warning MAZDA MODEL 626 2002 Owners Manual

8-39
Maintenance and Care
Owner Maintenance
Form No. 8Q50-EA-01G
Fuse panel (Driver’s side)
DESCRIPTION FUSE
RATING PROTECTED
COMPONENT
1 AUDIO 15A Audio system
2 ROOM 15A Interior lights,
Trunk light
3 S.ROOF 15A Sunroof
4 METER 10A Gauges, Reverse
lights
5 D.LOCK 30A Power door lock
6 HAZARD 15A Hazard warning
lights
7A/B&ABS 10A Air bag system,
Antilock brake system
8 —— —
9 A/C 10A Air conditioner
10 —— —
11 TURN 10A Turn signals
12 WIPER 20A Windshield
wipers and washer
13 P.WIND 30A Power windows
14 —— —DESCRIPTION FUSE
RATING PROTECTED
COMPONENT
15 RADIO 15A Audio system,
Socket, Outside mirror
16 ENGINE 10A Engine control
system
17 ILLUMI 10A Taillights,
License plate
lights, Parking
lights, Dashboard illumination
18 STOP 15A Brake lights,
Horn, Cruise control
19 CIGAR 15A Accessory
socket, Clock,
Radio, Outside mirror
20 —— —
21 —— —
22 P.SEAT 30A Power seat
23 M.DEF 15A Mirror defroster
24 P.POINT 15A Power point
J94S.book Page 39 Saturday, June 23, 2001 1:04 PM

8-42
Maintenance and Care
Appearance Care
Form No. 8Q50-EA-01G
Follow all label and container directions
when using a chemical cleaner or polish.
Read all warnings and cautions.





Maintaining the Finish
Was hi n g
To help protect the finish from rust and
deterioration, wash your Mazda
thoroughly and frequently, at least once a
month, with lukewarm or cold water.
If the vehicle is washed improperly, the
paint surface could be scratched. Here are
some examples of how scratching could
occur.
Scratches occur on the paint surface
when:
• The vehicle is washed without first
rinsing off dirt and other foreign
matter.
• The vehicle is washed with a rough,
dry, or dirty cloth.
• The vehicle is washed at a car wash
that uses brushes that are dirty or too
stiff.
• Cleansers or wax containing abrasives
are used. To minimize scratches on the vehicle
’s
paint finish:
• Rinse off any dirt or other foreign
matter using lukewarm or cold water
before washing.
• Use plenty of lukewarm or cold water
and a soft cloth when washing the
vehicle. Do not use a nylon cloth.
• Rub gently when washing or drying the
vehicle.
• Take your vehicle only to a car wash
that keeps its brushes well maintained.
• Don ’t use abrasive cleansers or wax
that contain abrasives.
Pay special attention to removing salt,
dirt, mud, and other foreign material from
the underside of the wings, and make sure
the drain holes in the lower edges of the
doors and rocker panels are clean.
Exterior Care
NOTE
• Mazda is not responsible for
scratches caused by automatic car
washes or improper washing.
• Scratches are more noticeable on
vehicles with darker paint finishes.
•Don ’t use steel wool, abrasive
cleaners, or strong detergents
containing highly alkaline or caustic
agents on chrome-plated or
anodized aluminum parts. This may
damage the protective coating; also,
cleaners and detergents may
discolor or deteriorate the paint.
• To prevent damaging the antenna,
retract it before entering a car wash
facility or passing beneath a low
overhead clearance.
CAUTION
J94S.book Page 42 Saturday, June 23, 2001 1:04 PM

8-43
Maintenance and Care
Appearance Care
Form No. 8Q50-EA-01G
Insects, tar, tree sap, bird droppings,
industrial fallout, and similar deposits can
damage the finish if not removed
immediately. When prompt washing with
plain water is ineffective, use a mild soap
made for use on vehicles.
Thoroughly rinse off all soap with
lukewarm or cold water. Don’t allow soap
to dry on the finish.
After washing the vehicle, dry it with a
clean chamois to prevent water spots from
forming.
Waxing
Your vehicle needs to be waxed when
water no longer beads on the finish.
Always wash and dry the vehicle before
waxing it. In addition to the vehicle body,
wax the metal trim to maintain its luster.
1. Use wax which contains no abrasives. Waxes containing abrasive will remove
paint and could damage bright metal
parts.
2. Use a good grade of natural wax for metallic, mica, and solid colors. 3. When waxing, coat evenly with the
sponge supplied or a soft cloth.
4. Wipe off the wax with a soft cloth.





