turn signal MAZDA MODEL CX-30 2019 (in English) User Guide

The following lights turn on when the
leaving home light is operated.
Low beams, Position lights, Tail lights,
Number plate lights.
To turn on the lights
When the ignition switch and the
headlight switch are in the following
conditions, the headlights will
illuminate when the transmitter unlock
button is pressed and the vehicle
receives the transmitter signal. The
headlights turn off after a certain
period of time has elapsed (30
seconds).
xIgnition switch: off
xHeadlight switch: AUTO, , or
1. Lock button
2. Unlock button
NOTE
xOperation of the leaving home light
can be turned on or
off.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
xWhen the transmitter lock button is
pressed and the vehicle receives the
transmitter signal, the headlights turn
off.
xWhen the headlight switch is turned
to the OFF position, the headlights
turn off.
▼Headlight Levelling
The number of passengers and weight
of cargo in the luggage Compartment
change the angle of the headlights.
The angle of the headlights will be
automatically adjusted when turning
on the headlights.
A system malfunction or operation
conditions are indicated by a warning.
Refer to Exterior Light Warning
Indication/Warning Light on page
7-58.
▼Running Lights*
Some countries require moving
vehicles to have their lights on (running
lights) during the daytime.

The running lights turn on or off
automatically.

NOTE
(Except countries prohibited by law)
The running lights can be deactivated.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
When Driving
Switches and Controls
4-58*Some models.

Turn and Lane-Change
Signals
▼Turn and Lane-Change Signals
The ignition must be switched ON to
use the turn and lane-change signals.
▼Direction Indicators
Move the signal lever down (for a left
turn) or up (for a right turn) to the stop
position. The signal will self-cancel
after the turn is completed.

If the indicator light continues to flash
after a turn, manually return the lever
to its original position.
1. Right turn
2. Right lane change
3. OFF
4. Left lane change
5. Left turn

The direction indicators in the
instrument cluster flash according to
the operation of the direction indicator
lever to show which signal is working.

NOTE
xThere may be a problem with the
direction indicator lights if they do
not flash but remain turned on, or
they flash abnormally. Have your
vehicle inspected by an expert
repairer (we recommend an
Authorised Mazda Repairer).
xA personalised function is available
to change the turn indicator sound
volume.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
▼Lane-Change Signals
Move the lever halfway toward the
direction of the lane changeŠuntil the
indicator
flashesŠ and hold it there. It
will return to the off position when
released.
▼Three-Flash Turn Signal
After releasing the direction indicator
lever from the halfway point, the
direction indicator
flashes 3 times. The
operation can be cancelled by moving
the lever in the direction opposite to
which it was operated.
NOTE
The three-flash turn signal function can
be switched to on/off using the
personalisation function.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
When Driving
Switches and Controls
4-60

Hazard Warning Flasher
▼Hazard Warning Flasher
The hazard warning lights should
always be used when you stop on or
near a roadway in an emergency.

The hazard warning lights warn other
drivers that your vehicle is a traffic
hazard and that they must take
extreme caution when near it.

Depress the hazard warning flasher
and all the direction indicators will
flash. The hazard warning indicator
lights in the instrument cluster flash
simultaneously.
NOTE
xThe direction indicators do not work
when the hazard warning lights are
on.
xCheck local regulations about the
use of hazard warning lights while
the vehicle is being towed to verify
that it is not in violation of the law.
xIf the brake pedal is depressed while
driving on slippery roads, the
emergency stop signal system could
operate causing all the turn and lane
change signals to flash. Refer to
Emergency Stop Signal System on
page 4-78.
xWhile the emergency stop signal
system is operating, all the direction
indicators automatically flash rapidly
to caution the driver of a vehicle
following behind your vehicle of a
sudden braking situation. Refer to
Emergency Stop Signal System on
page 4-78.
When Driving
Switches and Controls
4-68

