112 MERCEDES-BENZ C-Class 2008 W204 Comand Manual

Content
Importing vCards from a
PCMCIA card . . . . . . . . . . . . . . . . 110
Navigation . . . . . . . . . . . . . . . . . . . . 111
Introduction . . . . . . . . . . . . . . . . . . . . 112
Safety instructions . . . . . . . . . . . . 112
Updating the map software . . . . . 112
General information . . . . . . . . . . . 115
Input restriction . . . . . . . . . . . . . . 116
Menu overview . . . . . . . . . . . . . . . 117
Switching to navigation mode . . . 118
Basic settings . . . . . . . . . . . . . . . . 120
Destination input . . . . . . . . . . . . . . . . 126
Introduction to destination input . 126
Entering a destination via the address
126
Entering a destination from the desti-
nation memory . . . . . . . . . . . . . . . 135
Entering destination from the last des-
tinations . . . . . . . . . . . . . . . . . . . . 137
Entering destination via the map . 137
Entering stopover destination. . . . 138
POI input . . . . . . . . . . . . . . . . . . . . . . 141
Entering a POI in local area of
destination . . . . . . . . . . . . . . . . . . 141
Entering a POI in the vicinity of the
location . . . . . . . . . . . . . . . . . . . . . 141Entering a POI in the vicinity of a
specific location . . . . . . . . . . . . . . 141
Entering a POI via a name search . 141
Entering a POI via a phone number
search . . . . . . . . . . . . . . . . . . . . . . 141
Choosing a POI category . . . . . . . 142
Entering a POI via the map . . . . . . 147
Route guidance . . . . . . . . . . . . . . . . . 148
General information . . . . . . . . . . . 148
Driving maneuver . . . . . . . . . . . . . 148
Example display without driving
maneuver . . . . . . . . . . . . . . . . . . . 150
Traffic lane recommendations . . . 150
Destination or destination region
reached. . . . . . . . . . . . . . . . . . . . . 152
Off-road and off-map . . . . . . . . . . 152
Navigation announcements . . . . . 153
Cancelling route guidance . . . . . . 154
Resuming route guidance after
cancelling . . . . . . . . . . . . . . . . . . . 154
Detour function. . . . . . . . . . . . . . . 154
Alternative route . . . . . . . . . . . . . . 155
Route browser . . . . . . . . . . . . . . . 155
Displaying destination information . . .
155
Destination memory . . . . . . . . . . . . . . 157
Home address . . . . . . . . . . . . . . . 157Saving a destination in the
destination memory . . . . . . . . . . . 159
Deleting destination or home
address from the destination
memory. . . . . . . . . . . . . . . . . . . . . 161
Last destinations . . . . . . . . . . . . . . . . 162
Saving a destination permanently
in the destination memory . . . . . . 162
Saving vehicle location in the last
destinations . . . . . . . . . . . . . . . . . 162
Saving crosshairs position in the
last destinations . . . . . . . . . . . . . . 162
Deleting one of the last
destinations . . . . . . . . . . . . . . . . . 162
System settings. . . . . . . . . . . . . . . . 163
System settings . . . . . . . . . . . . . . . . . 164
Opening System menu . . . . . . . . . 164
Menu overview . . . . . . . . . . . . . . . 164
Display settings . . . . . . . . . . . . . . 164
Time settings . . . . . . . . . . . . . . . . 165
Read-out settings . . . . . . . . . . . . . 166
Voice control settings . . . . . . . . . . 167
Bluetooth® settings . . . . . . . . . . . 169
Reset. . . . . . . . . . . . . . . . . . . . . . . 171
Setting the system language . . . . 171
Tele Aid*. . . . . . . . . . . . . . . . . . . . . . . 172

19 At a glance
COMAND control system
FunctionPage
1Switching to radio mode
Switching wavebands
Switching to SatRadio*
mode40
42
45
2Switching to CD audio,
DVD audio or MP3 mode
Switching to DVD video
mode
60
77
3Disc slot
Loading CDs/DVDs
Ejecting CDs/DVDs
Updating the map soft-
ware
54
57
112
4Load/Eject button
5Clear button for functions
Entering a phone number
Deleting digit or entire
entry
101
95
6Tuning to a station via the
station memory
42, 42
6Storing stations manually
Selecting DVD changer
compartments
Entering a phone number
Sending DTMF tones43, 43
101
102
7Tuning to a station via sta-
tion search
Fast forward
Selecting next track
42
63, 78
63
8Switching COMAND on/
off
35
9Setting the volume35
aSlot for PCMCIA memory
card
bEject button for
PCMCIA memory card
58
cTuning to a station via sta-
tion search
Fast reverse
Selecting previous track
42
63, 78
63
FunctionPage
dAnswering calls
Initiating calls
Redial101
94,101
101
eRejecting calls
Ending an active call101
103
fOpening System menu164
gMute
Switching hands-free mi-
crophone on/off
Switching traffic and navi-
gation announcements off35
102
35
hSwitching to phone mode
92
jSwitching to navigation
mode
Displaying menu system
118
119
FunctionPage

111 Navigation
Introduction . . . . . . . . . . . . . . . . .112
Destination input . . . . . . . . . . . .126
POI input . . . . . . . . . . . . . . . . . . .141
Route guidance . . . . . . . . . . . . . .148
Destination memory . . . . . . . . . .157
Last destinations . . . . . . . . . . . .162

112 Navigation
Introduction
The digital data for the map software will
become obsolete, just like conventional
road maps. Optimum route guidance by
the navigation system is only achieved
with up-to-date map software. Information
on new map software versions is available
from an authorized Mercedes-Benz Center.
You can have the map software updated
there by means of a DVD or perform the
update process yourself.
Notes on DVD discs

Only touch the discs at the edges.

