ECU MAZDA MODEL 6 2008 (in English) Owner's Manual
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2008, Model line: MODEL 6, Model: MAZDA MODEL 6 2008Pages: 440, PDF Size: 6.49 MB
Page 90 of 440

Black plate (90,1)
NOTEIf the vehicle battery is dead or there is a
malfunction in the electrical system and the
liftgate cannot be unlocked, perform the
following procedure as an emergency measure
to unlock it:
1. Remove the cap on the interior surface ofthe liftgate with a flathead screwdriver.
Cap
2. Turn the lever to the right to unlock theliftgate.
Lever
After performing this emergency measure,
have the vehicle inspected at an Authorized
Mazda Dealer as soon as possible.
Closing the liftgate
Use both hands to push the liftgate down
until the lock snaps shut. Do not slam it.
Pull up on the liftgate to make sure it is
securely latched.
qLuggage Compartment Cover
Use the luggage compartment cover to
conceal cargo or luggage.
WARNING
Do not place anything on top of the
luggage compartment cover:
Placing luggage or other cargo on
top of the luggage compartment
cover is dangerous. During sudden
braking or a collision, the cargo
could become a projectile that could
hit and injure someone.
CAUTION
Make sure the luggage compartment
cover is firmly secured. If it is not
firmly secured, it could unexpectedly
disengage resulting in injury.
Installing the cover
1. Set the left end of the retainer bar intothe notch on the left side of the luggage
compartment.
Retainer bar
Notch
3-14
Knowing Your Mazda
Doors and Locks
Mazda6_8X47-EA-07G_Edition1 Page90
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G
Page 91 of 440

Black plate (91,1)
2. Set the right side of the retainer baronto the retainer loop on the right side
of the luggage compartment.
Retainer
loop
3. Slowly pull out the cover towards youand insert the cover ends into the hook
retainers at the rear of the vehicle.
Hook
retainer
Removing the cover
1. Remove the cover ends from the hookretainers and slowly roll up the cover. NOTE
To fully retract and protect the cover, guide the
cover all the way into the retainer.
Ta b
2. Press and hold the button on the right
side of the retainer bar and lift the bar.
Button
3. Remove the left end of the retainer barfrom the notch.
qLuggage Compartment Net
The luggage compartment net can be used
as a compartment separator or to keep
animals in the back.
CAUTION
Make sure the net is firmly secured. If
it is not firmly secured, it could
unexpectedly disengage resulting in
injury.
Knowing Your Mazda
Doors and Locks
3-15
Mazda6_8X47-EA-07G_Edition1 Page91
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G
Page 92 of 440

Black plate (92,1)
NOTEThe width of the net anchors can be shortened
by pushing both sides inward.
Net anchor
Dividing the luggage compartmentfrom the rear seat
WARNING
Do not use the luggage compartment
net to secure objects in the luggage
compartment or the rear seat area:Using the luggage compartment net
to secure objects in the luggage
compartment or the rear seat area is
dangerous. The luggage
compartment net is not designed to
hold objects in place that could fly
forward in a frontal collision.
Unsecured objects that are thrown
around the inside of the vehicle could
cause injury to occupants. This is
particularly true for objects stacked
above the seatback level. Never stack
objects above the seatback level. If
the luggage compartment is divided
from the rear seat, pull the luggage
compartment cover over the cargo in
the luggage compartment.
Make sure luggage and cargo is
secured before driving: Not securing cargo while driving is
dangerous as it could move or be
crushed during sudden braking or a
collision and cause injury.
To install the net:
1. Install the retainer bar in the luggage compartment.
3-16
Knowing Your Mazda
Doors and Locks
Mazda6_8X47-EA-07G_Edition1 Page92
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G
Page 93 of 440

