oil level MAZDA MODEL CX-3 2015 Owners Manual (in English)
[x] Cancel search | Manufacturer: MAZDA, Model Year: 2015, Model line: MODEL CX-3, Model: MAZDA MODEL CX-3 2015Pages: 671, PDF Size: 7.03 MB
Page 182 of 671
*Some models.4–42
When Driving
Instrument Cluster and Display
Wrench Indicator Light
When the ignition is switched ON, the
wrench indicator light is illuminated and
then turns off after a few seconds.
The wrench indicator light is illuminated
when the preset maintenance period
arrives. Verify the content and perform
maintenance.
Refer to Maintenance Monitor on page
6-15 .
SKYACTIV-D 1.5
The wrench indicator light turns on
when the engine oil has deteriorated, is
insuffi cient
* , is around the X mark on
the oil level gauge or reaches a position
exceeding the X mark.
Check the engine oil. Refer to Inspecting
Engine Oil Level on page 6-28 .
Replace the engine oil if the wrench
indicator light does not turn off even
though the engine oil level is in the normal
range.
NOTE
Depending on the vehicle use
conditions, the wrench indicator light
may turn on for reasons other than
the preset maintenance period.
Whenever the engine oil is replaced,
a reset of the vehicle engine control
unit necessary.
Your Authorised Mazda Repairer will
be able to reset the engine control
unit or see page 6-27 for the Vehicle
engine control unit reset procedure.
Low Engine Coolant Temperature
Indicator Light (Blue)
The light illuminates continuously when
the engine coolant temperature is low and
turns off after the engine is warm.
If the low engine coolant temperature
indicator light remains illuminated after
the engine has been suffi ciently warmed
up, the temperature sensor could have a
malfunction. Consult an expert repairer,
we recommend an Authorised Mazda
Repairer.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 484 of 671
6–6
Maintenance and Care
Scheduled Maintenance
*6 If the vehicle is operated primarily under any of the following conditions, replace the engine oil and oil fi lter at
every 10,000 km (6,250 miles) or shorter.
a) Purpose of vehicle use is police car, taxi or driving school car.
b) Driving in dusty conditions
c) Extended periods of idling or low speed operation
d) Driving for long period in cold temperatures or driving regularly at short distance only
e) Driving in extremely hot conditions
f) Driving in mountainous conditions continually
*7 For SKYACTIV-D 1.5, reset the engine oil data after replacing the engine oil.
*8 Use of FL-22 is recommended when replacing engine coolant. Using engine coolant other than FL-22 may
cause serious damage to the engine and cooling system.
*9 Inspect the battery electrolyte level, specifi c gravity and outer appearance. The sealed battery only requires an
outer appearance inspection.
*10 If the brakes are used extensively (for example, continuous hard driving or mountain driving) or if the vehicle
is operated in extremely humid climates, replace the brake fl uid annually.
*11 If the vehicle is operated primarily under any of the following conditions, replace the rear differential oil at
every 45,000 km (27,000 miles).
a) Towing a trailer or using a car-top carrier
b) Driving in dusty, sandy or wet condition
c) Extended periods of idling or low speed operation
d) Repeated short trips of less than 16 km (10 miles)
*12 If this component has been submerged in water, the oil should be replaced.
*13 Tyre rotation is recommended every 10,000 km (6,250 miles).
*14 The Tyre Pressure Monitoring System (TPMS) initialization must be performed so that the system operates
normally (if equipped).
*15 Check the tyre repair fl uid expiration date every year when performing the periodic maintenance. Replace the
tyre repair fl uid bottle with new one before the expiration date.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 486 of 671
6–8
Maintenance and Care
Scheduled Maintenance
Chart symbols:
I: Inspect: Inspect and clean, repair, adjust, fi ll up, or replace if necessary.
R: Replace
C: Clean
T: Tighten
Remarks:
*1 Also inspect the air conditioner drive belts, if installed.
