key MAZDA MODEL MPV 2002 (in English) Owner's Manual

5-31
Driving Your Mazda
Warning/Indicator Lights and Beeps
Form No. 8Q44-EA-01K

Seat Belt Warning Beep
If the driver’s seat belt is not fastened
when the ignition switch is turned to the
ON position, a beep will sound for about
6 seconds.

Ignition Key Reminder
If the ignition switch is in the LOCK or
ACC position, a beep will sound when the
driver’s door is opened.

Lights-On Reminder
If lights are on and the key is removed
from the ignition switch, a beep will
sound when the driver’s door is opened.

Power Sliding Door Buzzer
The buzzer sounds according to the power
sliding door operation.
If there is a malfunction in the power
sliding door system, the buzzer sounds
continuously. If this happens, press the
power sliding doors main switch to the
OFF position and the buzzer will stop.
Consult your nearest Authorized Mazda
Dealer to have the power sliding doors
checked.
Refer to Power Sliding Doors on page 3-
12.
Beeps
J16L_EA.book Page 31 Friday, February 22, 2002 11:34 AM

5-32
Driving Your Mazda
Form No. 8Q44-EA-01K
Switches and Controls

Headlights
To turn on the lights, turn the knob on the
end of the control lever.

Lights-On Reminder
If lights are on and the key is removed
from the ignition switch, a beep will
sound when the driver’s door is opened.

Headlight High-Low Beam
Push the lever forward for high beams.
Pull it back for low.

Flashing the Headlights
To flash the headlights, pull the lever fully
toward you. The headlight switch need
not be on, and the lever will return to the
normal position when released.
Lighting Control
Lever Position OFF
Headlights Off Off On
Taillights
Parking lights
License lights
Side-marker lightsOff On On
NOTE
To prevent discharging the battery,
don’t leave the lights on while the
engine is off.
High beams
Low beams
J16L_EA.book Page 32 Friday, February 22, 2002 11:34 AM

6-41
Interior Comfort
Form No. 8Q44-EA-01K
Interior Equipment
When you need a sunvisor, lower it for use
in front or swing it to the side.

Va n i t y M i r r o r s
To use the vanity mirror, lower the
sunvisor.
If your vehicle is equipped with a vanity
mirror light, it will illuminate when you
pull the cover up.

Illuminated Entry System
When the switch is in the DOOR position,
the overhead light, the luggage
compartment light and the courtesy lights
come on for:
•about 30 seconds after the driver’s door
is unlocked and the ignition key is
removed.
•about 15 seconds after all doors are
closed.
•about 15 seconds after the key is
removed from the ignition.
The light also goes out when:
•the ignition switch is turned to the ON
position and all doors are closed.
•the driver’s door is locked.
Sunvisors
Sunvisor
Interior Lights
NOTE
If any door is left opened, the light
goes out after about 5 minutes.
The light turns on again when the
ignition switch is turned to the ON
position, or when any door is opened
after all doors have been closed.
J16L_EA.book Page 41 Friday, February 22, 2002 11:34 AM

6-49
Interior Comfort
Interior Equipment
Form No. 8Q44-EA-01K

Glove Box
To open the glove box, pull the latch
toward you.
The door has a lock, insert the key and
turn it clockwise to lock,
counterclockwise to unlock.

Front Console
Pull the latch to open.

Under Seat Tray
(Front Passenger Seat Only)
Lift the latch and pull the tray forward.

Storage Box (In Seat Side Table)
To use the storage box
1. Raise the table.
2. Push the button to open.
Unlock
Lock
Button
J16L_EA.book Page 49 Friday, February 22, 2002 11:34 AM

7-11
In Case of an Emergency
Flat Tire
Form No. 8Q44-EA-01K
4. Insert the jack lever and attach the jack
handle to tire jack.
5. Turn the jack handle clockwise and
raise the vehicle high enough so that
the spare tire can be installed. Before
removing the lug nuts, make sure your
Mazda is firmly in position and that it
cannot slip or move.
6. Remove the lug nuts by turning them
counterclockwise; then remove the
wheel.
Locking Lug Nuts
If your vehicle has optional antitheft
wheel lug nuts, one on each wheel will
lock the tires and you must use a special
key to unlock them. This key is attached
to the lug wrench and is stored with the
spare tire. Register them with the lock
manufacturer by filling out the card
provided in the glove box and mailing it in
the accompanying envelope. If you lose
your key, consult an Authorized Mazda
Dealer or use the lock manufacturer’s
order form, which is with the registration
card.
To remove an antitheft lug nut
1. Get the key for the locking lug nut.
2. Place it on top of the nut, and be sure to
hold the key square to it. If you hold
the key at an angle, you may damage
both key and nut. Don’t use a power
impact wrench.
3. Place the lug wrench on top of the key
and apply pressure. Turn the wrench
counterclockwise.
Jack handle
Jack lever
Antitheft lug nutSpecial key
J16L_EA.book Page 11 Friday, February 22, 2002 11:34 AM

7-12
In Case of an Emergency
Flat Tire
Form No. 8Q44-EA-01K
To replace the nut
1. Place the key on top of the nut.
2. Place the lug wrench on top of the key,
apply pressure, and turn it clockwise.