Black plate (93,1)
2. Slowly pull out the net in the upwarddirection, insert the left and right net
anchors into the ceiling retainers, and
slide them to the position indicated in
the figure.
Net
anchor
Net
To remove the net:
1. Lift the net slightly and disengage the
anchors from the ceiling retainers.
2. Slowly lower and support the net as it rolls up into the retainer bar.
CAUTION
When disengaging the net anchors,
hold the top of the net firmly in your
hand. If you lose control of the net, it
will automatically roll up in an
uncontrolled manner and could
cause injury.
Dividing the luggage compartmentfrom the front seats
WARNING
Do not use the luggage compartment
net to secure objects in the luggage
compartment or the rear seat area: Using the luggage compartment net
to secure objects in the luggage
compartment or the rear seat area is
dangerous. The luggage
compartment net is not designed to
hold objects in place that could fly
forward in a frontal collision.
Unsecured objects that are thrown
around the inside of the vehicle could
cause injury to occupants. This is
particularly true for objects stacked
above the seatback level. Never stack
objects above the seatback level. If
the luggage compartment is divided
from the rear seat, pull the luggage
compartment cover over the cargo in
the luggage compartment.
Make sure luggage and cargo is
secured before driving: Not securing cargo while driving is
dangerous as it could move or be
crushed during sudden braking or a
collision and cause injury.
CAUTION
Moving the rear seatbacks with the
retainer bar mounted could scratch
the interior of the vehicle. The
retainer bar must be removed from
the back of the seatbacks before
raising the seatbacks.
To install the net:
1. Fold down the rear seatback (page 2-11).
Knowing Your Mazda
Doors and Locks
3-17
Mazda6_8X47-EA-07G_Edition1 Page93
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G
Page 96 of 440

Black plate (96,1)
Opening the trunk lid with the key
Insert the key into the slot and turn it
clockwise.
Open
Opening the trunk lid with thetransmitter
The trunk lid can be opened by operating
the keyless entry system transmitter, refer
to Keyless Entry System (page 3-3).
Opening the trunk lid with the remoterelease button
Push the release button.
Closing the trunk lid
Use both hands to push the trunk lid down
until the lock snaps shut. Do not slam it.
Pull up on the trunk lid to make sure it is
secure.
qTrunk Light
The trunk light is on when the lid is open
and off when it's closed.
NOTETo prevent the battery from being discharged,
do not leave the trunk open for a long period
when the engine is not running.
3-20
Knowing Your Mazda
Doors and Locks
Mazda6_8X47-EA-07G_Edition1 Page96
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G
Page 103 of 440

Black plate (103,1)
NOTEWhen the power window lock switch is in the
locked position, the light on front passenger's
power window switch turns off. The light may
be difficult to see depending on the
surrounding brightness.
qOpening/Closing the Power
Windows from Outside
The front power windows can be opened
or closed from outside the vehicle after
the doors and the hatch/liftgate/trunk lid
are closed.
The front power windows may be
operated when the power window lock
switch on the driver's door is in the lock
or unlocked position.
WARNING
Make sure the opening is clear before
closing a window:
Closing power windows are
dangerous. A person's hands, head,
or even neck could be caught by the
window and result in serious injury
or even death.
This warning applies especially to
children.
NOTE
The power windows cannot be opened or
closed from outside the vehicle under the
following condition:
lA door or the hatch/liftgate/trunk lid is
opened.
lThe key is inserted into the ignition switch.
Opening
Because nobody likes getting into a very
hot car, Mazda has introduced a way to
open the two front windows as you
approach the vehicle to get the air moving
before you get in.
WARNING
Use the auto-window function only
when you can see the vehicle and it is
in a secure area: Do not let children play with your
keys. If they open the window
without your knowing, the open
windows are an even bigger
invitation to a thief than leaving the
doors unlocked.
The windows can be opened for
ventilating the cabin before getting in the
vehicle.
With unlock button (Keyless entry
system)
Press once, then press again within 1.5
seconds and hold.
After the doors and the hatch/liftgate/
trunk lid are unlocked, the two front
windows open while the unlock button is
pressed.
To stop the windows while opening,
release the button.
If the operation is performed from the
beginning again, the windows open.
Sedan
Lock button Unlock button
Trunk button Panic button
Knowing Your Mazda
Doors and Locks
3-27
Mazda6_8X47-EA-07G_Edition1 Page103
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G
Page 106 of 440

Black plate (106,1)
CAUTION
Make sure the fuel-filler cap is
tightened securely. The check engine
light may illuminate when the cap
isn't tightened securely. If the light
remains on (even after you have
tightened the cap securely, driven,
and restarted the engine several
times), it may indicate a different
problem. Contact an Authorized
Mazda Dealer as soon as possible.
Hood
WARNING
Always check that the hood is closed
and securely locked:A hood that is not closed and
securely locked is dangerous as it
could fly open while the vehicle is
moving and block the driver's vision
which could result in a serious
accident.
qOpening the Hood
1. With the vehicle parked, pull the
release handle to unlock the hood.
2. Insert your hand into the hood opening
and slide the hood latch lever to the
right and lift the hood.
3-30
Knowing Your Mazda
Doors and Locks
Mazda6_8X47-EA-07G_Edition1 Page106
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G
Page 107 of 440