If the vehicle is operated primarily under any of the following conditions, inspect the drive belts at every 10,000
km or shorter.
a) Driving in dusty conditions
b) Extended periods of idling or low speed operation
c) Driving for long period in cold temperatures or driving regularly at short distance only
d) Driving in extremely hot conditions
e) Driving in mountainous conditions continually
*2 If the vehicle is operated primarily under any of the following conditions, replace the engine oil and oil fi lter at
every 10,000 km or shorter.
a) Driving in dusty conditions
b) Extended periods of idling or low speed operation
c) Driving for long period in cold temperatures or driving regularly at short distance only
d) Driving in extremely hot conditions
e) Driving in mountainous conditions continually
*3 If the vehicle is operated in very dusty or sandy areas, clean and if necessary, replace the air fi lter more often
than the recommended intervals.
*4 Use of FL-22 is recommended when replacing engine coolant. Using engine coolant other than FL-22 may
cause serious damage to the engine and cooling system.
*5 Inspect the battery electrolyte level, specifi c gravity and outer appearance. The sealed battery only requires an
outer appearance inspection.
*6 If the brakes are used extensively (for example, continuous hard driving or mountain driving) or if the vehicle is
operated in extremely humid climates, replace the brake fl uid annually.
*7 If the vehicle is operated primarily under any of the following conditions, replace the rear differential oil at
every 45,000 km.
a) Towing a trailer or using a car-top carrier
b) Driving in dusty, sandy or wet condition
c) Extended periods of idling or low speed operation
d) Repeated short trips of less than 16 km
*8 If this component has been submerged in water, the oil should be replaced.
*9 The Tyre Pressure Monitoring System (TPMS) initialization must be performed so that the system operates
normally (if equipped).
*10 Check the tyre repair fl uid expiration date every year when performing the periodic maintenance. Replace the
tyre repair fl uid bottle with new one before the expiration date.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 489 of 671
6–11
Maintenance and Care
Scheduled Maintenance
*4 If the vehicle is operated primarily under any of the following conditions, replace the engine oil fi lter at every
5,000 km or 6 months.
a) Purpose of vehicle use is police car, taxi or driving school car.
b) Driving in dusty conditions
c) Extended periods of idling or low speed operation
d) Driving for long period in cold temperatures or driving regularly at short distance only
e) Driving in extremely hot conditions
f) Driving in mountainous conditions continually
*5 Use of FL-22 is recommended when replacing engine coolant. Using engine coolant other than FL-22 may
cause serious damage to the engine and cooling system.
*6 If the vehicle is operated in very dusty or sandy areas, clean the air fi lter at every 7,500 km or 6 months.
*7 Inspect the battery electrolyte level, specifi c gravity and outer appearance. The sealed battery only requires an
outer appearance inspection.
*8 If the brakes are used extensively (for example, continuous hard driving or mountain driving) or if the vehicle is
operated in extremely humid climates, replace the brake fl uid annually.
*9 If the vehicle is operated primarily under any of the following conditions, replace the rear differential oil at
every 45,000 km.
a) Towing a trailer or using a car-top carrier
b) Driving in dusty, sandy or wet condition
c) Extended periods of idling or low speed operation
d) Repeated short trips of less than 16 km
*10 If this component has been submerged in water, the oil should be replaced.
*11 Tyre rotation is recommended every 10,000 km.
*12 The Tyre Pressure Monitoring System (TPMS) initialization must be performed so that the system operates
normally (if equipped).
*13 Check the tyre repair fl uid expiration date every year when performing the periodic maintenance. Replace the
tyre repair fl uid bottle with new one before the expiration date.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 492 of 671
6–14
Maintenance and Care
Scheduled Maintenance
*4 If the vehicle is operated primarily under any of the following conditions, replace the engine oil and oil fi lter
more often than the recommended intervals.
a) Purpose of vehicle use is police car, taxi or driving school car.
b) Driving in dusty conditions
c) Extended periods of idling or low speed operation
d) Driving for long period in cold temperatures or driving regularly at short distance only
e) Driving in extremely hot conditions
f) Driving in mountainous conditions continually
*5 For SKYACTIV-D 1.5, reset the engine oil data after replacing the engine oil.