Mounting the Spare Tire
1. Remove dirt and grime from the
mounting surfaces of the wheel and
hub, including the hub bolts, with a
cloth.
2. Mount the spare tire.3. Install the lug nuts with the beveled
edge inward; tighten them by hand.
Removing Dirt and Grime from
Wheels, Hubs and Hub Bolts:
When changing or replacing a tire,
not removing dirt and grime from the
mounting surfaces of the wheel, hub
and hub bolts is dangerous. The lug
nuts could loosen while driving and
cause the tire to come off, resulting in
an accident. Make sure the mounting
surfaces of the wheel, hub and lug
nuts are clean before changing or
replacing tires.
WARNING
Applying Oil and Grease to Lug Nuts,
Bolts:
Applying oil or grease to lug nuts and
bolts is dangerous. The lug nuts could
loosen while driving and cause the
tire to come off, resulting in an
accident. In addition, lug nuts and
bolts could be damaged if tightened
more than necessary. Do not apply oil
or grease to lug nuts and bolts and do
not tighten the lug nuts beyond the
recommended tightening torque.
WARNING
J16L_EA.book Page 12 Friday, February 22, 2002 11:34 AM

7-17
In Case of an Emergency
Form No. 8Q44-EA-01K
Emergency Starting
If the engine fails to start, it may be
flooded (excessive fuel in the engine).
Follow this procedure:
1. Depress the accelerator all the way and
hold it there.
2. Turn the ignition switch to the START
position and hold it there—for up to 10
seconds. If the engine starts, release the
key and accelerator immediately
because the engine will suddenly rev
up.
3. If the engine fails to start, crank it
without using the accelerator—for up
to 10 seconds.Jump-starting is dangerous if done
incorrectly. So follow the procedure
carefully. If you feel unsure about jump-
starting, we strongly recommend that you
have a competent service technician do
the work.
1. Make sure the booster battery is 12 V
and that its negative terminal is
grounded.
Starting a Flooded EngineJump-Starting
Battery-Related Explosion:
Flames and sparks near open battery
cells are dangerous. Hydrogen gas,
produced during normal battery
operation, could ignite and cause the
battery to explode. An exploding
battery can cause serious burns and
injuries. Keep all flames, including
cigarettes, and sparks away from
open battery cells.
Low Fluid Level or Frozen Battery:
Jump-starting a frozen battery or one
with a low fluid level is dangerous. It
may rupture or explode, causing
serious injury.
Don’t jump-start a frozen battery or
one with a low fluid level.
Use only a 12 V booster system. You
can damage a 12 V starter, ignition
system, and other electrical parts
beyond repair with a 24 V power
supply (two 12 V batteries in series or
a 24 V motor generator set).
WARNING
CAUTION
J16L_EA.book Page 17 Friday, February 22, 2002 11:34 AM

8-7
Maintenance and Care
Owner Maintenance
Form No. 8Q44-EA-01K
Improper or incomplete service may result in problems. This section gives instructions
only for items easy to perform.
As explained in the Introduction (page 8-2), several procedure can be done only by a
qualified service technician with special tools.
Improper owner maintenance during the warranty period may affect warranty coverage.
For details, read the separate Mazda Warranty statement provided with the vehicle. If
you’re unsure about any servicing or maintenance procedure, have it done by an
Authorized Mazda Dealer.
There are strict environmental laws regarding the disposal of waste oil and fluids. Please
dispose of your waste carefully and with due regard to the environment.
We recommend that you entrust the oil and fluid changes of your vehicle to an Authorized
Mazda Dealer.
Owner Maintenance Precautions
Maintenance Procedures:
Performing maintenance work on a vehicle is dangerous if not done properly. You can
be seriously injured while performing some maintenance procedure. If you lack
sufficient knowledge and experience or the proper tools and equipment to do the
work, have it done by a qualified technician.
Running the Engine:
Working under the hood with the engine running is dangerous. It becomes even more
dangerous when you wear jewelry or loose clothing.
Either can become entangled in moving parts and result in injury.
Therefore, if you must run the engine while working under the hood, make certain
that you remove all jewelry (especially rings, bracelets, watches, and necklaces) and
all neckties, scarves, and similar loose clothing before getting near the engine or
cooling fan.
Electrical Fan and Engine Inspection:
Inspecting the engine with the ignition switch in the ON position is dangerous. The
cooling fan could come on unexpectedly even when the engine isn’t running. You
could be seriously injured by the fan. Turn the ignition switch off and remove the key
from the ignition switch when you inspect the engine.
WARNING
J16L_EA.book Page 7 Friday, February 22, 2002 11:34 AM