Handle the discs with care in order to
prevent reading errors.

Avoid scratching, leaving fingerprints
and dust on the discs.

Use a commercially available cleaning
cloth to clean discs. Always wipe in a
straight line from the inside outwards,
never in a circular motion.

After use, put the discs back into the
box.

Protect the discs from heat and direct
sunlight.
Introduction
Safety instructions
G Warning
For safety reasons, only enter a destination
when the vehicle is stationary. When the ve-
hicle is in motion, a passenger should enter
the destination. Study manual and select
route before driving.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your vehicle is
covering a distance of 44 feet (approximate-
ly 14 m) every second.
COMAND calculates the route to the desti-
nation without taking account of the follow-
ing:

Traffic lights

Stop and right-of-way signs

Lane merging

Parking or stopping prohibited areas

Other road and traffic rules and regula-
tions

Narrow bridges
G Warning
COMAND may give incorrect navigation
commands if the data in the digital map
does not correspond with the actual road/
traffic situation. Digital maps do not cover
all areas nor all routes within an area. For ex-
ample, if the traffic routing has been
changed or the direction of a one-way road
has been reversed.
For this reason, you must always observe
applicable road and traffic rules and regula-
tions during your journey. Road and traffic
rules and regulations always have priority
over the navigation commands generated by
the system.
G Warning
Navigation announcements are intended to
direct you while driving without diverting
your attention from the road and driving.
Please always use this feature instead of
consulting the map display for directions.
Consulting the symbols or map display for
directions may cause you to divert your at-
tention from driving and increase your risk
of an accident.
Updating the map software

115 Navigation
Introduction
An unsuccessful update may be caused by
one of the following:

DVD dirty or scratched.
Clean the DVD.
Please refer to the “Notes on DVD
discs” section (
page 112).
Restart the update.

Overheating as a result of excessively
high temperatures in the passenger
compartment.
Wait until the passenger compart-
ment has cooled down.
Restart the update.

The memory medium (hard drive) inte-
grated into COMAND has a physical de-
fect.
Contact an authorized
Mercedes-Benz Center.Operational readiness of the navigation
system after the system software up-
date
Sometimes the installed map software is
no longer compatible following a system
software update by an authorized
Mercedes-Benz Center. In this case, the
navigation system is not operational.
To update map software: Proceed as
described in the “Update process” sec-
tion (
page 114). Use map software
compatible with the system software.
i Please note that in this case the update
must run through right to the end. If you cancel
beforehand, the navigation system will still not
be ready for operation.
After start-up or initial start-up, the naviga-
tion system must perform a position find-
ing operation. As a result, you may have to
drive for some time until precise route
guidance takes place.
GPS reception
The correct functioning of the navigation
system is also dependent on the GPS re-
ception. In certain situations, the GPS re-
ception may be impaired, distorted or even
impossible, e. g. in tunnels, multi-storey
car parks or due to snow on the GPS anten-
na. If there is snow on the GPS antenna,
you should remove it. The GPS antenna is
at the rear on the vehicle’s roof.
Route guidance after vehicle transport
After vehicle transport (e. g. by ferry, car
train or by towing) COMAND must deter-
mine the vehicle location again.
Position finding takes place automatically
when the vehicle is driven off again, even if
COMAND is switched off. The actual length
of time may vary from case to case.
While the vehicle is determining its posi-
tion, route guidance is subject to the fol-
lowing restrictions:

Navigation announcements, route
guidance displays and displayed street
names do not match the actual loca-
tion.
General information

135 Navigation
Destination input
Starting route calculation
i Route calculation can only be started once
all the necessary address data has been en-
tered.
In the Enter Destination menu select
“Start”.
1Destination
2Starts route calculation and then starts
route guidance
If route guidance is not active yet, the
route calculation is started.
If route guidance is already active, you
will be prompted to confirm that route
guidance should be ended.
Select “Yes” or “No”.If you select “Yes” COMAND cancels
route guidance and starts the route cal-
culation to the newly entered destina-
tion.
If you select “No” COMAND resumes
the active route guidance.
During the route calculation, an arrow
points towards the destination, and un-
derneath the message “Calculating
Fast Route...”, for example, is dis-
played.
Route guidance begins after the route
has been calculated (
page 148).
i Route calculation takes some time. The
length of time depends on, e. g. distance to the
destination. COMAND calculates the route using
the digital map data. The calculated route may
deviate from the actual road situation, e. g. as a
result of road works or incomplete map data.
Please refer to the information on the digital map
(
page 112).
If necessary switch to navigation mode
and display menu system
(
page 118).
Select “Destination” K “From Memo-
ry”.
If there are more than 8 entries in the
destination memory, the destination
memory list with predictive speller
(
page 136) is displayed, otherwise
the destination memory list is dis-
played without predictive speller
(
page 137).
i There is always an entry in the destination
memory with the name “My Address”. You can
assign your home address, for example, to this
entry and select it for route guidance
(
page 157). This entry is at the top of the list
in the destination memory.
Entering a destination from the des-
tination memory