battery MERCEDES-BENZ E350 2006 W211 User Guide
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2006, Model line: E350, Model: MERCEDES-BENZ E350 2006 W211Pages: 521
Page 117 of 521
116 Controls in detailLocking and unlockingGlobal locking
Press lock button on an outside door
handle (
page 64) or lock button at
trunk lid (page 117).
All turn signal lamps flash three
times.
An acoustic signal sounds three
times (if equipped and feature acti-
vated).
The locking knobs in the doors
move down.
The anti-theft alarm system is
armed.
Restoring to factory setting
Press and hold buttonsŒ and‹
simultaneously for about 6 seconds un-
til battery check lamp5 (
page 111)
flashes twice.Checking the batteries
Press button‹ orŒ.
Battery check lamp5 (
page 111)
comes on briefly to indicate that the
SmartKey batteries are in order.
!If you can no longer lock or unlock the
vehicle with the SmartKey with
KEYLESS-GO, then the batteries in the
SmartKey are discharged, the
SmartKey with KEYLESS-GO is mal-
functioning or the vehicle battery is
drained.
Check the batteries in the
SmartKey with KEYLESS-GO
(page 116) and replace them if
necessary (
page 431).
Use the mechanical key to unlock
the driver’s door (
page 426) and
the trunk (
page 427).
Use the mechanical key to lock the
driver’s door (
page 426) and the
trunk (
page 128).
Have the vehicle battery checked
by an authorized Mercedes-Benz
Center.
If the SmartKey with KEYLESS-GO is
malfunctioning, contact an authorized
Mercedes-Benz Center.
!If battery check lamp5 does not
come on briefly during check, then the
SmartKey batteries are discharged.
Replace the batteries (
page 431).
You can obtain the required batteries
at any authorized Mercedes-Benz
Center.
iIf the batteries are checked within sig-
nal range of the vehicle, pressing the
button‹ orŒ will lock or unlock
the vehicle accordingly.
Page 148 of 521
147 Controls in detail
Lighting
Interior lighting in the front
1Left front reading lamp on/off
2Rear interior lighting on/off
3Automatic control on/off
4Front interior lighting on/off
5Right front reading lamp on/off
6Ambient lighting
7Interior lighting
8Front reading lampsThe controls are located in the overhead
control panel.
Automatic control
Activating
Press automatic control switch3.
The interior lighting switches on in
darkness when you:
unlock the vehicle
remove the SmartKey from the
starter switch
open a door
open the trunk
The interior lighting switches off automati-
cally following an adjustable time delay.For more information, see “Setting interior
lighting delayed shut-off” (
page 173).
Deactivating
Press automatic control switch3
again.
The interior lighting remains switched
off in darkness, even when you:
unlock the vehicle
remove the SmartKey from the
starter switch
open a door
open the trunk
iLeaving an interior light switch in the
ON position for extended periods of
time with the engine turned off could
result in a discharged battery.
iIf the door remains open, the interior
lighting switches off automatically after
approximately 5 minutes.
Page 202 of 521
201 Controls in detail
Good visibility
Roller sunblind* in the rear doors
Pull the roller sunblind out using the
hooks.
Attach the hooks at the top.
Rear window defroster
The rear window defroster uses a large
amount of power. To keep the battery
drain to a minimum, switch off the defrost-
er as soon as the rear window is clear. The
defroster is automatically deactivated af-
ter approximately 6 to 17 minutes of oper-
ation depending on the outside
temperature.
Activating
Press button1 (
page 204) or
(
page 216) orF (
page 217) on
the respective climate control panel.
The indicator lamp on the button
comes on.Deactivating
Press buttonF or1 again.
The indicator lamp on the button goes
out.
!Always guide the sunblind by hand. Do
not let it snap back, as the retractor
could be damaged.
Warning!
G
Any accumulation of snow and ice should be
removed from the rear window before driv-
ing. Visibility could otherwise be impaired,
endangering you and others.!If the rear window defroster switches
off too soon and the indicator lamp
starts flashing, this means that too
many electrical consumers are operat-
ing simultaneously and there is insuffi-
cient voltage in the battery. The system
responds automatically by deactivating
the rear window defroster.
As soon as the battery has sufficient
voltage, the rear window defroster au-
tomatically turns itself back on.
Page 229 of 521
228 Controls in detail4-zone automatic climate control*Residual heat and ventilation (Canada only)
With the engine switched off, it is possible
to continue to heat or ventilate the interior
for up to 30 minutes. This feature makes
use of the residual heat produced by the
engine.
Activating
Switch off the ignition.
Press buttonT (
page 217).
