wipers MERCEDES-BENZ CLA 2014 User Guide

XRemove the cover in the front wheel
housing (Ypage 112).
XTurn housing covercounter-clockwise
and pull it out.
XTurn bulb holdercounter-clockwise and
pull it out.
XTake the bulb out of bulb holder.
XInsertthe new bulb into bulb holder.
XInsert bulb holderinto the lamp and turn
it clockwise.
XAlign housing coverand turn it
clockwise until it engages.
XReplace the cover in the front wheel
housing (Ypage 112).
High-beam headlamps/daytime
running lamps/parking lamps/
standing lamps (vehicles with halogen
headlamps)
XSwitch off the lights.
XOpen the hood.
XTurn housing covercounter-clockwise
and pull it out.
XTurn bulbcounter-clockwise and pull it
out.
XInsert the new bulb and engage it to the
stop.
XAlign housing coverand turn it
clockwise until it engages.
Turn signals (halogen headlamps)
XSwitch off the lights.
XOpen the hood.
XTurn bulb holdercounter-clockwise and
pull it out.
XTake the bulb out of bulb holder.
XInsert the new bulb into bulb holder.
XInsert bulb holderand turn it clockwise
until it engages.
Cornering light function (Intelligent
Light System)
XSwitch off the lights.
XOpen the hood.
XTurn housing covercounter-clockwise
and pull it out.
XTurn bulb holdercounter-clockwise and
pull it out.
XTake the bulb out of bulb holder.
XInsert the new bulb into bulb holder.
Replacing bulbs113
Lights and windshield wipers
Z

XInsert bulb holderinto the lamp and turn
it clockwise.
XAlign housing coverand turn it
clockwise until it engages.
Changing the rear bulbs
Opening and closing the side trim
panels
You must open the side trim panel in the trunk
before you can change the bulbs in the tail
lamps.
Left-hand side trim panel
XTo open:turn release knob90° in the
direction of the arrow and remove side trim
panel.
XTo close:insert side trim paneland turn
release knob90° in the opposite
direction to the arrow.
Right-hand side trim panel
XTo open:loosenside trim panelat the
top and fold it down in the direction of the
arrow.
XTo close:insert side panel.
Tail lamp
XSwitch off the lights.
XOpen the trunk.
XOpen the side trim panel (Ypage 114).
XRelease and remove connector.
XPress retaining clipsat the same time in
the direction of the arrows.
XPull the bulb holder out with the bulbs.
Bulb holder
Brake lamp
Brake lamp
"Rear fog lamp
!Backup lamp
Turn signal
114Replacing bulbs
Lights and windshield wipers

XBrake lamp/rear fog lamp/backup
lamp:remove the corresponding bulb from
the bulb holder.
XInsert the new bulb into the bulb holder.
XTurn signal lamp:lightly press the bulb
into the bulb holder, turn it counter-
clockwise and remove it from bulb holder.
XInsert the new bulb into the bulb holderand
turn it clockwise.
XReinsert the bulb holderand engage on
retaining clips.
XRe-establish contact with the connector.
XClose the side trim panel (Ypage 114).
Windshieldwipers
Switching the windshield wipers on/
off
!Do not operate the windshield wipers
when the windshield is dry, as this could
damage the wiper blades. Moreover, dust
that has collected on the windshield can
scratch the glass if wiping takes place when
the windshield is dry.
If it is necessary to switch on the windshield
wipers in dry weather conditions, always
use washer fluid when operating the
windshield wipers.
!If the windshield wipers leave smears on
the windshield after the vehicle has been
washed in an automatic car wash, wax or
other residues may be the reason for this.
Clean the windshield using washer fluid
after washing the vehicle in an automatic
car wash.
Combination switch
Windshield wiper off

Intermittentwipe, low (rain sensor
set to low sensitivity)
Intermittentwipe, high (rain sensor
set to high sensitivity)
Continuous wipe, slow
Continuous wipe, fast
Single wipe/To wipe the
windshield using washer fluid
XSwitch on the ignition.
XTurn the combination switch to the
corresponding position.
!Vehicles with a rain sensor: if the
windshield becomes dirty in dry weather
conditions, the windshield wipers may be
activated inadvertently. This could then
damage the windshield wiper blades or
scratch the windshield.
For this reason, you should always switch
off the windshield wipers in dry weather.
Vehicles witharain sensor:in the
or
position, the appropriate wiping
frequency is automatically set according to
the intensity of the rain. In theposition,
the rainsensor is more sensitive than in
the
position, causing the windshield
wipers to wipe more frequently.
If the wiper blades are worn, the windshield
will no longer be wiped properly. This could
prevent you from observing the traffic
conditions.Replace the wiper blades twice a
year, ideally in spring and fall.
Windshield wipers115
Lights and windshield wipers
Z

