fuel MAZDA MODEL CX-5 2017 (in English) User Guide

3–63
Before Driving
Towing
Parking
Always make sure the tires of the trailer and the tow vehicle are blocke\
d while parked.
Apply the parking brake fi rmly and put the transaxle in P.
Avoid parking on an incline, but if you must, follow these instructions:
1. Depress and hold down the brake pedal.
2. Have a helper put wheel blocks against the downhill side of all vehicle \
and trailer tires.
3. Then release the brake pedal slowly until the blocks bear the load.
 If the grade is downhill, turn the steering wheel so that the front of t\
he front tires face the curb.
 If it is uphill, face the rear of the front tires against the curb.
4. Firmly apply the parking brake.
5. Shift the transaxle into P, and stop the engine.

To restart after parking on an incline:
1. With the transaxle in P, start the engine. (Be sure to depress and hold the brake pedal.)
2. Shift into gear.
3. Release the parking brake (also the foot brake) and pull away from the\
wheel blocks. Stop; apply the parking brake and shift into P.
4. Have a helper retrieve the wheel blocks.

Fuel consumption
Trailer towing causes higher fuel consumption.
Maintenance
If you tow a trailer frequently, have your vehicle serviced as shown in Scheduled
Maintenance (page 6-4 ).
CX-5_8FN1-EA-16L_Edition1.indb 632016/12/12 10:05:40

4–1*Some models.
4When Driving
Information concerning safe driving and stopping.

Start/Stop Engine ................................ 4-4 Ignition Switch ............................... 4-4
Starting the Engine ......................... 4-5
Turning the Engine Off ................ 4-10

Instrument Cluster and Display ...... 4-12 Meters and Gauges ....................... 4-12
Multi-information Display and INFO
Switch
* ......................................... 4-20
Active Driving Display * ............... 4-28
Warning/Indicator Lights ............. 4-32

Manual Transaxle Operation ........... 4-39 Manual Transaxle Shift Pattern .... 4-39

Automatic Transaxle ......................... 4-42 Automatic Transaxle Controls ..... 4-42
Shift-Lock System ....................... 4-43
Transaxle Ranges ......................... 4-43
Manual Shift Mode ...................... 4-45
Driving Tips ................................. 4-50
Switches and Controls ...................... 4-51
Lighting Control ........................... 4-51
Fog Lights
* ................................... 4-57
Turn and Lane-Change Signals .... 4-57
Windshield Wipers and Washer ... 4-58
Rear Window Wiper and
Washer .......................................... 4-62
Rear Window Defogger ............... 4-62
Horn ............................................. 4-65
Hazard Warning Flasher ............... 4-65
HomeLink Wireless Control
System
* ......................................... 4-66

Brake .................................................. 4-70 Brake System ............................... 4-70
AUTOHOLD ............................... 4-75
Hill Launch Assist (HLA) ............ 4-81

ABS/TCS/DSC ................................... 4-82 Antilock Brake System (ABS) ..... 4-82
Traction Control System (TCS) ... 4-83
Dynamic Stability Control
(DSC) ........................................... 4-85

Fuel Economy Monitor ..................... 4-86 Fuel Economy Monitor
* ............... 4-86

Drive Selection ................................... 4-88 Drive Selection ............................. 4-88

i-ACTIV AWD ................................... 4-89 i-ACTIV AWD Operation
* ........... 4-89

CX-5_8FN1-EA-16L_Edition1.indb 12016/12/12 10:05:40

4–5
When Driving
Start/Stop Engine
ON
This is the normal running position after
the engine is started. The indicator light
(amber) turns off. (The indicator light
(amber) illuminates when the ignition
is switched ON and the engine is not
running.)
Some indicator lights/warning lights
should be inspected before the engine is
started (page 4-32 ).
NOTE
When the push button start is pressed to
ON, the sound of the fuel pump motor
operating near the fuel tank can be heard.
This does not indicate an abnormality.