8-35
Maintenance and Care
Owner Maintenance
Form No. 8Q44-EA-01K

Fuse Panel Description
Fuse block (Engine compartment)
DESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
1 DEFOG 40ARear window
defroster
2 BTN 60ASTOP, HAZARD,
ROOM, D.LOCK
and DRL fuses
3 ABS 60AAntilock brake
system,
For protection of
various circuits
4 FAN1 30A Cooling fan
5 FAN2 30A Cooling fan
6 HEATER 40A Heater
7 R.HEATER 30ARear heater,
For protection of
various circuits
8 IG KEY2 40AA/C, P.WIND,
SUN ROOF and
R.WIP fuses
9 A/C 10AAir conditioner,
For protection of
various circuitsDESCRIPTIONFUSE
RATINGPROTECTED
COMPONENT
10 TAIL 15A Taillights
11 (A/C PWR) 15A Inverter
12 HORN 15A Horn
13 (FOG) (15A)For protection of
various circuits
14 EEC 5AFor protection of
various circuits
15 HEAD L 15A Headlight-left
16 HEAD R 15A Headlight-right
17 (HID L) (20A)—
18 (HID R) (20A)—
19 IG KEY1 60AMETER,
ENGINE and
WIPER fuses
20 EGI INJ 30AFor protection of
various circuits
21 FUEL PUMP 20A Fuel pump
22 MAIN 120AFor protection of
all circuits
J16L_EA.book Page 35 Friday, February 22, 2002 11:34 AM

11-2
Form No. 8Q44-EA-01K
Index
A
Accessory Sockets ........................... 6-51
Add-On Non-Genuine Parts and
Accessories
...................................... 9-11
Air Bag Systems
.............................. 2-47
Air Conditioning System
Gas specifications
..................... 10-5
Air Filter
.......................................... 8-17
Antenna
............................................ 6-14
Anti-Lock Brake System (ABS)
........ 5-7
Warning light
.............................. 5-7
Appearance Care
.............................. 8-38
Ashtrays
........................................... 6-44
Audio System
................................... 6-14
Audio set
................................... 6-21
Operating tips for audio
system
....................................... 6-14
Safety certification
.................... 6-40
Automatic Transaxle
Driving tips
............................... 5-11
Fluid
.......................................... 8-15
Overdrive
.................................. 5-11
Shift-lock override
.................... 5-10
Shift-lock system
...................... 5-10
Transaxle ranges
......................... 5-9
B
Battery
Emergency starting
................... 7-17
Maintenance
............................. 8-22
Specifications
........................... 10-4
Beeps
Ignition key reminder
............... 5-31
Lights-on reminder
................... 5-31
Power sliding door buzzer
........ 5-31
Seat belt warning beep
.............. 5-31
Before Starting the Engine
................. 4-6
After getting in
........................... 4-6
B
Before getting in ......................... 4-6
Body Lubrication
............................. 8-17
Bottle Holders
.................................. 6-47
Brake
Fluid
.......................................... 8-13
Brakes
Anti-lock brake system (ABS)
....5-7
Foot brake
................................... 5-4
Pad wear indicator
...................... 5-8
Parking brake
.............................. 5-5
Warning light
.............................. 5-5
Break-In Period
.................................. 4-7
Bulb Replacement
............................ 8-27
C
Capacities ......................................... 10-5
Carbon Monoxide
.............................. 4-5
Cargo Securing Loops
...................... 6-50
Catalytic Converter
............................ 4-3
Cell Phones
...................................... 9-12
Child Restraint
Child restraint precautions
........ 2-35
Installing child-restraint
systems
...................................... 2-38
LATCH child-restraint
systems
...................................... 2-44
Child Safety Locks for Rear
Door
................................................. 3-11
Cigarette Lighter
.............................. 6-44
Climate Control System
.....................6-2
Cruise Control
.................................. 5-13
Cup Holders
..................................... 6-46
Customer Assistance
.......................... 9-2
J16L_EA.book Page 2 Friday, February 22, 2002 11:34 AM