stop start MERCEDES-BENZ CLS 2014 Workshop Manual

Tires
Display messagesPossible causes/consequencesandSolutions
Check
TirePressure Soon
The tire pressure loss warningsystem has detectedasignificant
lossinpressure.
Awarning tone also sounds.
GWARNING
Withtirepressureswhichare toolow, there isariskofthe
following hazards:
Rthey may burst, especiallyasthe load and vehicle speed
increase.
Rthey may wear excessively and/or unevenly, which may greatly
impair tire traction.
Rthe driving characteristics, as well as steering and braking, may
be greatly impaired.
There isarisk of an accident.
XStop the vehicle without making any sudden steering or braking
maneuvers. Pay attention to the traffic conditionsasyou do so.
XSecure the vehicle against rolling away (Ypage 167).
XCheck the tires and, if necessary, follow the instructions for a
flat tire (Ypage 321).
XCheck the tire pressures and, if necessary, correct the tire
pressure.
XRestart the tire pressure loss warning system when the tire
pressure is correct (Ypage 342).
CheckTirePressure
Then Restart Run
Flat Indicator
The tire pressure loss warning system generatedadisplay
message and has not been restarted since.
XSet the correct tire pressure in all four tires.
XRestart the tire pressure loss warning system (Ypage 342).
Run Flat Indicator
Inoperative
The tire pressure loss warning system is faulty.
XVisitaqualified specialist workshop.
Rectify
Tire Pressure
The tire pressure is too low in at least one of the tires, or the tire
pressure difference between the wheels is too great.
XCheck the tire pressures at the next opportunity (Ypage 342).
XIf necessary, correct the tire pressure.
XRestart the tire pressure monitor (Ypage 345).
258Display messages
On-board computer and displays

Display messagesPossible causes/consequences andSolutions

Don't Forget Your
Key
The display message is shown foramaximum of 60 seconds and
is onlyareminder.
You have opened the driver'sdoor with the engine switched off.
The KEYLESS-GO key is not in the ignitionlock.
XRemember to take the KEYLESS-GO key with you when you
leave the vehicle.

Key Not Detected
(red display message)
The KEYLESS-GO key is not in the vehicle.
Awarning tone also sounds.
If theengineisswitched off,you can no longer lockthe vehicle
centrally or start the engine.
XPull over and stop the vehicle safely as soon as possible, paying
attention to road and traffic conditions.
XSecure the vehicle against rolling away (Ypage 167).
XLocate the KEYLESS-GO key.
The KEYLESS-GO key is not detected while the engine is running
because there is interference fromastrongsource of radio waves.
Awarning tone also sounds.
XPull overand stop the vehiclesafelyassoonaspossible,paying
attention to road and traffic conditions.
XSecure the vehicle against rolling away(Ypage 167).
XOperate the vehicle with the SmartKey in the ignition lock.

Key Not Detected
(white display
message)
The KEYLESS-GO key cannot be detected at present.
XChange the location of the SmartKey with the KEYLESS-GO
functionsinthe vehicle.
If the KEYLESS-GO key is still not detected:
XOperate the vehicle with the SmartKey in the ignition lock.

Key Detected in
Vehicle
The KEYLESS-GO key has been detected inside the vehicle during
locking.
XRemove the KEYLESS-GO key from the vehicle.
Display messages263
On-board computer and displays
Z

Engine
ProblemPossible causes/consequences andSolutions
\n
The yellow Check
Enginewarning lamp
lightsupwhile the
engineisrunning.
Theremay beamalfunction, for example:
Rin theenginemanagement
Rin thefuel injection system
Rin theexhaust system
Rin theignition system
Rin thefuel system
The emission limit values may be exceeded and theenginemay
be runninginemergencymode.
XHavethevehicle checked as soon as possible ataqualified
specialist workshop.
iIn somestates, you must immediately visitaqualified
specialist workshopassoon as theyellow CheckEngine warning
lamp lights up.This is due to the legal requirements in effect in
these states. If in doubt, check whether such legal regulations
apply in the state in which you are currently driving.

The yellow reserve fuel
warning lamp lights up
while the engine is
running.
The fuel level has dropped into the reserve range.
XRefuel at the nearest gas station.