Starting the Engine
WARNING
Radio waves from the key may aff ect
medical devices such as pacemakers: Before using the key near people who
use medical devices, ask the medical
device manufacturer or your physician
if radio waves from the key will aff ect
the device.

CX-5_8FN1-EA-16L_Edition1.indb 52016/12/12 10:05:40

4–8
When Driving
Start/Stop Engine
7. Press the push button start after both the KEY indicator light (green) (if
equipped) in the instrument cluster and
the push button start indicator light
(green) illuminate.
NOTE
  After starting the engine, the push
button start indicator light (amber)
turns off and the ignition switches to the
ON position.
  After pressing the push button start and
before the engine starts, the operation
sound of the fuel pump motor from near
the fuel tank can be heard, however, this
does not indicate a malfunction.

8. After starting the engine, let it idle for about ten seconds.
NOTE
  Whether the engine is cold or warm, it
should be started without the use of the
accelerator.
  If the engine does not start the fi rst
time, refer to Starting a Flooded Engine
under Emergency Starting. If the engine
still does not start, have your vehicle
inspected by an Authorized Mazda
Dealer (page 7-17 ).

Engine Start Function When Key Battery is Dead
CAUTION
When starting the engine by holding
the transmitter over the push button
start due to a dead key battery or a
malfunctioning key, be careful not
to allow the following, otherwise the
signal from the key will not be received
correctly and the engine may not start.
 Metal parts of other keys or metal
objects touch the key.

 Spare keys or keys for other vehicles equipped with an immobilizer
system touch or come near the key.

 Devices for electronic purchases, or security passage touch or come near
the key.

CX-5_8FN1-EA-16L_Edition1.indb 82016/12/12 10:05:41

4–13
When Driving
Instrument Cluster and Display


Dashboard Illumination..................................................\
........................................ page 4-16



Trip Computer and INFO Switch ........................................................................\
... page 4-17



Engine Coolant Temperature Gauge ...................................................................... page 4-15



Fuel Gauge ..................................................................\
........................................... page 4-15



Outside Temperature Display ................................................................\
................. page 4-17



Cruise Control Set Vehicle Speed Display ............................................................. page 4-17



Multi-information Display and INFO Switch ........................................................ page 4-20



Active Driving Display ........................................................................\
.................. page 4-28
Speedometer
The speedometer indicates the speed of the
vehicle.
Odometer, Trip Meter and Trip Meter Selector (Without Multi-
information Display)
The display mode can be changed from
odometer to trip meter A to trip meter B
and then back to odometer by pressing the
selector while one of them is displayed.
The selected mode will be displayed.


Selector
Press the selector Press the selector
Press the selector
Odometer
Trip meter A
Trip meter B


Odometer
The odometer records the total distance
the vehicle has been driven.
Trip meter
The trip meter can record the total distance
of two trips. One is recorded in trip meter
A, and the other is recorded in trip meter
B.

For instance, trip meter A can record the
distance from the point of origin, and
trip meter B can record the distance from
where the fuel tank is
fi lled.

When trip meter A is selected, pressing
the selector again within one second will
change to trip meter B mode.

When trip meter A is selected, TRIP A
will be displayed. When trip meter B is
selected, TRIP B will be displayed.

The trip meter records the total distance
the vehicle is driven until the meter
is again reset. Return it to “0.0” by
depressing and holding the selector for
one second or more. Use this meter to
measure trip distances and to compute fuel
consumption.
CX-5_8FN1-EA-16L_Edition1.indb 132016/12/12 10:05:42

4–14
When Driving
Instrument Cluster and Display
NOTE
  (Vehicles with type B audio)  If the fuel economy data is reset using
the fuel economy monitor, or trip A
is reset using the trip meter when the
function which synchronizes the fuel
economy monitor and the trip meter is
on, the fuel economy data and trip A are
reset simultaneously.
 Refer to Fuel Economy Monitor on page 4-86 .
  Only the trip meters record tenths of
kilometers (miles).
  The trip record will be erased when:   The power supply is interrupted
(blown fuse or the battery is
disconnected).
  The vehicle is driven over 9999.9 km
(mile).


