ECU MAZDA MODEL 3 HATCHBACK 2015 (in English) Owner's Guide

3–49
Before Driving
Security System
To cancel the intrusion sensor, press
the intrusion sensor cancel button on
the transmitter within 20 seconds after
pressing the lock button.
The hazard warning lights will fl ash three
times.
NOTE
  To reactivate the intrusion sensor,
turn off the armed theft-deterrent
system and then rearm it.
  The intrusion sensor is operational
when the theft-deterrent system
is armed. To cancel the intrusion
sensor, press the intrusion sensor
cancel button each time the theft-
deterrent system is armed.
To Turn Off an Armed System
An armed system can be turned off using
any one of the following methods:
 


 Pressing the unlock button or the boot
button (saloon) on the transmitter.
 


 Starting the engine with the push button
start.
 


(With the advanced keyless function)



 
 Pressing a request switch on the doors.


 
 Pressing the electric liftgate/boot lid
opener while the key is being carried.
The hazard warning lights will fl ash twice.
NOTE
When the doors are unlocked by
pressing the unlock button on the
transmitter while the theft-deterrent
system is turned off, the hazard warning
lights will fl ash twice to indicate that the
system is turned off.
To Stop the Alarm
A triggered alarm can be turned off using
any one of the following methods:
 


 Pressing the unlock button or the boot
button (saloon) on the transmitter.
 


 Starting the engine with the push button
start.
 


(With the advanced keyless function)



 
 Pressing a request switch on the doors.


 
 Pressing the electric liftgate/boot lid
opener while the key is being carried.
The hazard warning lights will fl ash twice.
Theft-Deterrent Labels
A label indicating that your vehicle is
equipped with a Theft-Deterrent System is
in the glove compartment.
Mazda recommends that you affi x it to the
lower rear corner of a front door window.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.3–50
Before Driving
Security System
Theft-Deterrent System
(Without the Intrusion
Sensor)
*
If the theft deterrent system detects an
inappropriate entry into the vehicle,
which could result in the vehicle or its
contents being stolen, the alarm alerts the
surrounding area of an abnormality by
sounding the horn and fl ashing the hazard
warning lights.
The system will not function unless it's
properly armed. So when you leave the
vehicle, follow the arming procedure
correctly.
Operation
System triggering conditions
The horn sounds intermittently and the
hazard warning lights fl ash for about 30
seconds when the system is triggered by
any one of the following:
 


 Unlocking a door with the key or an
inside door-lock knob.
 


 Forcing open a door, the bonnet or the
liftgate/boot lid.
 


 Opening the bonnet by operating the
bonnet release handle.
 


 Switching the ignition ON without using
the push button start.
If the system is triggered again, the lights
and horn will activate until the driver's
door or the liftgate/boot lid is unlocked
with the transmitter.
(With advanced key)
The lights and horn can also be
deactivated by pressing the request switch
on a door.
NOTE
If the battery goes dead while the theft-
deterrent system is armed, the horn will
activate and the hazard warning lights
will fl ash when the battery is charged or
replaced.
How to Arm the System
1. Close the windows and the sunroof *
securely.
2. Switch the ignition OFF.
3. Make sure the bonnet, the doors, and
the liftgate/boot lid are closed.
4. Press the lock button on the transmitter
or lock the driver's door from the
outside with the auxiliary key.
The hazard warning lights will fl ash
once.
(With the advanced keyless function)
Press a request switch.
The security indicator light in the
instrument panel fl ashes twice per
second for 20 seconds.
5. After 20 seconds, the system is fully
armed.
.B[EB@&'&&"@&EJUJPOJOEC







3–51
Before Driving
Security System
NOTE
  The theft deterrent system can also
be armed by activating the auto
relock function with all the doors,
the liftgate/boot lid and the bonnet
closed.
 Refer to Transmitter on page 3-4 .   The system will disarm if one of
the following operations takes place
within 20 seconds after pressing the
lock button:
 


 Unlocking any door.



 Opening any door or the liftgate/
boot lid.
 


 Opening the bonnet.



 Switching the ignition ON.



(With the advanced keyless
function)
  Pressing the electric liftgate/boot
lid opener while the key is being
carried.
  To rearm the system, do the arming
procedure again.
  When the doors are locked by
pressing the lock button on the
transmitter or using the auxiliary key
while the theft-deterrent system is
armed, the hazard warning lights will
fl ash once to indicate that the system
is armed.
To Turn Off an Armed System
An armed system can be turned off using
any one of the following methods:
 


 Pressing the unlock button on the
transmitter.
 


 Switching the ignition ON.