The yellow reserve fuel
warning lamp flashes
while the vehicle is in
motion.
In addition, the\n
Check Enginewarning
lamp may light up.
The fuel system pressure is too low. The fuel filler cap is not closed
correctly or the fuel system is leaking.
XCheck that the fuel filler cap is correctly closed.
XIf the fuel filler cap is not correctly closed:close the fuel filler
cap.
XIf the fuel filler cap is closed:visitaqualified specialist
workshop.

The red coolant
warning lamp lights up
while the engine is
running and the coolant
temperature gauge is
at the start of the scale.
The temperature sensor for the coolant temperature gauge is
defective.
The coolant temperature is no longer being monitored. There is a
risk of engine damage if the coolant temperature is too high.
XPull over and stop the vehicle safely and switch off the engine,
paying attention to road and traffic conditions. Do not continue
driving under any circumstances.
XSecure the vehicle against rolling away (Ypage 167).
XConsultaqualified specialist workshop.
Indicator and warning lampsinthe instrument cluster273
On-board computer and displays
Z

ProblemPossible causes/consequences andSolutions

The red coolant
warning lamp comes on
while the engine is
running.
The coolant level is too low.
If the coolant level is correct, the airflow to the engine radiator
may be blocked or the electric engine radiator fan may be
malfunctioning.
The coolant is too hot and the engine is no longer being cooled
sufficiently.
XObserve the additional display messages in the multifunction
display.
XPull over and stop the vehicle safely and switch off the engine,
paying attention to road and traffic conditions.
XSecure the vehicle against rolling away (Ypage 167).
XLeave the vehicle and keepasafe distance from the vehicle until
the engine has cooled down.
XCheck the coolant level and add coolant, observing the warning
notes (Ypage 308).
XIf you need to add coolant more often than usual, have the
engine coolant system checked.
XMake sure that the air supply to the engine radiator is not
blocked, e.g. by snow, slush or ice.
XDo not start the engine again until the coolant temperature is
under 248‡(120 †). Otherwise,the engine couldbedamaged.
XDrive to the nearest qualified specialist workshop.
XAvoid subjecting the engine to heavy loads, e.g. driving in
mountainousterrain, and stop-and-go traffic.

The red coolant
warning lamp comes on
while the engine is
running.Awarning tone
also sounds.
The coolant temperature has exceeded 248‡(120 †). The
airflow to the engine radiator may be blocked or the coolant level
may be too low.
GWARNING
The engine is not being cooledsufficiently and may be damaged.
Do not drive whenyour engine is overheated. This can cause some
fluids which may have leaked into the engine compartment to
catchfire.
Steam from the overheated engine can also cause serious burns
which can occur just by opening the hood.
There isarisk of injury.
XObserve the additional display messages in the multifunction
display.
XPull over and stop the vehicle safely and switch off the engine,
paying attention to road and traffic conditions.
XSecure the vehicle against rolling away (Ypage 167).
274Indicator and warning lampsinthe instrument cluster
On-board computer and displays

!Make sure that the windshieldwipers are
not folded away fromthe windshield. You
could otherwise damage the windshield
wipers or the hood.
XMake sure that the windshield wipers are
turned off.
XPull release leveron the hood.
The hood is released.
XReach into the gap, pull hood catch
handleup and lift the hood.
If you lift the hood by approximately
15 inches(40cm),the hood is opened and
held open automatically by the gas-filled
strut.
Closing thehood
XLower the hood and let it fall fromaheight
of approximately8inches(20 cm).
XCheck that the hood has engaged properly.
If the hood can be raised slightly,itisnot
properly engaged. Open it again and close
it withalittle more force.
Engine oil
General notes
Depending on the driving style, the vehicle
consumesupto0.9 US qt (0.8 liters) of oil
overadistanceof600 miles(1,000 km). The
oil consumption may be higher than this when
the vehicle is new or if you frequently drive at
high enginespeeds.
Depending on the engine, the oil dipstickmay
be inadifferent location.
When checking theoil level:
Rpark thevehicle onalevelsurface.
Rtheengineshould be switched off for
approximately fiveminutesiftheengineis
at normal operatingtemperature.
Rif theengineisnotat normal operating
temperature, e.g.ifthe engine was only
started briefly, wait about 30 minutes
before carrying out the measurement.
Checking the oil level using the oil
dipstick
XPull oil dipstickout of the dipstick guide
tube.
XWipe off oil dipstick.
XSlowly slide oil dipstickinto the guide
tube to the stop, and take it out again.
If the level is between MIN mark$and
MAX mark,the oil level is correct.
XIf the oil level has dropped to MIN mark
$or below, add 1.1 US qt (1.0 liter) of
engine oil.
Engine compartment307
Maintenance and care
Z