Tachometer
The tachometer shows engine speed in
thousands of revolutions per minute (rpm).
CAUTION
Do not run the engine with the
tachometer needle in the RED ZONE.
This may cause severe engine damage.
Instrument Cluster


STRIPED
ZONE
RED ZONE
*
1The range varies depending on the type
of gauge. *
1
*1

NOTE
When the tachometer needle enters the
STRIPED ZONE, this indicates to the
driver that the gears should be shifted
before entering the RED ZONE.


CX-5_8FN1-EA-16L_Edition1.indb 142016/12/12 10:05:42

4–15
When Driving
Instrument Cluster and Display
Engine Coolant Temperature Gauge (Without Multi-information
Display)
Displays the engine coolant temperature.
The white gauge indicates that the engine
coolant temperature is low, and the red
gauge indicates that the engine coolant
temperature is high and overheating.


CAUTION
If the engine coolant temperature
gauge indicator fl ashes, there is a
possibility of overheating. Park the
vehicle in a safe place immediately
and take appropriate measures. If the
vehicle continues to be driven, it could
cause damage to the engine.
Refer to Overheating on page 7-18 .

NOTE
  The temperature unit (Centigrade/
Fahrenheit) of the engine coolant gauge
display changes in conjunction with
the temperature unit of the outside
temperature display.
 Refer to Personalization Features on page 9-11 .
  During normal driving, the engine
coolant temperature stabilizes at
100 °C (210 °F) or less, and the gauge
indicates a range lower than 100 °C
(210 °F).
  If the engine load increases and the
engine coolant temperature exceeds
100 °C (210 °F), the gauge indicates the
engine coolant temperature.

Fuel Gauge (Without Multi-information Display)
The fuel gauge shows approximately
how much fuel is remaining in the tank
when the ignition is switched ON. We
recommend keeping the tank over 1/4 full.


Full
1/4 Full
Empty

If the low fuel warning light illuminates or
the fuel level is very low, refuel as soon as
possible.
Refer to Warning Indication/Warning
Lights on page 4-33 .
CX-5_8FN1-EA-16L_Edition1.indb 152016/12/12 10:05:42

4–16
When Driving
Instrument Cluster and Display
NOTE
  After refueling, it may require some
time for the indicator to stabilize. In
addition, the indicator may deviate
while driving on a slope or curve since
the fuel moves in the tank.
  The display indicating a quarter or less
remaining fuel has more segments to
show the remaining fuel level in greater
detail.
  The direction of the arrow ( )
indicates that the fuel- fi ller lid is on the
left side of the vehicle.

Dashboard Illumination
(Without auto-light control)
When the position lights are turned
on with the ignition switched ON, the
brightness of the dashboard illumination is
dimmed.
(With auto-light control)
When the position lights are turned
on with the ignition switched ON, the
brightness of the dashboard illumination
is dimmed. However, when the light
sensor detects that the surrounding area is
bright such as when the position lights are
turned on in the daytime, the dashboard
illumination does not dim.
NOTE
   (With auto-light control)  When the ignition is switched ON in the
early evening or at dusk, the dashboard
illumination is dimmed for several
seconds until the light sensor detects
the brightness of the surrounding area,
however, the dimmer may cancel after
the brightness is detected.
  When the position lights are turned on,
the position lights indicator light in the
instrument cluster turns on.
 Refer to Headlights on page 4-51 .
The brightness of the instrument cluster
and dashboard illuminations can be
adjusted by rotating the knob.
  The brightness decreases by rotating the
knob to the left. A beep sound will be
heard when the knob has been rotated to
the maximum dim position.
   The brightness increases by rotating the
knob to the right.