Replacing the wiper blades
Important safety notes
GWARNING
If the windshield wipers begin to move while
you are changing the wiper blades, you could
be trapped by the wiper arm.There is a risk
of injury.
Always switch off the windshield wipers and
ignition before changing the wiper blades.
!To avoid damaging the wiper blades,
make sure that you touch only the wiper
arm of the wiper.
!Never open the hood if a windshield wiper
arm has been folded away from the
windshield.
Never fold a windshield wiper arm without
a wiper blade back onto the windshield.
Hold the windshield wiper arm firmly when
you change the wiper blade. If you release
the windshield wiper arm without a wiper
blade and it falls onto the windshield, the
windshield may be damaged by the force of
the impact.
Mercedes-Benzrecommends that you have
the wiper blades changed ataqualified
specialist workshop.
Changing the windshield wiper blades
Removing the wiper blades
XRemove the SmartKey from the ignition
lock.
XFold the wiper arm away from the
windshield.
XPress both release clips.
XFold wiper bladein the direction of
arrow"away from wiper arm!.
XRemove wiper bladein the direction of
arrow.
Installing the wiper blades
XPosition new wiper bladewith
recess on lug.
XFold wiper bladein the direction of
arrow"onto the wiper arm, until retaining
clipsengage in bracket!.
XMake sure that wiper bladeis seated
correctly.
XFold the wiper arm back onto the
windshield.
116Windshieldwipers
Lights and windshield wipers

Problems with the windshield wipers
ProblemPossible causes/consequences and
Solutions
The windshield wipers
are jammed.
Leaves or snow, for example, may be obstructing the windshield
wiper movement.The wiper motor has been deactivated.
XFor safety reasons, you should remove the SmartKey from the
ignition lock.
XRemove the cause of the obstruction.
XSwitch the windshield wipers back on.
The windshield wipers
fail completely.
The windshield wiper drive is malfunctioning.
XSelect another wiper speed on the combination switch.
XHave the windshield wipers checked at a qualified specialist
workshop.
The windshield washer
fluid from the spray
nozzles no longer hits
the center of the
windshield.
The spray nozzles are misaligned.
XHave the spray nozzles adjusted at a qualified specialist
workshop.
Windshield wipers117
Lights and windshield wipers
Z

Dual-zone automatic climate control
XActivate the"Cooling with air
dehumidification" function.
XActivate automatic mode.
XIf the windows continue to fog up, activate
the "Windshield defrosting" function.
iYou should only select this setting until
the windshield is clear again.
Windows fogged up on the outside
XActivate the windshield wipers.
XSetthe air distribution toor.
iYou should only select this setting until
the windshield is clear again.
Rear window defroster
Activating/deactivating
The rear window defroster has a high current
draw. You should therefore switch it off as
soon as the rear window is clear. Otherwise,
the rear window defroster switches off
automatically after several minutes.
If the battery voltage is too low, the rear
window defroster may switch off.
XTurn the SmartKey to position2in the
ignition lock (Ypage 137).
XPress thebutton.
The indicator lamp in thebutton lights
up or goes out.
130Operating the climate control systems
Climate control

GWARNING
If you switch off the ignitionwhile driving,
safety-relevant functions are only available
with limitations, or not at all. This could affect,
for example, the power steering and the brake
boosting effect.You will require considerably
more effort to steer and brake. There is a risk
of an accident.
Do not switch off the ignition while driving.
GWARNING
If the parking brake has not been fully
released when driving, the parking brake can:
Roverheat and cause a fire
Rlose its hold function.
There is a risk of fire and an accident.Release
the parking brake fully before driving off.
!Warm up the engine quickly. Do not use
the engine's full performance until it has
reached operating temperature.
Only shift the automatic transmission to
the desired drive position when the vehicle
is stationary.
Where possible, avoid spinning the drive
wheels when pulling away on slippery
roads. You could otherwise damage the
drive train.
!AMG vehicles:avoid full-load operation
and engine speeds greater than 5000rpm
when the engine is cold. This helps to
protect the engine and avoids
uncomfortable driving.
Key positions
\rTo remove the SmartKey
(shift the transmission to positionP)
Power supply for some consumers, such
as the windshield wipers
Ignition (power supply for all consumers)
and drive position
To start the engine
iThe SmartKey can be turned in the
ignition lock even if it is not the correct
SmartKey for the vehicle. The ignition is not
switched on. The engine cannot be started.
Starting the engine
Important safety notes
GWARNING
Combustion engines emit poisonous exhaust
gases such as carbon monoxide. Inhaling
these exhaust gases leads to poisoning. There
is a risk of fatal injury. Therefore never leave
the engine running in enclosed spaces
without sufficient ventilation.
GWARNING
Flammable materials introduced through
environmental influence or by animals can
ignite if in contact with the exhaust system or
parts of the engine that heat up. There is a risk
of fire.
Carry out regular checks to make sure that
there are no flammable foreign materials in
Driving137
Driving and parking
Z

Display messagesPossible causes/consequences and
Solutions
Wiper
Malfunctioning
The windshield wipers are malfunctioning.
XVisit a qualified specialist workshop.
Hazard Warning
Flashers
Malfunctioning
The hazard warning lamps are faulty.
XVisit a qualified specialist workshop.
SmartKey
Display messagesPossible causes/consequences and
Solutions

Key Does Not
Belong to Vehicle
You have put the wrong SmartKey in the ignition lock.
XUse the correct SmartKey.