(With the advanced keyless function)
 Pressing a request switch on the doors.
The hazard warning lights will fl ash twice.
NOTE
When the doors are unlocked by
pressing the unlock button on the
transmitter while the theft-deterrent
system is turned off, the hazard warning
lights will fl ash twice to indicate that the
system is turned off.
To Stop an Alarm
A triggered alarm can be turned off using
any one of the following methods:
 


 Pressing the unlock button or the boot
button (saloon) on the transmitter.
 


 Starting the engine with the push button
start.
(With the advanced keyless function)
 


 Pressing a request switch on the doors.



 Pressing the electric liftgate/boot lid
opener while the key is being carried.
The hazard warning lights will fl ash twice.
.B[EB@&'&&"@&EJUJPOJOEC







3–52
Before Driving
Security System
Theft-Deterrent Labels
A label indicating that your vehicle is
equipped with a Theft-Deterrent System is
in the glove compartment.
Mazda recommends that you affi x it to the
lower rear corner of a front door window.
.B[EB@&'&&"@&EJUJPOJOEC







3–55
Before Driving
Driving Tips
Floor Mat
WARNING
Make sure the fl oor mats are secured
with the grommets or the retainers to
prevent them from bunching up under
the foot pedals (Driver's side):
Using a fl oor mat that is not secured is
dangerous as it will interfere with the
accelerator and brake pedal operation
(driver's side), which could result in an
accident.
Only use a fl oor mat which conforms
to the shape of the fl oor on the driver's
side and make sure it is oriented
correctly.
Secure the fl oor mat using the
grommets or retainers.
There are various ways to secure fl oor
mats depending on the type used,
therefore secure the mat according to
the type.
After installing the fl oor mat, make
sure that it does not slide from side
to side or back and forth, and that
there is suffi cient clearance with the
accelerator and brake pedals on the
driver's side.
After removing the fl oor mat for
cleaning or some other reason, always
securely reinstall it while paying
attention to the precautions just
mentioned.
WARNING
Do not install two fl oor mats, one on
top of the other, on the driver's side:
Installing two fl oor mats, one on top
of the other, on the driver's side is
dangerous as the retention pins can
only keep one fl oor mat from sliding
forward.
Loose fl oor mat(s) will interfere with
the foot pedals and could result in an
accident.
When using a heavy duty fl oor mat for
winter, always remove the original fl oor
mat.
When setting a fl oor mat, position the
fl oor mat so that its grommets or retainers
are inserted over the pointed end of the
retention posts.
.B[EB@&'&&"@&EJUJPOJOEC







3–58
Before Driving
Driving Tips
NOTE
If your vehicle is equipped with the tyre
pressure monitoring system, the system
may not function correctly when using
tyre chains.
Install the chains on the front tyres only.
Do not use chains on the rear tyres.
Tyre chain selection (Europe)
Mazda recommends hexagon type
steel ring chains. Select the proper type
according to your tyre size.
Tyre size Tyre chain
205/60R16 Hexagon type
215/45R18 Hexagon type
215/45ZR18 Hexagon type
NOTE
Although Mazda recommends hexagon
type steel ring chains, all chains within
the installation specifi cations may be
used.
Installation specifi cation (Europe)
When installing tyre chains, the distance
between the tyre tread and the chain must
be within the prescribed limits in the
following table.
Distance [Unit: mm (in)]
A B
MAX 11 (0.43) MAX 11 (0.43)
Side viewCross section viewTyre A
B
Installing the chains
1. If your vehicle is equipped with wheel
covers remove them, otherwise the
chain bands will scratch them.
2. Secure the chains on the front tyres as
tightly as possible. Always follow the
chain manufacturer's instructions.
3. Retighten the chains after driving
1/2—1 km (1/4—1/2 mile).
.B[EB@&'&&"@&EJUJPOJOEC







3–67
Before Driving
Towing
Trailer Hitch
When towing a trailer, use an appropriate trailer hitch. We recommend using a genuine
Mazda trailer hitch. Use the original holes drilled by the vehicle manufacture for securing
the trailer hitch. Contact your Authorised Mazda Dealer for more information.
C
Unit:mm(in)
A
BCA:350—420 (13.8—16.5)
B:1049.3 (41.311)
C:1046.9 (41.217) Trailer hitch installation area (Saloon)
MAX 75 Kg (165 lb)
Hitch coupling point
.B[EB@&'&&"@&EJUJPOJOEC