XPark the vehicle onalevel surface.
Only check the coolant level when the
vehicle is onalevel surface and the engine
has cooled down.
XTurn the SmartKey to position2in the
ignition lock (Ypage 147).
On vehicles with KEYLESS-GO, press the
Start/Stop button twice (Ypage 147).
XCheck the coolant temperature display in
the instrument cluster.
The coolant temperature must be below
158‡(70 †).
XTurn the SmartKey to position
0(Ypage 147) in the ignition lock.
XSlowly turn caphalfaturn counter-
clockwise to allow excess pressure to
escape.
XTurn capfurther counter-clockwise and
remove it.
If the coolant is at the level of marker bar
$in the filler neck when cold, there is
enough coolant in coolant expansion
tank.
If the coolant level is approximately 0.6 in
(1.5 cm) above marker bar$in the fuel
filler neck when warm, there is enough
coolant in expansion tank.
XIf necessary, add coolant that has been
tested and approved by Mercedes-Benz.
XReplace capand turn it clockwise as far
as it will go.
For further information on coolant,see
(Ypage 377).
Adding washer fluid to the windshield
washer system/headlampcleaning
system
GWARNING
Windshield washer concentrate is highly
flammable. If it comes intocontactwith hot
enginecomponentsorthe exhaust systemit
could ignite. There isariskoffire and injury.
Make sure that no windshield washer
concentrate is spilled nexttothe filler neck.
XTo open:pull capupwards by the tab.
XAdd the premixed washer fluid.
XTo close:press capontothe filler neck
until it engages.
The washer fluid reservoir is used for both the
windshield washer system and the headlamp
cleaning system.
If the washer fluid level drops below the
recommended minimum of1liter,amessage
appears in the multifunction display
promptingyou to refill the washer fluid
(Ypage 262).
Further information on windshield washer
fluid/antifreeze (Ypage 378).
Maintenance
ASSYST PLUS
Service messages
The ASSYSTPLUS service interval display
informsyou of the nextservice due date.
Maintenance309
Maintenance and care
Z

Do not remove the SmartKeyfromthe
ignition lock. Do not open the driver's
door or front-passengerdoor when the
engine is switched off. Otherwise, the
automatic transmission selects park
positionPautomatically and locks the
wheels. You can prevent this by shifting
the automatic transmission toN
beforehand.
RVehicles with KEYLESS-GO:
Do not open the driver's door or front-
passenger door when the engine is
switched off. Otherwise, the automatic
transmission selects park positionP
automatically and locks the wheels.
Observe the following to make sure that the
automatic transmission stays in positionN:
XMake sure the vehicle is stationary and the
ignition is switched off.
XTurn the SmartKey to position2in the
ignition lock (Ypage 147).
Use the SmartKey instead of the Start/
Stop button on vehicles with KEYLESS-GO.
XDepress and hold the brake pedal.
XShift the automatic transmission to
positionN.
XRelease the brake pedal.
XRelease the electric parking brake.
XSwitch off the ignition and leave the
SmartKey in the ignition lock.
You can wash the vehicle in an automatic car
wash from the very start.
If the vehicle is very dirty, pre-wash it before
cleaning it in an automatic car wash.
After using an automatic car wash, wipe off
wax from the windshield and the wiper
blades. This will prevent smears and reduce
wiping noises caused by residue on the
windshield.
Washing by hand
In some countries, washing by hand is only
allowedatspecially equipped washing bays.
Observe the legal requirements in all
countries concerned.
XDo not use hot water and do not wash the
vehicle in direct sunlight.
XUseasoft sponge to clean.
XUseamild cleaning agent, such asacar
shampoo approved by Mercedes-Benz.
XThoroughly hose down the vehicle with a
gentle jet of water.
XDo not point the water jet directly towards
the air inlet.
XUse plenty of water and rinse out the
sponge frequently.
XRinse the vehicle with clean water and dry
thoroughly withachamois.
XDo not let the cleaning agent dry on the
paintwork.
When using the vehicle in winter, remove all
traces of road salt deposits carefully and as
soon as possible.
Power washers
GWARNING
The water jet fromacircular jet nozzle (dirt
blasters) can cause invisible exterior damage
to the tires or chassis components.
Componentsdamaged in this way may fail
unexpectedly. There isarisk of an accident.
Do not use power washers with circular jet
nozzles to clean the vehicle. Have damaged
tires or chassis components replaced
immediately.
!Always maintainadistance of at least
11.8in(30 cm) between the vehicleand the
powerwasher nozzle. Information about
thecorrectdistanceisavailablefromthe
equipmentmanufacturer.
Movethepower washernozzle around
when cleaning your vehicle.
Do not aim directly at any of the following:
Rtires
Rdoor gaps, roof gaps, joints, etc.
Relectrical components
312Care
Maintenance and care

