turn signal bulb MAZDA MODEL PROTÉGÉ 2002 Owners Manual (in English)

5-34
Driving Your Mazda
Switches and Controls
Form No. 8Q36-EA-01F

Turn Signal
Move the signal lever down (for a left
turn) or up (for a right turn) to the stop
position. The signal will self-cancel after
the turn is completed.
If the indicator light continues to flash
after a turn, manually return the lever to
its original position.
Green indicators on the dashboard show
which signal is working.
Lane-change signals
Move the lever slightly toward the
direction of the change —until the
indicator flashes— and hold it there. It
will return to the off position when
released.Use this switch to turn on the fog lights.
They help you to see as well as to be seen.
To turn on the fog lights, first turn on the
headlight switch. Then press the fog light
switch.
To turn the fog lights off, press the fog
light switch again or turn the headlight
switch off.
Turn and Lane-Change
Signals
NOTE
If an indicator light stays on without
flashing or if it flashes abnormally, the
turn signal bulb may be burned out.
Right turn
Left turn Right lane
change
Left lane
changeOFF
Fog Lights
J39L(02MY).book Page 34 Thursday, November 1, 2001 10:49 AM

8-30
Maintenance and Care
Owner Maintenance
Form No. 8Q36-EA-01F
Light Bulbs
License plate lights Front side-marker lights
Overhead lights/Map lights Sedan
Headlights
Front turn signal lights/
Parking lights
Brake lights/Taillights
Rear turn signal lights
Reverse lights
Taillights
High-mount brake light
Trunk light
Rear side-marker lights
J39L(02MY).book Page 30 Thursday, November 1, 2001 10:49 AM

8-35
Maintenance and Care
Owner Maintenance
Form No. 8Q36-EA-01F

Replacing a Bulb (Front)
To replace the fog light bulbs, contact an Authorized Mazda Dealer.
To replace the front side-marker light bulbs (Hatchback), contact an Authorized Mazda
Dealer.
Front turn signal lights/Parking lightsFront side-marker lights
Sedan
J39L(02MY).book Page 35 Thursday, November 1, 2001 10:49 AM

8-37
Maintenance and Care
Owner Maintenance
Form No. 8Q36-EA-01F

Replacing a Bulb (Rear)
Rear bulb access
(Sedan)
To replace the turn signal light, brake
light/taillight, side-marker light or reverse
light bulb, the trunk end trim must be
removed and the inside cover must be
partially opened.
1. Pull the center section of the plastic
retainer and remove the retainers and
the trunk end trim.
2. Remove the inside cover’s plastic
retainers and partially open the inside
cover.(Hatchback)
To replace the turn signal light, brake
light/taillight or reverse light bulb, remove
the caps and the cover.
Jack cover
J39L(02MY).book Page 37 Thursday, November 1, 2001 10:49 AM

8-38
Maintenance and Care
Owner Maintenance
Form No. 8Q36-EA-01F
Brake lights/Taillights
Rear side-marker lights
Reverse lights
Taillights
Rear turn signal lights
High-mount brake light (Sedan) License plate lights
Trunk light (Sedan)
Sedan
Sedan
Hatchback
Hatchback Brake lights/Taillights
Rear turn signal lights
Reverse lights
Sedan
To replace the high-
mount brake light bulb,
contact an Authorized
Mazda Dealer.
J39L(02MY).book Page 38 Thursday, November 1, 2001 10:49 AM

10-7
Specifications
Form No. 8Q36-EA-01F

Light Bulbs

Tires
Standard tire
Temporary spare tire

Fuses
Refer to the fuse rating on page 8-39.
Light bulb Wattage
HeadlightsSedan 60/55
HatchbackHi 60
Lo 55
Front turn signal/Parking lights 27/8
Fog lights 55
Rear turn signal lights 21
Front side-marker lights 5
Rear side-marker lights (Sedan) 3.8
Taillights (Sedan) 3.8
Brake lights/Taillights 21/5
High-mount brake
lightSedanType A 21
Ty p e B 5 . 8
Hatchback 5.8
Reverse lights 21
License plate lights 5
Trunk light (Sedan) 5
Luggage compartment light (Hatchback) 5
Overhead lightType A 10
Type B and C 8
Map lights 5
Tire sizeInflation pressure
Front Rear
P185/65R14 85S
220 kPa (2.2 kgf/cm
2, 32 psi or lb/po2) 220 kPa (2.2 kgf/cm2, 32 psi or lb/po2)
185/65R14 86T
210 kPa (2.1 kgf/cm2, 30 psi or lb/po2) 210 kPa (2.1 kgf/cm2, 30 psi or lb/po2)
P195/55R15 84V
220 kPa (2.2 kgf/cm2, 32 psi or lb/po2) 220 kPa (2.2 kgf/cm2, 32 psi or lb/po2)
195/55R15 85V
210 kPa (2.1 kgf/cm2, 30 psi or lb/po2) 210 kPa (2.1 kgf/cm2, 30 psi or lb/po2)
P195/50R16 83V
220 kPa (2.2 kgf/cm2, 32 psi or lb/po2) 220 kPa (2.2 kgf/cm2, 32 psi or lb/po2)
Tire size Inflation pressure
T125/70 D14
420 kPa (60 psi)
T115/70 D15
J39L(02MY).book Page 7 Thursday, November 1, 2001 10:49 AM