Repairing Damage to the Finish
Deep scratches or chips on the finish
should be repaired promptly. Exposed
metal quickly rusts and can lead to major
repairs.





Bright-Metal Maintenance
• Use tar remover to remove road tar and
insects. Never do this with a knife or
similar tool.
• To prevent corrosion on bright-metal
surfaces, apply wax or chrome
preservative and rub it to a high luster.
• During cold weather or in coastal
areas, cover bright-metal parts with a
coating of wax or preservative heavier
than usual. It would also help to coat
them with noncorrosive petroleum jelly
or some other protective compound.
Driving with Wet Brakes:Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected. Dry the brakes by driving
very slowly and applying the brakes
lightly until brake performance is
normal.
WARNING
NOTE
A spot remover to remove oil, tar, and
similar materials will usually also take
off the wax. Rewax these areas even if
the rest of the vehicle doesn ’t need it.
If your Mazda is damaged and needs
metal parts repaired or replaced, make
sure the body shop applies anti-
corrosion materials to all parts, both
repaired and new. This will prevent
them from rusting.
CAUTION
J94S.book Page 43 Saturday, June 23, 2001 1:04 PM

8-44
Maintenance and Care
Appearance Care
Form No. 8Q50-EA-01G





Underbody Maintenance
Road chemicals and salt used for ice and
snow removal and solvents used for dust
control may collect on the underbody. If
not removed, they will speed up rusting
and deterioration of such underbody parts
as fuel lines, frame, floor pan, and exhaust
system, even though these parts may be
coated with anti-corrosive material.
Thoroughly flush the underbody and
wheel housings with lukewarm or cold
water at the end of each winter. Try also to
do this every month.
Pay special attention to these areas
because they easily hide mud and dirt. It
will do more harm than good to wet
down the road grime without removing
it.
The lower edges of doors, rocker panels,
and frame members have drain holes that
should not be clogged. Water trapped
there will cause rusting.





Aluminum Wheel Maintenance
A protective coating is provided over the
aluminum wheels. Special care is needed
to protect this coating.
Don
’t use steel wool, abrasive
cleaners, or strong detergents
containing highly alkaline or caustic
agents on chrome-plated or anodized
aluminum parts. This may result in
damage to the protective coating and
cause discoloration or paint
deterioration.
CAUTION
Driving with Wet Brakes:Driving with wet brakes is dangerous.
Increased stopping distance or the
vehicle pulling to one side when
braking could result in a serious
accident. Light braking will indicate
whether the brakes have been
affected. Dry the brakes by driving
very slowly and applying the brakes
lightly until brake performance is
normal.
NOTE
• Don ’t use a wire brush or any
abrasive cleaner, polishing
compound, or solvent on aluminum
wheels. They may damage the
coating.
• Only use a mild soap or neutral
detergent and always use a sponge
or soft cloth to clean the wheels.
Rinse thoroughly with lukewarm or
cold water. Also, be sure to clean
the wheels after driving on dusty or
salted roads. This helps prevent
corrosion.
• Avoid washing your vehicle in an
automatic car wash that uses high-
speed or hard brushes.
• If your aluminum wheels lose
luster, wax the wheels.
WARNING
J94S.book Page 44 Saturday, June 23, 2001 1:04 PM

8-45
Maintenance and Care
Appearance Care
Form No. 8Q50-EA-01G





Dashboard Precautions
Prevent caustic solutions such as perfume
and cosmetic oils from contacting the
dashboard. They ’ll damage and discolor
it. If these solutions get on the dashboard,
wipe them off immediately.





Cleaning the Upholstery and
Interior Trim
Vinyl
Remove dust and loose dirt from vinyl
with a whisk broom or vacuum cleaner.
Clean vinyl with a leather-and-vinyl
cleaner.
Leather
Real leather isn ’t uniform and may have
scars, scratches, and wrinkles. Clean it
with a leather cleaner or mild soap.
Wipe it with a damp soft cloth; then dry
and buff it with a dry soft cloth.
Fabric
Remove dust and loose dirt from fabric
with a whisk broom or vacuum cleaner.
Clean it with a mild soap solution good
for upholstery and carpets. Remove fresh
spots immediately with a fabric spot
cleaner.
To keep the fabric looking clean and
fresh, take care of it. Otherwise its color
will be affected, it can be stained easily,
and its fire-resistance may be reduced.