*6 Use of FL-22 is recommended when replacing engine coolant. Using engine coolant other than FL-22 may
cause serious damage to the engine and cooling system.
*7 If the vehicle is operated in very dusty or sandy areas, clean and if necessary, replace the air fi lter more often
than the recommended intervals.
*8 Inspect the battery electrolyte level, specifi c gravity and outer appearance. If the vehicle is operated in extremely
hot and cold areas, inspect the battery electrolyte level, specifi c gravity and appearance every 10,000 km (6,250
miles) or 6 months. The sealed battery only requires an outer appearance inspection.
*9 If the brakes are used extensively (for example, continuous hard driving or mountain driving) or if the vehicle is
operated in extremely humid climates, replace the brake fl uid annually.
*10 If the vehicle is operated primarily under any of the following conditions, replace the rear differential oil at
every 45,000 km (27,000 miles).
a) Towing a trailer or using a car-top carrier
b) Driving in dusty, sandy or wet condition
c) Extended periods of idling or low speed operation
d) Repeated short trips of less than 16 km (10 miles)
*11 If this component has been submerged in water, the oil should be replaced.
*12 The Tyre Pressure Monitoring System (TPMS) initialization must be performed so that the system operates
normally (if equipped).
*13 Check the tyre repair fl uid expiration date every year when performing the periodic maintenance. Replace the
tyre repair fl uid bottle with new one before the expiration date.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 495 of 671
6–17
Maintenance and Care
Owner Maintenance
Owner Maintenance Precautions
Routine Service
We highly recommend that these items be inspected daily, or at least every week.
Engine Oil Level (page 6-28 )
Engine Coolant Level (page 6-29 )
Brake and clutch Fluid Level (page 6-31 )
Washer Fluid Level (page 6-32 )
Battery Maintenance (page 6-38 )
Tyre Infl ation Pressure (page 6-42 )
Improper or incomplete service may result in problems. This section gives instructions only
for items that are easy to perform.
As explained in the Introduction (page 6-2 ), several procedures can be done only by a
qualifi ed service technician with special tools.
Improper do-it yourself maintenance during the warranty period may affect warranty
coverage. For details, read the separate Mazda Warranty statement provided with the
vehicle. If you are unsure about any servicing or maintenance procedure, have it done by an
expert repairer, we recommend an Authorised Mazda Repairer.
There are strict environmental laws regarding the disposal of waste oil and fl uids. Please
dispose of your waste properly and with due regard to the environment.
We recommend that you entrust the oil and fl uid changes of your vehicle to an Authorised
Mazda Repairer.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 504 of 671
6–26
Maintenance and Care
Owner Maintenance
NOTE
(SKYACTIV-G 2.0)
It is normal for all engines to consume engine oil under normal driving conditions. Engine oil consumption may be as high as 0.8 L/1000 km (1 L/800 miles). This may
be as a result of evaporation, internal ventilation or burning of the lubricating oil in
the working engine. Oil consumption may be higher when the engine is new due to
the running-in process. Oil consumption is also dependant on engine speed and engine
load. Under extreme driving conditions, oil consumption may be higher.
(SKYACTIV-D 1.5)
Whenever the engine oil is replaced, the vehicles engine control unit needs to be
reset as soon as possible. Otherwise the wrench indicator light or engine oil warning
light may turn on. To reset the engine control unit, consult an expert repairer, we
recommend an Authorised Mazda Repairer or refer to the vehicle engine control unit
reset procedure on page 6-27 .