REST in the display4 (page 217)
comes on.Deactivating
Press buttonT (
page 217) again.
REST in the display4 (page 217)
goes out.
iIf you switch on the residual heat
function when temperatures are high,
only the ventilation will be switched on.iRegardless of the selected air volume,
the blower operates at low speed.
iHow long the system will provide heat-
ing depends on
the coolant temperature
the temperature set by the operator
The blower will run at speed setting1
regardless of the air distribution
control setting.
iThe residual heat is automatically
turned off:
when the ignition is switched on
after about 30 minutes
if the battery voltage drops
if the coolant temperature is too
low
Page 234 of 521
233 Controls in detail
Power windows
Fully closing the windows
(Express-close)
Pull switch2 to 5 past the resis-
tance point and release.
The corresponding window closes com-
pletely.
Stopping windows during Express-op-
eration
Press or pull the respective power win-
dow switch again.
Synchronizing power windows
The power windows must be synchronized
after the battery has been disconnect-
ed
if the power windows cannot be fully
opened (Express-open) or closed
(Express-close)
Synchronizing
Close all doors.
Switch on the ignition (
page 36).
Pull switch2 to 5 until the side win-
dows are completely closed.
Hold on to switches2 to 5 for ap-
proximately 1 second.
The power windows are synchronized.
Warning!
G
Driver’s door only:
If within 5 seconds switch is again pulled
past the resistance point and released, the
automatic reversal will not operate.
!If the upward movement of the window
is blocked during the closing proce-
dure, the window will stop and open
slightly.
Remove the obstruction, pull the re-
spective power window switch again
past the resistance point and release.
If the window still does not close when
there is no obstruction, pull and hold
the respective power window switch.
The side window will then close without
the obstruction sensor function.
Page 239 of 521
238 Controls in detailPower tilt/sliding sunroof*Stopping the power tilt/sliding sunroof
during Express-operation
Move the sunroof switch in any direc-
tion.Synchronizing the power tilt/sliding
sunroof
The tilt/sliding sunroof must be synchro-
nized
after the battery has been
disconnected or discharged
after the tilt/sliding sunroof has been
closed manually (
page 429)
after a malfunction
if the tilt/sliding sunroof does not open
smoothly
Remove the respective fuse from the
main fuse box (
page 461).
Reinsert the fuse in the main fuse box.
Switch on the ignition (
page 36).
Move and hold the sunroof switch in di-
rection of arrow3 until the tilt/sliding
sunroof is fully raised at the rear.
Keep holding the sunroof switch in di-
rection of arrow3 for approximately
1 second.
Check the Express-open feature
(page 237).
If the tilt/sliding sunroof opens com-
pletely, the roof is synchronized. Other-
wise repeat the above steps.
iIf the movement of the tilt/sliding sun-
roof is blocked during the
Express-close procedure, the tilt/slid-
ing sunroof will stop and reopen
slightly.
Page 243 of 521
242 Controls in detailPanorama roof with power tilt/sliding panel*Synchronizing the panorama roof with power tilt/sliding panel
The tilt/sliding panel must be
synchronized
after the battery has been
disconnected or discharged
after the tilt/sliding panel has been
closed manually (
page 429)
after a malfunction
if the tilt/sliding panel does not open
smoothly
Remove the fuse from the main fuse
box (
page 461).
Reinsert the fuse in the main fuse box.
Switch on the ignition (
page 36).
Move and hold the roof panel switch in
direction of arrow2 until the roller
sunblinds are fully closed.
Keep holding the roof panel switch in
direction of arrow2 for approximately
1 second.
Move and hold the roof panel switch in
direction of arrow1 until the roller
sunblinds are fully opened.
Keep holding the roof panel switch in
direction of arrow1 for approximately
1 second.
Move and hold the roof panel switch in
direction of arrow3 until the tilt/slid-
ing panel is fully raised.
Keep holding the roof panel switch in
direction of arrow3 for approximately
1 second.
Move and hold the roof panel switch in
direction of arrow2 until the tilt/slid-
ing panel is fully closed.
Keep holding the roof panel switch in
direction of arrow2 for approximately
1 second.
Check the Express-open feature of the
tilt/sliding panel (
page 241).
If the tilt/sliding panel opens com-
pletely, the roof is synchronized. Other-
wise repeat the above steps.
Page 287 of 521
286 Controls in detailUseful featuresTele Aid
Shortly after the completion of your
Tele Aid acquaintance call, you will receive
a user ID and password. By visiting
www.mbusa.com and selecting “Tele Aid”
(USA only), you will have access to account
information, remote door unlock and
more.The Tele Aid system
(Tele
matic A
larm I
dentification on D
e-
mand)
The Tele Aid system consists of three
types of response:
automatic and manual emergency
Roadside Assistance and
information
The Tele Aid system is operational provid-
ing that the vehicle’s battery is charged,
properly connected, not damaged and cel-
lular and GPS coverage is available.