Cleaning the Lap/Shoulder Belt
We b b i n g
Clean the webbing with a mild soap
solution recommended for upholstery or
carpets. Follow instructions. Don ’t bleach
or dye the webbing; this may weaken it.
After cleaning the belts, thoroughly dry
the belt webbing and make sure there is
no remaining moisture before retracting
them.





Cleaning the Window Interiors
If the windows become covered with an
oily, greasy, or waxy film, clean them
with glass cleaner. Follow the directions
on the container.
Interior Care
Use only recommended cleaners and
procedures. Others may affect
appearance and fire-resistance.
Damaged Seat Belt:Using damaged seat belts is
dangerous. In a collision, damaged
belts cannot provide adequate
protection. Have your Authorized
Mazda Dealer replace damaged belts
immediately.
Don ’t scrape or scratch the inside of
the rear window. You may damage the
rear window defroster grid.
CAUTION
WARNING
CAUTION
J94S.book Page 45 Saturday, June 23, 2001 1:04 PM

9-10
Customer Information
Warranty
Form No. 8Q50-EA-01G
Non-genuine parts and accessories for Mazda vehicles can be found in stores.
These may fit your vehicle, but they are not approved by the Mazda for use with Mazda
vehicles. When you install non-genuine parts or accessories, they could affect your
vehicle’s performance or safety system; the Mazda warranty doesn ’t cover this. Before you
install any non-genuine parts or accessories, consult an Authorized Mazda Dealer.
Mazda assumes no responsibility for death, injury, or expenses that may result from the
installation of add-on non-genuine parts or accessories.
Add-On Non-Genuine Parts and Accessories
Installation of Non-Genuine Parts or Accessories:Installation of non-genuine parts or accessories is dangerous. Improperly designed
parts or accessories could seriously affect your vehicle ’s performance or safety
system. This could cause you to have an accident or increase your chances of injuries
in an accident. Always consult an Authorized Mazda Dealer before you install non-
genuine parts or accessories.
Add-On Electrical and Electronic Equipment:
Incorrectly choosing or installing improper add-on equipment or choosing an
improper installer is dangerous. Essential systems could damaged, causing engine
stalling, air-bag (SRS) activation, ABS inactivation, or a fire in the vehicle.
Be very careful in choosing and installing add-on electrical equipment, such as
mobile telephones, two-way radios, stereo systems, and car alarm systems.
WARNING
J94S.book Page 10 Saturday, June 23, 2001 1:04 PM

9-11
Customer Information
Wa r r a n t y
Form No. 8Q50-EA-01G
Cell Phones
Use of Cell Phones and Other Devices by Driver:Although not Mazda products, use of any electrical devices such as cell phones,
computers, portable radios, vehicle navigation or other devices by the driver while the
vehicle is moving is dangerous. Dialing a number on a cell phone while driving also
ties-up the driver's hands. Use of these devices will cause the driver to be distracted
and could lead to a serious accident. If a passenger is unable to use the device, pull off
the right-of-way to a safe area before use. If use of a cell phone is necessary despite
this warning, use a hands-free system to at least leave the hands free to drive the
vehicle. Never use a cell phone or other electrical device while the vehicle is moving
and, instead, concentrate on the full-time job of driving.
WARNING
J94S.book Page 11 Saturday, June 23, 2001 1:04 PM

9-12
Customer Information
Form No. 8Q50-EA-01G
Uniform Tire Quality Grading System (UTQGS)
This information relates to the tire grading system developed by the U.S. National
Highway Traffic Safety Administration for grading tires by tread wear, traction, and
temperature performance.





Tre a d We a r
The tread wear grade is a comparative rating based on the wear rate of the tire when tested
under controlled conditions on a specified government test course.
For example, a tire graded 150 would wear one-and-a-half times as well on the government
course as a tire graded 100.
The relative performance of tires depends upon the actual conditions of their use, however,
and may depart significantly from the norm because of variations in driving habits, service
practices and differences in road characteristics and climate.





Traction-AA, A, B, C
The traction grades, from highest to lowest, are AA, A, B, and C. These grades represent
the tire ’s ability to stop on wet pavement as measured under controlled conditions on
specified government test surfaces of asphalt and concrete. A tire marked C may have poor
traction performance.