Alignment bolt
%Sheet for faulty wheel
Tire inflation compressor
Lugwrench
Fuseallocation chart
XOpenthe trunk lid.
XLift the trunk floor upwards (Ypage 283).
Flat tire
Preparing the vehicle
Your vehicle may be equipped with:
RMOExtended tires (tires with run-flat
properties) (Ypage 321)
Vehicle preparation is not necessary on
vehicles with MOExtended tires.
Ran emergency spare wheel(Ypage 367)
Information on changing/mountingawheel
(Ypage 357).
XStop the vehicle on solid, non-slippery and
level ground, as far away as possible from
traffic.
XSwitch on the hazard warning lamps.
XSecure the vehicle against rolling away
(Ypage 167).
XIf possible, bring the front wheels into the
straight-ahead position.
XVehicles with AIRMATIC: make sure that
"normal" level is selected (Ypage 189).
XSwitch off the engine.
XVehicles without KEYLESS-GO:remove
the SmartKey from the ignition lock.
XVehicles with KEYLESS-GO:open the
driver's door.
The on-board electronicsnow have status
0.This is the same as the SmartKey having
been removed.
XVehicles with KEYLESS-GO:remove the
Start/Stop button from the ignition lock
(Ypage 147).
XAll occupants must get out of the vehicle.
Make sure that they are not endangered as
they do so.
XMake sure that no one is near the danger
area whileawheel is being changed.
Anyone who is not directly assisting in the
wheel change should, for example, stand
behind the barrier.
XGet out of the vehicle. Pay attention to
traffic conditionswhen doing so.
XClose the driver's door.
MOExtended tires (tires with run-flat
properties)
General notes
With MOExtended tires (tires with run flat
characteristics), you can continue to drive
your vehicle even if there isatotal loss of
pressure in one or more tires. The affected
tire must not show any clearly visible damage.
You can recognizeMOExtended tires by the
MOExtended marking which appears on the
sidewall of the tire. You will find this marking
next to the tire size designation, the load-
bearing capacity and the speed index
(Ypage 351).
MOExtended tires may only be used in
conjunction with an active tire pressure loss
warning system or with an active tire pressure
monitor.
If the pressureloss warning message
appearsinthe multifunction display:
RObserve the instructions in the display
messages (Ypage 258).
RCheck the tire for damage.
RIf driving on, observe the following notes.
The maximum driving distance is
approximately 50 miles (80 km) when the
vehicle is partially laden and approximately
18 miles (30 km) when the vehicle is fully
laden.
Flat tire321
Breakdown assistance

