brakes MAZDA MODEL 6 2004 (in English) User Guide
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2004, Model line: MODEL 6, Model: MAZDA MODEL 6 2004Pages: 289, PDF Size: 7.22 MB
Page 115 of 289
5-16
Driving Your Mazda
Starting and Driving
Form No. 8R29-EA-02I
Downshifting
When you must slow down in heavy
traffic or on a steep upgrade
, downshift
before the engine starts to overwork. This
gives better acceleration when you need
more speed.
On a steep downgrade
, downshifting
helps maintain safe speed and prolongs
brake life.
Driving Tips
Passing
For extra power when passing another
vehicle or climbing steep grades, depress
the accelerator fully. The transaxle will
shift to a lower gear, depending on vehicle
speed.
Climbing steep grades from a stop
To climb a steep grade from a stopped
position:
1. Depress the brake pedal.
2. Shift to D or M1, depending on the
load weight and grade steepness.
3. Release all brakes while gradually
accelerating.
Descending steep grades
When descending a steep grade, shift to
lower gears, depending on load weight
and grade steepness. Descend slowly,
using the brakes only occasionally to
prevent them from overheating.Power steering is only operable when the
engine is running. If the engine is off or if
the power steering system is inoperable,
you can still steer, but it requires more
physical effort.
If the steering feels rigid during normal
driving, consult an Authorized Mazda
Dealer.
Power Steering
Never hold the steering wheel to the
extreme left or right for more than 5
seconds with the engine running.
This could damage the power steering
system.
CAUTION
shuseizumi_J56J_8R29_EA_02I.book Page 16 Saturday, September 7, 2002 12:58 PM
Page 128 of 289
5-29
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R29-EA-02I
Brake System Warning Light
This warning has the following functions:
Parking brake warning
The light comes on when the parking
brake is applied with the ignition switch
in the START or ON position. It goes off
when the parking brake is fully released.
Low brake fluid level warning/
Electronic brake force distribution system warning
If the light stays on after the parking brake
is fully released, you may have a brake
problem.
Drive to the side of the road and park off
the right-of-way.
Low brake fluid level warning
You may notice that the pedal is harder to
push or that it may go closer to the floor.
In either case, it will take longer to stop
the vehicle.
1. With the engine stopped, check the
brake fluid level immediately and add
fluid as required (page 8-15).
2. After adding fluid, check the light
again.If the warning light remains on, or if the
brakes do not operate properly, do not
drive the vehicle. Have it towed to an
Authorized Mazda Dealer.
Even if the light goes off, have your brake
system inspected as soon as possible.
Electronic brake force distribution
system warning
If the electronic brake force distribution
control unit determines that some
components are operating incorrectly, the
control unit may turn the brake system
warning light on.
In this case, the ABS warning light comes
on at the same time (page 5-31).
shuseizumi_J56J_8R29_EA_02I.book Page 29 Saturday, September 7, 2002 12:58 PM
Page 129 of 289
5-30
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R29-EA-02I
Charging System Warning Light
This warning light comes on when the
ignition switch is turned to the ON
position and goes off when the engine is
started.
If the warning light comes on while
driving, it indicates a malfunction of the
alternator or of the charging system.
Drive to the side of the road and park off
the right-of-way. Consult an Authorized
Mazda Dealer.
Engine Oil Pressure Warning
Light
This warning light indicates low engine
oil pressure.
If the light comes on while driving:
1. Drive to the side of the road and park
off the right-of-way.
Brake Warning Light:Driving with the brake system
warning light on is dangerous. It
indicates that your brakes may not
work at all or that they could
completely fail at any time. If this
light remains on, after checking that
the parking brake is released, have
the brakes inspected immediately.
Don’t drive with this light on, and
contact an Authorized Mazda Dealer
to have the brakes inspected as soon
as possible.
ABS Warning Light and Brake
Warning Light on at the Same Time:Driving when the brake system
warning light and ABS warning light
are on at the same time is dangerous.
When both lights are on, the rear
wheels could lock more quickly in an
emergency stop than under normal
circumstances.
Don’t drive with both lights on, and
contact an Authorized Mazda Dealer
to have the brakes inspected as soon
as possible.
WARNING
Don’t continue driving when the
charging system warning light is
illuminated.
CAUTION
shuseizumi_J56J_8R29_EA_02I.book Page 30 Saturday, September 7, 2002 12:58 PM
Page 130 of 289
5-31
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8R29-EA-02I
2. Turn off the engine and inspect the
engine oil level (page 8-10). If it’s low,
add oil.
3. Check the light.
If the light remains on even after you add
oil, have your vehicle towed to the nearest
service station or to an Authorized Mazda
Dealer.
Check Engine Light
If this light comes on while driving, the
vehicle may have a problem. It is
important to note the driving conditions
when the light came on and consult an
Authorized Mazda Dealer.