Temperature-A, B, C
The temperature grades are A (the highest), B, and C, represent the tire ’s resistance to the
generation of heat and its ability to dissipate heat when tested under controlled conditions
on a specified indoor laboratory test wheel.
Sustained high temperature can cause the material of the tire to degenerate and reduce tire
life, and excessive temperatures can lead to sudden tire failure.
Grade C corresponds to a level of performance which all passenger vehicle tires must meet
under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A represent
higher levels of performance on the laboratory test wheel than the minimum required by
law.
Uniform Tire Quality Grading System (UTQGS)
The traction grade assigned to this tire is based on braking (straight ahead) traction
tests and does not include acceleration cornering (turning), hydroplaning, or peak
traction characteristics.
WARNING
J94S.book Page 12 Saturday, June 23, 2001 1:04 PM

9-13
Customer Information
Uniform Tire Quality Grading System (UTQGS)
Form No. 8Q50-EA-01G
These grades will be added to the sidewalls of passenger vehicle tires over the next several
years according to a schedule established by the NHTSA and the tire manufacturers.
The grade of tires available as standard or optional equipment on Mazda vehicle may vary
with respect to grade.
ALL PASSENGER VEHICLE TIRES MUST CONFORM TO THESE GRADES AND
TO ALL OTHER FEDERAL TIRE-SAFETY REQUIREMENTS.





Uniform Tire Quality Grading
Quality grades can be found where applicable on the tire sidewall between tread shoulder
and maximum section width.
For example:
Treadwear 200 Traction AA Temperature A
The temperature grade for this tire is established for a tire that is properly inflated
and not overloaded. Excessive speed, underinflation, or excessive loading, either
separately or in combination, can cause heat buildup and possible tire failure.
WARNING
UTQGS MARK (example)
TREADWEAR 200 TRACTION AA
TEMPERATURE A
J94S.book Page 13 Saturday, June 23, 2001 1:04 PM

11-2
Form No. 8Q50-EA-01G
Index
A
Accessory Socket ............................. 6-38
Add-On Non-Genuine Parts and
Accessories
...................................... 9-10
Air Bag Systems
.............................. 2-25
Air Filter
.......................................... 8-21
Antenna
............................................ 6-11
Anti-Lock Brake System (ABS)
........ 5-6
Warning light
.............................. 5-7
Appearance Care
.............................. 8-40
Audio System
................................... 6-11
Audio set
................................... 6-19
Operating tips for
audio system
............................. 6-11
Safety certification
.................... 6-36
Automatic Transaxle Driving tips
............................... 5-12
Fluid
.......................................... 8-18
Overdrive
.................................. 5-11
Shift-lock system
...................... 5-10
Transaxle ranges
......................... 5-9
B
Battery Emergency starting
................... 7-12
Maintenance
............................. 8-24
Specifications
........................... 10-4
Beeps Ignition key reminder
............... 5-31
Lights-on reminder
................... 5-31
Before Starting the Engine
................. 4-6
After getting in
........................... 4-6
Before getting in
......................... 4-6
Body Lubrication
............................. 8-21
Brake/Clutch Fluid
.......................................... 8-15
B
BrakesAnti-lock brake system (ABS)
.... 5-6
Foot brake
................................... 5-4
Pad wear indicator
...................... 5-7
Parking brake
.............................. 5-5
Warning light
.............................. 5-5
Break-In Period
.................................. 4-7
Bulb Replacement
............................ 8-29
C
Capacities ......................................... 10-5
Carbon Monoxide
.............................. 4-5
Catalytic Converter
............................ 4-4
Cell Phones
...................................... 9-11
Center Console
................................. 6-43
Center Pocket
................................... 6-42
Child Restraint Child restraint precautions
........ 2-18
Installing child-restraint
systems
...................................... 2-21
Child Safety Lock for Rear Door
....... 3-5
Climate Control System
..................... 6-2
Gas specifications
..................... 10-6
Courtesy Light
.................................. 6-38
Cruise Control
.................................. 5-13
Cup Holders
..................................... 6-40
Customer Assistance
.......................... 9-2
D
Dashboard Illumination .................... 5-22
Daytime Running Lights
.................. 5-33
Defroster Rear window
............................. 5-35
Dimensions
....................................... 10-5
Door Locks
......................................... 3-3
Driving In Flooded Area
.................. 4-10
J94S.book Page 2 Saturday, June 23, 2001 1:04 PM