The speaker volume of a Tele Aid call can
be adjusted when using the volume control
on the multifunction steering wheel. To
raise, press buttonæ and to lower,
press buttonç or use the volume knob
on your COMAND headunit.
To activate, press the SOS button, the
Roadside Assistance button• or
the Information button¡, depend-
ing on the type of response required.System self-check
Initially, after switching on the ignition,
malfunctions are detected and indicated
(the indicator lamps in the SOS button, the
Roadside Assistance button• and the
Information button¡ stay on longer
!The initial activation of the Tele Aid sys-
tem may only be performed by com-
pleting the subscriber agreement and
placing an acquaintance call using
button¡. Failure to complete either
of these steps will result in a system
that is not activated.
If you have any questions regarding ac-
tivation, please call the Response Cen-
ter at 1-800-756-9018 (in the USA) or
1-888-923-8367 (in Canada).
iThe SOS button is located above the in-
terior rear view mirror.
The Roadside Assistance button•
and the Information button¡ are
located below the center armrest cov-
er.iThe Tele Aid system utilizes the cellular
network for communication and the
GPS (G
lobal P
ositioning S
ystem) satel-
lites for vehicle location. If either of
these signals are unavailable, the
Tele Aid system may not function and if
this occurs, assistance must be sum-
moned by other means.
Page 300 of 521
299 Controls in detail
Useful features
Erasing the integrated remote control
memory
Switch on the ignition (
page 36).
Simultaneously press and hold down
the outer signal transmitter buttons2
and 4, for approximately 20 seconds,
until the indicator lamp1 flashes rap-
idly. Do not hold for longer than
30 seconds.
The codes of all three channels are
erased.Programming tips
If you are having difficulty programming
the integrated remote control, here are
some helpful tips:
Check the frequency of the hand-held
remote control5 (typically located on
the reverse side of the remote). The in-
tegrated remote control is compatible
with radio-frequency devices operating
between 288-399 MHz.
Put a new battery in the hand-held re-
mote control5. This will increase the
likelihood of the hand-held remote con-
trol sending a faster and more accurate
signal to the integrated remote control.
While performing step 3, hold the
hand-held remote control6 at differ-
ent lengths and angles from the signal
transmitter button (2, 3 or4) you
are programming. Attempt varying an-
gles at the distance of 2 to 5 inches
(5 to 12 cm) away or the same angle at
varying distances.
If another hand-held remote control is
available for the same device, try the
programming steps again using that
other hand-held remote control. Make
sure new batteries are in the hand-held
remote control before beginning the
procedure.
Straighten the antenna wire from the
garage door opener assembly. This
may help improve transmitting and/or
receiving signals.
iIf you sell your vehicle, erase the codes
of all three channels.
iCertain types of garage door openers
are incompatible with the integrated
remote control. If you should experi-
ence further difficulties with program-
ming the integrated remote control,
contact an authorized Mercedes-Benz
Center, or call Mercedes-Benz
Customer Assistance Center (in the
USA only) at 1-800-FOR-MERCedes, or
Customer Service (in Canada) at
1-800-387-0100.
Page 327 of 521
326 OperationEngine compartmentBatteries
Your vehicle is equipped with two
batteries:
Main battery (located in the trunk).
Auxiliary battery (located in the engine
compartment).
These batteries should always be suffi-
ciently charged in order to achieve their
rated service life. Refer to Maintenance
Booklet for battery maintenance intervals.
If you use your vehicle mostly for short-dis-
tance trips, you will need to have the bat-
tery charge checked more frequently.
When replacing batteries, always use bat-
teries approved by Mercedes-Benz.
If you do not intend to operate your vehicle
for an extended period of time, consult an
authorized Mercedes-Benz Center about
steps you need to observe.Batteries contain materials that can harm
the environment if disposed of improperly.
Recycling of batteries is the preferred
method of disposal. Many states require
sellers of batteries to accept old batteries
for recycling.
G
Observe all safety instructions
and precautions when handling
automotive batteries.
A
Risk of explosion
D
Keep flames or sparks away
from battery. Do not smoke.
B
Battery acid is caustic. Do not
allow it to come into contact
with skin, eyes or clothing.
In case it does, immediately
flush affected area with clean
water and seek medical help if
necessary.
E
Wear eye protection.
C
Keep children away.
F
Follow the instructions in this
Operator’s Manual.