3–69
Before Driving
Towing
Safety Chains
Safety chains must be used as a precautionary measure should the trailer become
unintentionally unhitched. They should cross under the trailer tongue and attach to the hitch.
Leave enough slack to allow full turns. Consult literature published by your trailer or hitch
manufacturer for more details.
WARNING
Make sure the safety chain is securely attached to both the trailer and the vehicle prior
to departure:
Towing a trailer without using a safety chain securely attached to both the trailer and
the vehicle is dangerous. If damage occurs to the coupling unit or hitch ball, the trailer
could wander into another lane and cause a collision.
Trailer Lights
CAUTION
Do not connect a trailer lighting system directly to the lighting system of your Mazda.
This may damage your vehicle's electrical system and lighting systems. To connect the
lighting system, consult an Authorised Mazda Dealer.
Trailer Brakes
Check the Maximum trailer towing-load table in Weight Limits (page 3-61 ), and if your
trailer weight exceeds the value in the TOTAL TRAILER WEIGHT (Trailer without brake),
trailer brakes are required.
If your trailer has brakes, make sure they meet regulations.
WARNING
Do not connect a hydraulic trailer-brake system to your vehicle's brake system:
Connecting a hydraulic trailer-brake system directly to the vehicle brake system is
dangerous and will result in inadequate braking and possible injury.
.B[EB@&'&&"@&EJUJPOJOEC







3–70
Before Driving
Towing
Trailer Towing Tips
Before driving
 




 Verify that your Mazda maintains a near-normal attitude when a loaded or unloaded trailer
is connected. Do not drive if it has an abnormal front-up or front-down position. Inspect
for incorrect nose weight, worn suspension parts, and trailer overloading. Have the vehicle
inspected by an expert repairer, we recommend an Authorised Mazda Repairer.
 


 Make sure the trailer cargo is secure to prevent it from shifting.



 Make sure the mirrors meet all government regulations. Inspect them.



 Before starting out, inspect the operation of all vehicle and trailer lights and all vehicle-
to-trailer connections. Stop and re-inspect all lights and connections after driving a short
distance.
Driving
 




 Your Mazda will handle differently with a trailer in tow, so practice turning, backing, and
stopping in a traffi c-free area.




 Take time to get accustomed to the extra weight and length.



 Do not exceed 100 km/h (62 mph) with a trailer in tow. If the local legal maximum speed
with a trailer in tow is less than 100 km/h (62 mph), do not exceed the legal speed.
CAUTION
If the vehicle exceeds 100 km/h (62 mph) with a trailer in tow, the vehicle could be
damaged.
 


 When ascending a hill, shift into a lower gear to reduce the possibility of overloading or
overheating the engine, or both.
 


 When descending a hill, shift into a lower gear and use engine compression as a braking
effect. Pay constant attention to speed and use the brakes only as needed. Holding the
brake pedal down for a prolonged period may cause the brakes to overheat and lose
power.
.B[EB@&'&&"@&EJUJPOJOEC







4–4
When Driving
Start/Stop Engine
Ignition Switch
Push Button Start Positions
The system operates only when the driver
is in the vehicle or within operational
range while the key is being carried.
Each time the push button start is pressed,
the ignition switches in the order of off,
ACC, and ON. Pressing the push button
start again from ON switches the ignition
off.
Indicator light
Push button start
NOTE
  The engine starts by pressing the
push button start while depressing
the clutch pedal (manual transaxle)
or the brake pedal (automatic
transaxle). To switch the ignition
position, press the push button start
without depressing the pedal.
  Do not leave the ignition switched
ON while the engine is not running.
Doing so could result in the battery
going dead. If the ignition is left in
ACC (For automatic transaxle, the
selector lever is in the P position, and
the ignition is in ACC), the ignition
switches off automatically after about
25 minutes. Off
The power supply to electrical devices
turns off and the push button start indicator
light (amber) also turns off.
In this position the steering wheel is
locked.
WARNING
Before leaving the driver's seat, always
switch the ignition off, set the parking
brake, and make sure the selector lever
is in P (automatic transaxle) or in 1st
gear or R (manual transaxle):
Leaving the driver's seat without
switching the ignition off, setting the
parking brake, and shifting the selector
lever to P (automatic transaxle) or
to 1st gear or R (manual transaxle)
is dangerous. Unexpected vehicle
movement could occur which could
result in an accident.
In addition, if your intention is to leave
the vehicle for even a short period, it
is important to switch the ignition off,
as leaving it in another position will
disable some of the vehicle's security
systems and run the battery down.
NOTE
(Locked steering wheel)
If the push button start indicator light
(green) is fl ashing and the beep sound
is heard, this indicates that the steering
wheel is not unlocked. To unlock the
steering wheel, press the push button
start while moving the steering wheel
left and right.
.B[EB@&'&&"@&EJUJPOJOEC