Black plate (107,1)
3. Grasp the support rod and secure it inthe stay hole indicated by the arrow to
hold the hood open.
Clip
Support rod
q
Closing the Hood
1. Check under the hood area to make
certain all filler caps are in place and
all loose items (e.g. tools, oil
containers, etc.) have been removed.
2. Insert the support rod in its clip while holding up the hood. Verify that the
support rod is secured in the clip before
closing the hood.
3. Close the hood so that it locks securely.
Moonroofí
The moonroof can be opened or closed
electrically only when the ignition switch
is in the ON position.
Tilt switch
Slide switch
WARNING
Do not let passengers stand up or
extend part of the body through the
open moonroof while the vehicle is
moving:
Extending the head, arms, or other
parts of the body through the
moonroof is dangerous. The head or
arms could hit something while the
vehicle is moving. This could cause
serious injury or death.
Make sure the opening is clear before
closing the moonroof: A closing moonroof is dangerous. The
hands, head, or even neck of a
person ―especially a child ―could
be caught in it as it closes, causing
serious injury or even death.
NOTE
After washing your Mazda or after it rains,
wipe the water off the moonroof before
operating it to avoid water penetration which
could cause rust and water damage to your
headliner.
Knowing Your Mazda
Doors and Locks
3-31íSome models.
Mazda6_8X47-EA-07G_Edition1 Page107
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G
Page 109 of 440

Black plate (109,1)
Immobilizer System
The immobilizer system allows the engine
to start only with a key the system
recognizes.
If someone attempts to start the engine
with an unrecognized key, the engine will
not start, thereby helping to prevent the
theft of your vehicle.
CAUTION
ØRadio equipment like this is
governed by laws in the United
States.
Changes or modifications not
expressly approved by the party
responsible for compliance could
void the user's authority to
operate the equipment.
Ø To avoid damage to the key, do
not:
ØDrop the key.ØGet the key wet.ØExpose the key to any kind of
magnetic field.
ØExpose the key to high
temperatures on places such as
the dashboard or hood, under
direct sunlight.
CAUTION
When starting the engine do not
allow the following, as the engine
may not start due to the electronic
signal from the ignition key not being
transmitted correctly.
ØA key ring rests on the key grip.
ØMetal parts of other keys or metal
objects touch the key grip.
ØSpare keys or keys for other
vehicles equipped with an
immobilizer system touch or come
near the key grip.
ØDevices for electronic purchases, or
security passage touch or come
near the key.
Knowing Your Mazda
Security System
3-33
Mazda6_8X47-EA-07G_Edition1 Page109
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G
Page 110 of 440

Black plate (110,1)
NOTEl(U.S.A.)
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference, and (2)
this device must accept any interference
received, including interference that may
cause undesired operation.
l(CANADA)
This device complies with RSS-210 of
Industry CANADA. Operation is subject to
the following two conditions: (1) this device
may not cause interference, and (2) this
device must accept any interference,
including interference that may cause
undesired operation of the device.
qOperation
Arming
The system is armed when the ignition
switch is turned from the ON to the ACC
position.
The security indicator light in the
instrument panel flashes every 2 seconds
until the system is disarmed.
Disarming
The system is disarmed when the ignition
switch is turned to the ON position with
the correct ignition key.
The security indicator light illuminates for
about 3 seconds and goes out. If the engine doesn't start with the correct
ignition key, and the security indicator
light keeps illuminating or flashing, the
system may have a malfunction. Consult
an Authorized Mazda Dealer.
NOTE
lIf the security indicator light comes on and
stays on when the ignition switch is turned
to the ON position, the engine will not start.
lSignals from a TV or radio station, or from
a transceiver or a mobile telephone, could
interfere with your immobilizer system. If
you are using the proper key and your
engine fails to start, check the security
indicator light. If it is flashing, remove the
ignition key and wait 2 seconds or more,
then reinsert it and try starting the engine
again. If it doesn't start after 3 or more
tries, contact an Authorized Mazda Dealer.
lIf the security indicator light flashes
continuously while you are driving, don't
shut off the engine. Go to an Authorized
Mazda Dealer and have it checked. If you
shut off the engine while the light is
flashing you won't be able to restart it.
lSince the electronic codes are reset when
repairing the immobilizer system, the keys
are needed. Bring all the existing keys to an
Authorized Mazda Dealer.
3-34
Knowing Your Mazda
Security System
Mazda6_8X47-EA-07G_Edition1 Page110
Tuesday, May 29 2007 3:43 PM
Form No.8X47-EA-07G