xThere is a problem with the
AUTOHOLD function.Emergency Stop Signal
System
▼Emergency Stop Signal System
If you apply the brakes suddenly while
driving at a speed of about 55 km/h
(34 mph) or faster, the emergency stop
signal system automatically and rapidly
flashes all the direction indicator lights
to caution drivers behind your vehicle
of the sudden braking situation.
NOTE
xFlashing
When you bring your vehicle to a
complete stop while all the direction
indicator lights are flashing rapidly,
the rapid
flashing of all the direction
indicator lights changes back to the
normal flashing pattern. The
direction indicator lights turn off
when you release your foot from the
brake pedal.
xOperation
xWhen the ABS operates, the
emergency stop signal system is
more likely to operate. Therefore, if
the brake pedal is depressed on a
slippery road, all of the direction
indicator lights may
flash.
xThe emergency stop signal system
does not operate when the hazard
warning light switch is pressed.
When Driving
Brake
4-78

High Beam Control
System (HBC)
*
▼High Beam Control System (HBC)
The HBC determines the conditions in
front of the vehicle using the Forward
Sensing Camera (FSC) while driving in
darkness to automatically switch the
headlights between high and low
beams.
Refer to Forward Sensing Camera
(FSC) on page 4-216.
While driving the vehicle at a speed of
about 30 km/h (19 mph) or more, the
headlights are switched to high beams
when there are no vehicles ahead or
approaching in the opposite direction.
The system switches the headlights to
low beams when one of the following
occurs:
xThe system detects a vehicle or the
headlights/lights of a vehicle
approaching in the opposite
direction.
xThe vehicle is driven on roads lined
with streetlamps or on roads in
well-lit cities and towns.
xThe vehicle is driven at less than
about 20 km/h (12 mph).
xThe headlight high-beam indicator
light turns on while the high beams
are on.
1. Forward Sensing Camera (FSC)*1
*1 The recognition distance of the Forward
Sensing Camera (FSC) varies according to
the surrounding conditions.
The warning light turns on when the
system has a malfunction.
Refer to High Beam Control System
(HBC) Warning Indication/Warning
Light (Amber) on page 7-58.
CAUTION
¾Do not adjust the vehicle height,
modify the headlight units, or
remove the camera, otherwise the
system will not operate normally.
¾Do not rely excessively on the HBC
and drive the vehicle while paying
sufficient attention to safety. Switch
the headlights between the high
beams and low beams manually if
necessary.
NOTE
The timing in which the system
switches the headlights changes under
the following conditions. If the system
does not switch the headlights
appropriately, manually switch
between high and low beams
according to the visibility as well as
road and traffic conditions.
xWhen there are sources of light in
the area such as street lamps,
illuminated signboards, and traffic
signals.
xWhen there are reflective objects in
the surrounding area such as
reflective plates and signs.
xWhen visibility is reduced under rain,
snow and foggy conditions.
xWhen driving on roads with sharp
turn or hilly terrain.
xWhen the headlights/rear lamps of
vehicles in front of you or in the
opposite lane are dim or not
illuminated.
When Driving
i-ACTIVSENSE
*Some models.4-99

xWhen there are other sources of light
in the area such as street lamps,
illuminated signboards, and traffic
signals.
xWhen there are reflective objects in
the surrounding area such as
reflective plates and signs.
xWhen visibility is reduced under rain,
snow and foggy conditions.
xWhen driving on roads with sharp
curves or undulations.
xWhen the headlights/rear lamps of
vehicles ahead or in the opposite
lane are dim or not illuminated.
xWhen there is insufficient darkness
such as at dawn or dusk.
xWhen the luggage compartment is
loaded with heavy objects or the rear
passenger seats are occupied.
xWhen visibility is reduced due to a
vehicle ahead spraying water from its
tyres onto your windscreen.
▼To Operate the System
The ALH operates to control Glare-Free
High Beam, Wide-Range Low Beam
and Highway Mode automatically after
the ignition is switched ON and the
headlight switch is in the
and
low beam position.
The ALH determines that it is dark
based on the brightness of the
surrounding area. At the same time,
the ALH indicator light (green) in the
instrument cluster illuminates.
NOTE
Operation of the ALH function can be
disabled.
Refer to the Settings section in the
Mazda Connect Owner's Manual.
▼Manual Switching
Switching to low beams
Switch the headlight switch to the
position, or press the ALH switch.
The ALH indicator light (green) turns
off.
1. ALH switch