Dim
Bright

Function for cancelling illumination
dimmer
The illumination dimmer can be canceled
by rotating the dashboard illumination
knob to the right until a beep sound is
heard while the instrument cluster is
dimmed with the ignition switched ON.
If the instrument cluster's visibility is
reduced due to glare from surrounding
brightness, cancel the illumination
dimmer.
CX-5_8FN1-EA-16L_Edition1.indb 162016/12/12 10:05:43

4–17
When Driving
Instrument Cluster and Display
NOTE
  (With Multi-information Display)  The illumination dimmer can be
canceled by pressing the dashboard
illumination knob.
  When the illumination dimmer is
canceled, the instrument cluster cannot
be dimmed even if the position lights are
turned on.
  When the illumination dimmer is
canceled, the screen in the center
display switches to constant display of
the daytime screen.

Outside Temperature Display (Without Multi-information
Display)
When the ignition is switched ON, the
outside temperature is displayed.



NOTE
Under the following conditions, the
outside temperature display may differ
from the actual outside temperature
depending on the surroundings and vehicle
conditions:
  Signifi cantly cold or hot temperatures.  Sudden changes in outside temperature.  The vehicle is parked.  The vehicle is driven at low speeds.

Changing the Temperature Unit of the
Outside Temperature Display
The outside temperature unit can be
switched between Celsius and Fahrenheit.
Settings can be changed by operating the
center display screen.
Refer to Personalization Features on page
9-11 .
NOTE
When the temperature unit indicated in the
outside temperature display is changed,
the temperature unit indicated in the
engine coolant gauge display changes in
conjunction with it.

Cruise Control Set Vehicle Speed
Display (Without Multi-
information Display)
The vehicle speed preset using the cruise
control is displayed.



Trip Computer and INFO Switch (Without Multi-information
Display)
The following information can be selected
by pressing the INFO switch with the
ignition switched ON.
   Distance-to-empty mode  Average fuel economy mode  Current fuel economy mode  Compass mode
If you have any problems with your trip
computer, consult an Authorized Mazda
Dealer.
CX-5_8FN1-EA-16L_Edition1.indb 172016/12/12 10:05:43

4–18
When Driving
Instrument Cluster and Display
Distance-to-empty mode
This mode displays the approximate
distance you can travel on the remaining
fuel based on the fuel economy.

The distance-to-empty will be calculated
and displayed every second.


NOTE
  Even though the distance-to-empty
display may indicate a suf fi cient amount
of remaining driving distance before
refueling is required, refuel as soon as
possible if the fuel level is very low or
the low fuel warning light illuminates.
   The display may not change unless you
add more than approximately 9 L
(2.3 US gal, 1.9 Imp gal) of fuel.
  The distance-to-empty is the
approximate remaining distance the
vehicle can be driven until all the
graduation marks in the fuel gauge
(indicating the remaining fuel supply)
disappear.
  If there is no past fuel economy
information such as after fi rst
purchasing your vehicle or the
information is deleted when the battery
cables are disconnected, the actual
distance-to empty/range may differ from
the amount indicated.

Average fuel economy mode
This mode displays the average fuel
economy by calculating the total fuel
consumption and the total traveled
distance since purchasing the vehicle, re-
connecting the battery after disconnection,
or resetting the data. The average fuel
economy is calculated and displayed every
minute.



To clear the data being displayed, press the
INFO switch for more than 1.5 seconds.
After pressing the INFO switch,
- - - L/100 km (- - - mpg) will be displayed
for about 1 minute before the fuel
economy is recalculated and displayed.
Current fuel economy mode
This mode displays the current fuel
economy by calculating the amount of fuel
consumption and the distance traveled.

Current fuel economy will be calculated
and displayed every 2 seconds.



When you've slowed to about 5 km/h
(3 mph), - - - L/100 km (- - - mpg) will be
displayed.
CX-5_8FN1-EA-16L_Edition1.indb 182016/12/12 10:05:43