U L F W L R Q
V W L F N H U L Q D S O D F H Z K H U H W K H G U L Y H U F D Q
H D V L O \ V H H L W
: $ 5 1 , 1 *
Do not attach the vehicle speed
restriction sticker to the instrument
panel, as it would obstruct vision of
areas such as warning light indicators
or the speedometer:
Attaching the vehicle speed restriction
sticker to the steering wheel pad is
dangerous. The sticker could interfere
with air bag inflation and cause serious
injury.
, Q V W D O O W K H F R P S U H V V R U K R V H W R W K H W \ U H
Y D O Y H
Valve
Compressor hose
, Q V H U W W K H F R P S U H V V R U S O X J L Q W R W K H
L Q W H U L R U D F F H V V R U \ V R F N H W D Q G V Z L W F K
W K H L J Q L W L R Q W R $ & &
Compressor
Compressor plug
, I 7 U R X E O H $ U L V H V
) O D W 7 \ U H
Page 641 of 759
& $ 8 7 , 2 1
¾Before pulling out the compressor
plug from the electrical socket, make
sure the compressor power switch is
off.
¾The compressor turns on and off with
the push-button switch.
7 X U Q W K H F R P S U H V V R U V Z L W F K R Q D Q G
L Q I O D W H W K H W \ U H F D U H I X O O \ W R W K H F R U U H F W
L Q I O D W L R Q S U H V V X U H
: $ 5 1 , 1 *
Never operate the compressor above
300 kPa (3.1 kgf/cm
2, 3 bar, 43.5 psi):
Operating the compressor above 300
kPa (3.1 kgf/cm
2, 3 bar, 43.5 psi) is
dangerous. When the inflation pressure
rises above 300 kPa (3.1 kgf/cm
2, 3 bar,
43.5 psi), heated air will be exhausted
from the back of the compressor and
you could be burned.
NOTE
xCheck the tyre inflation pressure
label (driver's door frame) for the
correct tyre inflation pressure.
xDo not use the compressor for
longer than 10 minutes because
using the compressor for long
periods could damage it.
xIf the tyre does not inflate, repair of
the tyre may not be possible. If the
tyre does not reach the correct
inflation pressure within a 10-minute
period, it probably has received
more extensive damage.
When this happens, the emergency
flat tyre repair kit cannot be used to
repair the tyre. Contact an expert
repairer (we recommend an
Authorised Mazda Repairer).
xIf the tyre has been over-inflated,
loosen the screw cap on the
compressor and bleed some of the
air out.
: K H Q W K H W \ U H K D V E H H Q L Q I O D W H G W R W K H
S U R S H U L Q I O D W L R Q S U H V V X U H W X U Q W K H
F R P S U H V V R U V Z L W F K R I I D Q G U H P R Y H W K H
F R P S U H V V R U K R V H I U R P W K H W \ U H Y D O Y H
, Q V W D O O W K H W \ U H Y D O Y H F D S
3 X W W K H H P H U J H Q F \ I O D W W \ U H U H S D L U N L W L Q
W K H O X J J D J H F R P S D U W P H Q W E R R W D Q G
F R Q W L Q X H G U L Y L Q J
& $ 8 7 , 2 1
¾Drive carefully to an expert repairer
(we recommend an Authorised
Mazda Repairer) and keep the vehicle
speed below 80 km/h (50 mph).
¾If the vehicle is driven 80 km/h (50
mph) or higher, the vehicle might
begin to vibrate.
NOTE
(With tyre pressure monitoring
system)
If the tyre is not properly inflated, the
tyre pressure monitoring system
warning light will illuminate.
$ I W H U G U L Y L Q J W K H Y H K L F O H I R U
P L Q X W H V R U N P P L O H V F K H F N W K H
W \ U H S U H V V X U H Z L W K W K H W \ U H S U H V V X U H
J D X J H H T X L S S H G Z L W K W K H F R P S U H V V R U , I
W K H W \ U H S U H V V X U H K D V I D O O H Q E H O R Z W K H
F R U U H F W W \ U H S U H V V X U H L Q I O D W H W K H W \ U H W R
W K H F R U U H F W S U H V V X U H D J D L Q I R O O R Z L Q J
W K H V W H S V I U R P Q X P E H U
, I 7 U R X E O H $ U L V H V
) O D W 7 \ U H