jump cable MERCEDES-BENZ AMG GT S 2017 C190 Owner's Manual

Jump-starting
For the jump-starting procedure, use only the jump-starting connection point in the engine com-
partment, consisting of a positive terminal and a ground point.
!Avoid repeated and lengthy starting attempts. Otherwise, the catalytic converter could be
damaged by the non-combusted fuel.
Do not start the vehicle using a rapid charging device. If your vehicle's battery is discharged, the
engine can be jump-started from another vehicle or from a second battery using jumper cables.
Observe the following points:
RThe battery is not accessible in all vehicles. If the other vehicle's battery is not accessible, jump-
start the vehicle using a second battery or a jump-starting device.
RYou may only jump-start the vehicle when the engine and exhaust system are cold.
ROnly jump-start from batteries with a 12 V voltage rating.
ROnly use jumper cables which have a sufficient cross-section and insulated terminal clamps.
RIf the battery is fully discharged, leave the battery that is being used to jump-start connected for
a few minutes before attempting to start. This charges the battery slightly.
RMake sure that the two vehicles do not touch.
Make sure that:
RThe jumper cables are not damaged.
RBare parts of the terminal clamp do not come into contact with other metal parts while the jumper
cables are connected to the battery.
RThe jumper cables cannot come into contact with parts which can move when the engine is
running, such as the V-belt pulley or the fan.
XSecure the vehicle by applying the electric parking brake.
XShift the transmission to position P.
XMake sure that the ignition is switched off. All indicator lamps in the instrument cluster must be
off. When using the SmartKey, turn the SmartKey to position 0in the ignition lock and remove it
(
Ypage 103).
XSwitch off all electrical consumers, e.g. rear window defroster, lighting, etc.
XOpen the hood.
Vehicles with carbon engine cover:
XTurn fasteners :one Õturn and remove.
XRemove cover.
All vehicles:
248Jump-starting
Breakdown assistance

Position numberBidentifies the charged battery of the other vehicle or an equivalent jump-starting
device.
XSlide cover Aof positive terminal :in the direction of the arrow.
XConnect positive terminal :on your vehicle to positive terminal ;of donor battery Busing the
jumper cable. Always begin with positive terminal :on your own vehicle first.
XStart the engine of the donor vehicle and run it at idling speed.
XConnect negative terminal =of donor battery Bto ground point ?of your vehicle using the
jumper cable, connecting the jumper cable to donor battery Bfirst.
XStart the engine.
XBefore disconnecting the jumper cables, let the engine run for several minutes.
XFirst, remove the jumper cables from ground point ?and negative terminal =, then from pos-
itive clamp :and positive terminal ;. Begin each time at the contacts on your own vehicle first.
XAfter removing the jumper cables, close cover Aof positive terminal :.
Vehicles with carbon engine cover:
XReplace the jump-starting connection point cover. Make sure all mountings for the fasteners are
positioned precisely behind the corresponding recesses in the cover.
XPress the fasteners into the mountings. Turn the fasteners by Õof a turn to engage.
All vehicles:
XHave the battery checked at a qualified specialist workshop.
Jump-starting is not considered to be a normal operating condition.
iJumper cables and further information regarding jump-starting can be obtained at any qualified
specialist workshop.
Jump-starting249
Breakdown assistance
Z

XCheck the transmission position using the
indicatorinthe multifunction display
(
Ypage 110).
XRelease the brake pedal.
XRelease the electricparking brake.
XSwit ch on the hazard warning lamps
(Ypage 88).
In order to signal a change of direction when
to wing the veh icle with the hazard warning
lamps switched on, use the co mbination switch
as usual. Inthis case, only the indicator lamps
for the direction of travel flash. After resetting
the co mbination switch, the hazard warning
lamp starts flashing again.
Transporting the vehicle
!When the veh icle isloaded for transport, the
front and rear axles must bestationary and on
the same transportation veh icle. Positioning
over the connection point of the transport
veh icle is not permitte d.The drive train may
otherwise be damaged.
!You may only secure the veh icle bythe
wheels, not byparts of the veh iclesuch as
axle or steering components. Otherwise, the
veh icle could bedamaged.
The to wingeye can beused to pullthe veh icle
onto a trailer or transporter for transporting pur- poses.
XIn sert the SmartKey into the ignition lock. You
must use the SmartKey instead of the Start/
St op button (
Ypage 103).
XStart the engine and leave itrunning during
the entire loading operation.
XMove the transmission to position Nwit h the
E-SELECT lever.
XCheck the transmission position using the
indicator in the multifunction display
(
Ypage 110).
As soon as the vehicle has been loaded:
XPrevent the vehicle from rolling away by
applying the electric parking brake.
XShift the automatic transmission to posi-
tion P.
XTurn the SmartKey to position 0in the ignition
lock and remove it.
XSecure the vehicle.
Tow-starting (emergency engine
starting)
!
Vehicles with automatic transmission must
not be tow-starte d.You could otherwise dam-
age the automatic transmission.
iYou can find information on "Jump-starting"
under (Ypage 248).
Fuses
Important safety notes
GWARNING
If you manipulate or bridge a faulty fuse or if
you replace itwith a fuse with a higher amper-
age, the electric cables could beoverloaded.
This could result ina fire. There is a risk of an
accident and injury.
Alwa ys replace faulty fuses with the specified
new fuses having the correct amperage.
Blo wn fuses must bereplaced with fuses of the
same rating, which you can recognize bythe
color and value. The fuse ratings are listed in the
fuse allocation chart.
The fuse allocation chart is on the fuse box in the
cargo compartment (
Ypage 253).
If a newly inserted fuse also blows, have the
cause traced and rectified at a qualified special-
ist workshop, e.g. an authorized Mercedes-Benz
Center.
!Only use fuses that have been approved for
Mercedes-Benz vehicles and which have the
252Fuses
Breakdown assistance