If the ALH is turned off using the ALH
switch, press the ALH switch again to
turn the ALH back on.
Switching to high beams
Shift the lever to the high beam
position.
The ALH indicator light (green) turns
off and the headlight high-beam
indicator light is illuminated.
When Driving
i-ACTIVSENSE
4-102

NOTE
If the ignition is switched OFF while
you have cancelled the system using
the i-ACTIVSENSE switch, the system is
automatically enabled the next time
the ignition is switched ON. However,
if the system is cancelled using the
personalisation features, the system is
not automatically enabled.Blind Spot Monitoring
(BSM)
*
▼Blind Spot Monitoring (BSM)
The BSM is designed to assist the driver
in checking the area to the rear of the
vehicle on both sides during lane
changes by notifying the driver of the
presence of vehicles approaching from
the rear in an adjacent lane.
BSM operation
The BSM detects vehicles approaching
from the rear while travelling in the
forward direction at a speed of 30
km/h (19 mph) or faster and notifies
the driver by turning on the BSM
warning indicator light and displaying
the vehicle detection screen.
If the direction indicator lever is
operated to signal a turn in the
direction in which the BSM warning
indicator light is illuminated while the
approaching vehicle is detected, the
BSM notifies the driver of possible
danger
flashing on the BSM warning
indicator light, and by activating the
warning sound and the warning screen
indicator display.
The detection area on this system
covers the driving lanes on both sides
of the vehicle and from the rear part of
the front doors to about 50 m (164 ft)
behind the vehicle.
1. Your vehicle
When Driving
i-ACTIVSENSE
4-106*Some models.

BSM warning indicator lights when
they turn on.
Refer to Instrument Panel Illumination
on page 4-27.
Display indicator
The detected approaching vehicle and
warning are displayed in the
multi-information display and active
driving display (vehicles with active
driving display).
Multi-information Display
Active Driving Display (vehicles with
active driving display)
The detected direction is displayed
with a detection indicator (white)
when an approaching vehicle is
detected. In addition, if the direction
indicator lever is operated to signal a
lane change while the vehicle is
detected, the display changes the
colour (amber) of the warning
indicator.
BSM warning beep
The BSM warning beep is activated
simultaneously with the flashing of a
BSM warning indicator light.
▼Cancelling Operation of Blind Spot
Monitoring (BSM)
The BSM system can be set to
inoperable.
x(If only the BSM is turned off)
Refer to the Settings section in the
Mazda Connect Owner's Manual.
x(If the BSM is turned
off by
operating the i-ACTIVSENSE switch)
Refer to i-ACTIVSENSE Switch on
page 4-97.
NOTE
If the ignition is switched OFF while
you have cancelled the system using
the i-ACTIVSENSE switch, the system is
automatically enabled the next time
the ignition is switched ON. However,
if the system is cancelled using the
personalisation features, the system is
not automatically enabled.
When Driving
i-ACTIVSENSE
4-110

Tyre Pressure Monitoring
System (TPMS)
*
▼Tyre Pressure Monitoring System
(TPMS)
The TPMS monitors the air pressure of
each tyre and if it decreases below the
specified value, the system
notifies the
driver by turning on the TPMS warning
light in the instrument cluster and
indicating a message on the
multi-information display.
For the TPMS, the air pressure data
sent from the tyre pressure sensors
installed on each wheel via radio signal
is received by the receiver unit in the
vehicle to monitor the tyre pressures.
1. Tyre pressure sensors