TakeYourKeyfrom
Ignition
The SmartKey is in the ignition lock.
XRemove the SmartKey.

Obtain a New Key
The SmartKey needs to be replaced.
XVisit a qualified specialist workshop.
Warning and indicator lamps in the instrument cluster
Seatbelts
ProblemPossible causes/consequences and
Solutions

After starting the
engine, the red seat
belt warning lamp lights
up for six seconds.
The seat belt warning lamp reminds the driver and frontpassenger
to fasten their seat belts.
XFastenyour seat belt (Ypage 50).

After starting the
engine, the red seat
belt warning lamp lights
up. In addition, a
warning tone sounds
for up to six seconds.
The driver's seat belt is not fastened.
XFasten your seat belt (Ypage 50).
The warning tone ceases.
240Warning and indicator lamps in the instrument cluster
On-board computer and displays

iMake sure that you clear the memory of
the integrated garage door opener before
selling the vehicle.
Compass
Calling up the compass
The compass displays in which compass
direction the vehicle is currently traveling:N,
NE,E,SE,S,SW,WorNW.
To receive a correct display in rear-view
mirror, the compass must be calibrated
and the magnetic field zone set.
Setting the compass
XDetermine your position using the following
zone maps.
North America zone map
South America zone map
XPush a round pen into opening
"(Ypage 276) for approximately three
seconds.
The zone currently selected appears in
compass display(Ypage 276).
XTo selectthe zone:push a round pen into
opening"(Ypage 276) until the desired
zone is selected.
If, after a few seconds, the display in
compass display(Ypage 276) changes
direction, the zone has been selected.
Calibrating the compass
XMake sure that there is sufficient space for
you to drive in a circle without impeding
traffic.
In order to calibrate the compass correctly,
do the following:
Rcalibrate the compass in the open and not
in the vicinity of steel structures or high-
voltage transmission lines.
Rswitch off electrical consumers such as the
climate control, windshield wipers or rear
window defroster.
Rclose all doors and the trunk lid.
XSwitch on the ignition.
XPush a round pen into opening
"(Ypage 276) for approximately six
276Features
Stowage and features

Useful information
iThis Operator's Manual describes all
models and all standard and optional
equipment of your vehicle available at the
time of publication of the Operator's
Manual. Country-specific differences are
possible. Please note that your vehicle may
not be equipped with all features
described. This also applies to safety-
related systems and functions.
iRead the information on qualified
specialist workshops: (Ypage 25).
Engine compartment
Hood
Important safety notes
GWARNING
If the hood is unlatched, it may open up when
the vehicle is in motion and block your view.
There is a risk of an accident.
Never unlatch the hood while driving.
GWARNING
When opening and closing the hood, it may
suddenly fall into the closed position.There is
a risk of injury to persons within range of
movement of the hood.
Open and close the hood only when no one is
within its range of movement.
GWARNING
Certain components in the engine
compartment, such as the engine, radiator
and parts of the exhaust system, can become
very hot. Working in the engine compartment
poses a risk of injury.
Where possible, let the engine cool down and
touch only the components described in the
following.
GWARNING
Opening the hood when the engine is
overheated or when there is a fire in the
engine compartmentcould expose you to hot
gases or other service products. There is a
risk of injury.
Let an overheated engine cool down before
opening the hood. If there is a fire in the
engine compartment, keep the hood closed
and contact the fire department.
GWARNING
The engine compartment contains moving
components. Certain components, such as
the radiator fan, may continue to run or start
again suddenly when the ignition is off. There
is a risk of injury.
If you need to do any work inside the engine
compartment,
Rswitch off the ignition
Rnever reach into the area where there is a
risk of danger from moving components,
such as the fan rotation area
Rkeep clothing away from moving parts
GWARNING
The ignition system and the fuel injection
system work under high voltage. If you touch
components which are under voltage, you
could get an electric shock. There is a risk of
injury.
Never touch components of the ignition
system or fuel injection system when the
ignition is switched on.
Opening the hood
GWARNING
When the hood is open and the windshield
wipers are set in motion,you can be injured
by the wiper linkage. There is a risk of injury.
Always switch off the windshield wipers and
the ignition before opening the hood.
280Engine compartment
Maintenance and care