The check engine light may come on in
the following cases:
•
The fuel tank level being very low or
approaching empty.
•
The engine’s electrical system has a
problem.
•
The emission control system has a
problem.
•
The fuel-filler cap is missing or not
tightened securely.If the check engine light remains on, do
not drive at high speeds and consult an
Authorized Mazda Dealer as soon as
possible.
ABS Warning Light
The warning light stays on for a few
seconds when the ignition switch is turned
to the ON position.
If the ABS warning light stays on while
you’re driving, the ABS control unit has
detected a system malfunction. If this
occurs, your brakes will function
normally as if the vehicle had no ABS.
Should this happen, consult an Authorized
Mazda Dealer as soon as possible. Don’t run the engine if oil pressure is
low. It could result in extensive engine
damage.
CAUTION
ABS Warning Light and Brake Warning Light on at the Same Time:Driving when the brake system
warning light and ABS warning light
are on at the same time is dangerous.
When both lights are on, the rear
wheels could lock more quickly in an
emergency stop than under normal
circumstances.
Don’t drive with both lights on, and
contact an Authorized Mazda Dealer
to have the brakes inspected as soon
as possible.
WARNING
shuseizumi_J56J_8R29_EA_02I.book Page 31 Saturday, September 7, 2002 12:58 PM
Page 222 of 289
8-3
Maintenance and Care
Form No. 8R29-EA-02I
Scheduled Maintenance
Follow Schedule 1 if the vehicle is operated mainly where none of the following conditions
apply.
If any do apply, follow Schedule 2 (Canada and Puerto Rico residents follow Schedule 2).
•
Repeated short-distance driving
•
Driving in dusty conditions
•
Driving with extended use of brakes
•
Driving in areas where salt or other corrosive materials are being used
•
Driving on rough or muddy roads
•
Extended periods of idling or low-speed operation
•
Driving for long periods in cold temperatures or extremely humid climates
Scheduled Maintenance
NOTE
After the prescribed period, continue to follow the described maintenance at the
recommended intervals.
shuseizumi_J56J_8R29_EA_02I.book Page 3 Saturday, September 7, 2002 12:58 PM
Page 223 of 289
8-4
Maintenance and Care
Scheduled Maintenance
Form No. 8R29-EA-02I
Schedule 1
I: Inspect and repair, clean, adjust, or replace if necessary.
R: Replace
L: Lubricate
ENGINE
COOLING SYSTEM
FUEL SYSTEM
IGNITION SYSTEM
CHASSIS and BODY
AIR CONDITIONER SYSTEM (if installed)
*1According to state/provincial and federal regulations, failure to perform maintenance on these items will not
void your emissions warranties. However, Mazda recommends that all maintenance services be performed at
the recommended time or mileage/kilometer period to ensure long-term reliability. Maintenance Interval
(Number of months or
kilometers (miles),
whichever comes first)Months 6 12182430364248
×1000 km 12 24 36 48 60 72 84 96
×1000 miles 7.5 15 22.5 30 37.5 45 52.5 60
Drive belts (tension) 2.3-liter engine
I
3.0-liter engine
II
Engine oil
RRRRRRRR
Engine oil filter
RRRRRRRR
Cooling system
II
Engine coolantReplace at first 168,000km (105,000miles) or 60 months ;
after that, every 48,000km (30,000miles) or 24 months
Air filter
R
Fuel lines and hoses
*1II
Hoses and tubes for emission*1I
Spark plugs
Replace every 120,000km (75,000miles)
Brake lines, hoses and connections
II
Disc brakes
IIII
Steering operation and linkages
II
Front suspension ball joints
II
Driveshaft dust boots
II
Bolts and nuts on chassis and body
II
Exhaust system heat shields
II
All locks and hinges
LLLLLLLL
Cabin air filter
Replace every 40,000km (25,000miles) or 24 months
shuseizumi_J56J_8R29_EA_02I.book Page 4 Saturday, September 7, 2002 12:58 PM
Page 225 of 289
8-6
Maintenance and Care
Scheduled Maintenance
Form No. 8R29-EA-02I
I: Inspect and repair, clean, adjust, or replace if necessary.
L: Lubricate
CHASSIS and BODY
AIR CONDITIONER SYSTEM (if installed)Maintenance Interval
(Number of months or
kilometers (miles),
whichever comes first)
Months 4 8 12 16 20 24 28 32 36 40 44 48
×1000 km 8 16 24 32 40 48 56 64 72 80 88 96
×1000 miles 5 10 15 20 25 30 35 40 45 50 55 60
Brake lines, hoses and connections
II
Brake and clutch fluid level
IIIIIIIIIIII
Disc brakes
IIII
Tire inflation pressure and tire wear
IIIIIIIIIIII
Steering operation and linkages
II
Power steering fluid level
IIIIIIIIIIII
Front suspension ball joints
II
Driveshaft dust boots
II
Bolts and nuts on chassis and body
IIII
Exhaust system heat shields
II
All locks and hinges
LLLLLLLLLLLL
Washer fluid level
IIIIIIIIIIII
Cabin air filter
Replace every 40,000km (25,000miles) or 24 months
shuseizumi_J56J_8R29_EA_02I.book Page 6 Saturday, September 7, 2002 12:58 PM
Page 234 of 289
8-15
Maintenance and Care
Owner Maintenance
Form No. 8R29-EA-02I
2. Only when the engine is cool, remove
the radiator drain plug and drain the
coolant into a suitable container.