In addition, the current tyre pressures
can be checked using the centre
display.
Refer to the Vehicle Status Monitor
section in the Mazda Connect
Owner's Manual.
NOTE
xWhen the ambient temperature is
low, the tyre temperatures also
decrease. If the tyre temperatures
decrease, the air pressure in the tyres
will also decrease which could turn
on the TPMS warning light.
xBefore driving, visually inspect the
tyres for abnormalities. Additionally,
inspect the tyre pressures monthly. A
digital type air pressure gauge is
recommended for inspecting the tyre
pressures.
The TPMS is not a substitute for your
own periodic inspection of the tyres.
Always inspect the tyres yourself
periodically.
CAUTION
¾Each tyre, including the spare (if
provided), should be checked
monthly when cold and inflated to
the inflation pressure recommended
by the vehicle manufacturer on the
vehicle placard or tyre
inflation
pressure label. (If your vehicle has
tyres of a different size than the size
indicated on the vehicle placard or
tyre inflation pressure label, you
should determine the proper tyre
inflation pressure for those tyres.)
As an added safety feature, your
vehicle has been equipped with a
tyre pressure monitoring system
(TPMS) that illuminates a low tyre
pressure telltale when one or more
of your tyres is
significantly
under-inflated. Accordingly, when
the low tyre pressure telltale
illuminates, you should stop and
check your tyres as soon as possible,
and inflate them to the proper
pressure. Driving on a significantly
under-inflated tyre causes the tyre to
overheat and can lead to tyre failure.
Under-inflation also reduces fuel
efficiency and tyre tread life, and may
affect the vehicle's handling and
stopping ability.
When Driving
Tyre Pressure Monitoring System (TPMS)
4-232*Some models.

Please note that the TPMS is not a
substitute for proper tyre
maintenance, and it is the driver's
responsibility to maintain correct tyre
pressure, even if under-inflation has
not reached the level to trigger
illumination of the TPMS low tyre
pressure telltale.
Your vehicle has also been equipped
with a TPMS malfunction indicator to
indicate when the system is not
operating properly.
The TPMS malfunction indicator is
combined with the low tyre pressure
telltale. When the system detects a
malfunction, the telltale will flash for
approximately one minute and then
remain continuously illuminated.
This sequence will continue upon
subsequent vehicle start-ups as long
as the malfunction exists. When the
malfunction indicator is illuminated,
the system may not be able to detect
or signal low tyre pressure as
intended. TPMS malfunctions may
occur for a variety of reasons,
including the installation of
replacement or alternate tyres or
wheels on the vehicle that prevent
the TPMS from functioning properly.
Always check the TPMS malfunction
telltale after replacing one or more
tyres or wheels on your vehicle to
ensure that the replacement or
alternate tyres and wheels allow the
TPMS to continue to function
properly.
¾To avoid false readings, the system
samples for a little while before
indicating a problem. As a result it
will not instantaneously register a
rapid tyre deflation or blow out.▼If there is a problem with the Tyre
Pressure Monitoring System
(TPMS)
If the TPMS warning light flashes, there
may be a problem with the system.
Consult an expert repairer (we
recommend an Authorised Mazda
Repairer) to have the system inspected.
Refer to Tyre Pressure Monitoring
System (TPMS) Warning Indication/
Warning Light (Flashing) on page
7-57.
In the following cases, the system
cannot recognise the tyre pressures
correctly and the TPMS warning light
may flash.
xThere is equipment or a device
nearby emitting radio signals the
same as a tyre pressure sensor.
xA metallic object such as a
non-genuine electronic device is
installed near the centre of the
instrument panel (obstructs the radio
signals from the tyre pressure sensors
to the receiver).
xA device such as one of the following
is used in the cabin.
xElectronic devices such as a
computer.
xConverter devices such as a
DC-AC converter.
xThere is a large accumulation of
snow or ice around the vehicle tyres.
xThe battery in a tyre pressure sensor
is dead.
xA wheel not equipped with a tyre
pressure sensor is used.
xTyres employing steel in the sidewall
of the tyre are installed.
xTyre chains are used.
▼When a tyre pressure decreases
If the TPMS warning light turns on, a
tyre pressure may be low. Inspect the
When Driving
Tyre Pressure Monitoring System (TPMS)
4-233