In addition to the vehicle load, the driving
distance possible depends upon:
RSpeed
RRoadcondition
ROutside temperature
The driving distance possible in run-flat mode
may be reduced by extreme driving
conditions/maneuvers, or it can be increased
throughamoderate style of driving.
The maximum permissible distance which
can be driven in run-flat mode is counted from
the moment the tire pressure loss warning
appears in the multifunction display.
You must not exceedamaximum speed of
50 mph (80 km/h).
iWhen replacing one or all tires, make sure
that you use only tires:
Rof the size specified for the vehicle and
Rmarked "MOExtended"
Ifatire has gone flat and cannot be
replaced withaMOExtended tire, a
standard tire may be used asatemporary
measure. Make sure that you use the
proper size and type (summerorwinter
tire).
Important safety notes
GWARNING
When drivinginemergencymode, the driving
characteristics deteriorate, e.g. when
cornering, accelerating quickly and when
braking. There isarisk of an accident.
Do not exceed the stated maximum speed.
Avoid abrupt steeringand drivingmaneuvers,
and drivingover obstacles (curbs, potholes,
off-road). This applies in particular toaladen
vehicle.
Stop drivinginemergencymode if:
Ryou hear bangingnoises.
Rthe vehicle starts to shake.
Ryou see smokeand smell rubber.
RESP®is interveningconstantly.
Rthere are tearsinthe sidewalls of the tire.
After drivinginemergency mode, have the
wheel rims checked ataqualified specialist
workshop with regardtotheir further use. The
defectivetiremust be replaced in everycase.
Battery (vehicle)
Important safety notes
Special tools and expert knowledge are
requiredwhen working on the battery, e.g.
removal and installing. You should therefore
have all work involvingthe battery carried out
ataqualified specialist workshop.
GWARNING
Work carried out incorrectly on the battery
can lead, for example, toashortcircuit and
thus damage the vehicle electronics. This can
lead to function restrictionsapplying to
safety-relevantsystems,e.g.thelighting
system, ABS(anti-lockbrakingsystem) or
ESP®(Electronic StabilityProgram). The
operating safetyofyour vehiclemay be
restricted. You could lose control of the
vehicle, for example:
Rbraking
Rin theevent of abruptsteeringmaneuver
and/orwhen the vehicle's speed is not
adapted to the road conditions
There isarisk of an accident.
In the event ofashort circuit orasimilar
incident, contactaqualified specialist
workshop immediately. Do not drive any
further. You should have all work involving the
battery carried out ataqualifiedspecialist
workshop.
GWARNING
Electrostatic build-up can lead to thecreation
of sparks,whichcould ignite thehighly
explosive gases ofabattery. Thereisariskof
an explosion.
322Battery (vehicle)
Breakdown assistance

XFirst, remove the jumper cablesfrom earth pointand negative terminal!,then from
positiveclampand positiveterminal$.Begineachtime at the contacts on your own
vehicle first.
XClose coverof positiveclampafterremoving the jumper cables.
XHave the battery checkedataqualified specialist workshop.
iJump-startingisnot considered to beanormal operatingcondition.
iJumper cables and further information regardingjump-starting can be obtained at any
qualified specialist workshop.
Towing and tow-starting
Importantsafetynotes
GWARNING
Functionsrelevant to safety are restricted or
no longer available if:
Rthe engineisnot running.
Rthe brake system or the power steering is
malfunctioning.
Rthereisamalfunction in the voltage supply
or the vehicle's electrical system.
If your vehicle is being towed, much more
forcemay be necessary to steer or brake.
There isarisk of an accident.
In such cases, useatow bar. Beforetowing,
make sure that the steering moves freely.
GWARNING
If the weight of the vehicle to be towed or tow-
started is greater than the permissible gross
weight of your vehicle:
Rthe towingeye could detach itself
Rthe vehicle/trailer combination could
rollover.
There isarisk of an accident.
When towingortow-starting another vehicle,
its weight should not be greater than the
permissible gross weight of your vehicle.
Information on your vehicle's gross vehicle
weight ratingcan be found on the vehicle
identification plate (Ypage 372).
!If DISTRONIC PLUS or the HOLD function
is activated, the vehicle brakes
automatically in certain situations. To
preventdamage to thevehicle,deactivate
DISTRONICPLUS and the HOLD function in
the following or other similar situations:
Rwhen towing the vehicle
Rin the car wash
!Only secure the tow rope or tow bar at the
towing eyes. Otherwise,the vehicle could
be damaged.
!Do not use the towing eye for recovery,
this could damage the vehicle.Ifindoubt,
recover the vehicle withacrane.
!When towing, pullawayslowly and
smoothly.Ifthe tractive power is too high,
the vehicles could be damaged.
!Do not tow with sling-type equipment.
This could damage the vehicle.
!When towing vehicles with KEYLESS-GO,
use the key instead of the Start/Stop
button. Otherwise, the automatic
transmission may shift to positionPwhen
the driver's or front-passenger door are
opened, which could lead to damage to the
transmission.
!The vehicle can be towedamaximum of
30 miles (50km). The towing speed of
30 mph (50 km/h) must not be exceeded.
If the vehicle has to be towed more than
30 miles(50km), the entire vehicle must be
raised and transported.
328Towing and tow-starting
Breakdown assistance