Properly dispose of the used coolant.
3. Flush out the system with running
water.
4. Drain the system completely. Insert
and tighten the plug. Add as much
ethylene-glycol-based coolant and
water as necessary to provide freezing
and corrosion protection.
5. In extremely cold climates, add the
amount recommended in the coolant
manufacturer’s instructions.
6. Run the engine at idle with the cooling
system cap off. Slowly add additional
coolant if necessary.
7. At this point, wait until the engine
reaches normal operating temperature;
then depress the accelerator two or
three times. Add more coolant, if
necessary, until the system is full.
8. Install the cooling system cap. Inspect
all connections for leaks. Inspect the
level in the coolant reservoir one more
time.
Inspecting Brake/Clutch Fluid
Level
The brakes and clutch draw fluid from the
same reservoir.
Inspect the fluid level in the reservoir
regularly. It should be kept at MAX.
The level normally drops with
accumulated distance, a condition
associated with wear of brake and clutch
linings. If it is excessively low, have the
brake/clutch system inspected by an
Authorized Mazda Dealer.
Loosen
Tighten
Loosen Tighten
3.0-liter engine
Brake/Clutch Fluid
shuseizumi_J56J_8R29_EA_02I.book Page 15 Saturday, September 7, 2002 12:58 PM
Page 235 of 289
8-16
Maintenance and Care
Owner Maintenance
Form No. 8R29-EA-02I
Adding Brake/Clutch Fluid
If the fluid level is low, add fluid until it
reaches MAX.
Before adding fluid, thoroughly clean the
area around the cap.
Spilled Brake Fluid:Spilled brake fluid is dangerous. If it
gets in your eyes, they could be
seriously injured. If this happens,
immediately flush your eyes with
water and get medical attention.
Brake fluid spilled on a hot engine
could cause a fire. Be careful not to
spill brake fluid on yourselfor on the
engine.
Low Brake/Clutch Fluid Levels:
Low brake/clutch fluid levels are
dangerous. Low levels could signal
brake lining wear or a brake system
leak. Your brakes could fail and cause
an accident. If you find a low fluid
level, have the brakes and clutch
inspected.
WARNING•
Brake and clutch fluid will damage
painted surfaces. If brake or clutch
fluid does get on a painted surface,
wipe it off immediately.
•
Using nonspecified brake and clutch
fluids (page 10-3) will damage the
systems. Mixing different fluids
will also damage them.
If the brake/clutch system
frequently requires new fluid,
consult an Authorized Mazda
Dealer.
CAUTION
shuseizumi_J56J_8R29_EA_02I.book Page 16 Saturday, September 7, 2002 12:58 PM
Page 262 of 289
8-43
Maintenance and Care
Appearance Care
Form No. 8R29-EA-02I
Pay special attention to removing salt,
dirt, mud, and other foreign material from
the underside of the fenders, and make
sure the drain holes in the lower edges of
the doors and rocker panels are clean.
Insects, tar, tree sap, bird droppings,
industrial fallout, and similar deposits can
damage the finish if not removed
immediately. When prompt washing with
plain water is ineffective, use a mild soap
made for use on vehicles.
Thoroughly rinse off all soap with
lukewarm or cold water. Don’t allow soap
to dry on the finish.
After washing the vehicle, dry it with a
clean chamois to prevent water spots from
forming.Wa x i n g
Your vehicle needs to be waxed when
water no longer beads on the finish.
Always wash and dry the vehicle before
waxing it. In addition to the vehicle body,
wax the metal trim to maintain its luster.
1. Use wax which contains no abrasives.
Waxes containing abrasive will remove
paint and could damage bright metal
parts.
2. Use a good grade of natural wax for
metallic, mica, and solid colors.
3. When waxing, coat evenly with the
sponge supplied or a soft cloth.
4. Wipe off the wax with a soft cloth.
Driving with Wet Brakes:Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected. Dry the brakes by driving
very slowly and applying the brakes
lightly until brake performance is
normal.
WARNING
NOTE
A spot remover to remove oil, tar, and
similar materials will usually also take
off the wax. Rewax these areas even if
the rest of the vehicle doesn’t need it.
shuseizumi_J56J_8R29_EA_02I.book Page 43 Saturday, September 7, 2002 12:58 PM