Inspect the engine oil level periodically. When inspecting the engine oil, if the engine
oil level is exceeds the “X” mark on the dipstick, replace the engine oil. This should
be done by an expert repairer, we recommend an Authorised Mazda Repairer. When
replacing the engine oil, inspect the oil level using the oil dipstick and refi ll so that the
engine oil level is within the range between Full to Low as shown in the fi gure.
X Mark Full Low
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 506 of 671
6–28
Maintenance and Care
Owner Maintenance
Inspecting Engine Oil Level
1. Be sure the vehicle is on a level
surface.
2. Warm up the engine to normal
operating temperature.
3. Turn it off and wait at least 5 minutes
for the oil to return to the sump.
4. Pull out the dipstick, wipe it clean, and
reinsert it fully.
SKYACTIV-G 2.0
Full
LowOK
SKYACTIV-D 1.5
Full
OK
Low
NOTE
(SKYACTIV-D 1.5)
When inspecting the engine oil level,
pull out the dipstick straight without
twisting. In addition, when inserting
the dipstick, always insert it without
twisting so that the “X” mark faces the
front of the vehicle.
5. Pull it out again and examine the level.
The level is normal if it is between
Low and Full.
If it is near or below Low, add enough
oil to bring the level to Full.
CAUTION
Do not overfi ll the engine oil. This may
cause engine damage.
6. Make sure the O-ring on the dipstick is
positioned properly before reinserting
the dipstick.
7. Reinsert the dipstick fully.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 510 of 671
6–32
Maintenance and Care
Owner Maintenance
Window and Headlight
Washer Fluid
Inspecting Washer Fluid Level
WARNING
Use only windscreen washer fl uid or
plain water in the reservoir:
Using radiator antifreeze as washer
fl uid is dangerous. If sprayed on the
windscreen, it will dirty the windscreen,
affect your visibility, and could result in
an accident.
Inspect fl uid level in the washer fl uid
reservoir; add fl uid if necessary.
E
Use plain water if washer fl uid is
unavailable.
But use only washer fl uid in cold weather
to prevent it from freezing.
NOTE
Front and rear washer fl uid is supplied
from the same reservoir.
Body Lubrication
All moving points of the body, such as
door and bonnet hinges and locks, should
be lubricated each time the engine oil is
changed. Use a nonfreezing lubricant on
locks during cold weather.
Make sure the bonnet's secondary latch
keeps the bonnet from opening when the
primary latch is released.
$ 9 @ & ; & & % @ & E J U J P O J O E C
Page 583 of 671
7–37
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Signal Warning
Engine Oil Warning
Light This warning light indicates low engine oil pressure.
CAUTION
Do not run the engine if the oil pressure is low. Otherwise, it could result in
extensive engine damage.
If the light illuminates or the warning indication is displayed while driving:
1. Drive to the side of the road and park off the right-of-way on level ground.
2. Turn off the engine and wait 5 minutes for the oil to drain back into the sump.
3. Inspect the engine oil level 6-28 . If it's low, add the appropriate amount of engine oil
while being careful not to overfi ll.
CAUTION
Do not run the engine if the oil level is low. Otherwise, it could result in extensive
engine damage.
4. Start the engine and check the warning light.
If the light remains illuminated even though the oil level is normal or after adding oil,
stop the engine immediately and have your vehicle towed to an expert repairer, we
recommend an Authorised Mazda Repairer.
(Red)
High Engine Coolant
Temperature Warning
Light
The light fl ashes when the engine coolant temperature is extremely high, and
illuminates when the engine coolant temperature increases further.
Handling Procedure
Flashing light
Drive slowly to reduce engine load until you can fi nd a safe place to stop the vehicle
and wait for the engine to cool down.
Illuminated light
This indicates the possibility of overheating. Park the vehicle in a safe place
immediately and stop the engine.
Refer to Overheating 7-29 .
CAUTION
Do not drive the vehicle with the high engine coolant temperature warning light
illuminated. Otherwise, it could result in damage to the engine.
$ 9 @ & ; & & % @ & E J U J P O J O E C