antifreeze MERCEDES-BENZ GL320 2008 X164 Owner's Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2008, Model line: GL320, Model: MERCEDES-BENZ GL320 2008 X164Pages: 601
Page 382 of 601
381 Operation
Engine compartment
Adding engine oil
Example illustration GL 450 (GL 320 CDI,
GL 550 similar)
1Filler cap
Unscrew filler cap1 from filler neck.
Add engine oil as required. Never over-
fill with oil.
Be careful not to spill any oil when adding.
Avoid environmental damage caused by oil
entering the ground or water.
Screw filler cap1 back on filler neck.
For more information on engine oil, see
“Technical data” section (
page 562) and
(
page 564).
Transmission fluid level
The transmission fluid level does not need
to be checked. If you notice transmission
fluid loss or gear shifting malfunctions,
have an authorized Mercedes-Benz Light
Truck Center check the automatic trans-
mission.
Coolant level
The engine coolant is a mixture of water
and anticorrosion/antifreeze.
When checking the coolant level
the vehicle must be parked on level
ground
the coolant temperature must be below
158°F (70°C)
!Only use approved engine oils and oil filters
required for vehicles with Maintenance System.
For a listing of approved engine oils and oil
filters, refer to the Factory Approved Service
Products pamphlet (USA only) in your vehicle
literature portfolio, or contact an authorized
Mercedes-Benz Light Truck Center.
Using engine oils and oil filters of specification
other than those expressly required for the
Maintenance System, or changing of oil and oil
filter at change intervals longer than those called
for by the Maintenance System will result in
engine or emission control system damage not
covered by the Mercedes-Benz Limited
Warranty.
!Excess oil must be siphoned or drained off.
It could cause damage to the engine and/or
catalytic converter (gasoline engine) or the oxi-
dation catalyst (diesel engine) not covered by
the Mercedes-Benz Limited Warranty.
164.boo Seite 381 Freitag, 30. März 2007 12:54 12
Page 383 of 601
382 Operation
Engine compartment
The coolant expansion tank is located on
the driver’s side of the engine compart-
ment.
1Cap
2Coolant expansion tank
3Indicator wall
4Coolant levelUsing a rag, turn cap1 slowly approx-
imately one half turn counterclockwise
to release any excess pressure.
Continue turning cap1 counterclock-
wise and remove it.
Coolant level4 is correct if the level:
for cold coolant: reaches the top of
indicator wall3 visible through the
filling opening
for warm coolant: is approximately
0.6 in (1.5 cm) higher
Add coolant as required.
Replace and tighten cap1.
For more information on coolant, see
“Coolants” (
page 567).
Warning!G
In order to avoid potentially serious burns:
Use extreme caution when opening the
hood if there are any signs of steam or
coolant leaking from the cooling system,
or if the coolant temperature display
indicates that the coolant is overheated.
Do not remove pressure cap on coolant
reservoir if coolant temperature is
above 158°F (70°C). Allow engine to
cool down before removing cap. The
coolant reservoir contains hot fluid and
is under pressure.
Using a rag, slowly open the cap approx-
imately 1/2 turn to relieve excess pres-
sure. If opened immediately, scalding
hot fluid and steam will be blown out
under pressure.
Do not spill antifreeze on hot engine
parts. Antifreeze contains ethylene
glycol which may burn if it comes into
contact with hot engine parts.
164.boo Seite 382 Freitag, 30. März 2007 12:54 12
Page 384 of 601
383 Operation
Engine compartment
Windshield/rear window washer
system and headlamp cleaning
system*
The windshield washer reservoir is located
in the engine compartment.
1Cap for windshield washer reservoir
Fluid for the windshield/rear window
washer system and the headlamp cleaning
system* is supplied from the windshield
washer reservoir. It has a capacity of 8.1
US qt (7.7 l).During all seasons, add MB Windshield
Washer Concentrate “MB SummerFit” to
water. Premix the windshield washer fluid
in a suitable container.
Use the tab to pull cap1 upwards.
Refill the reservoir with MB Windshield
Washer Concentrate “MB SummerFit”
and water (or commercially available
premixed windshield washer sol-
vent/antifreeze, depending on ambient
temperatures).For more information, see “Windshield
washer system and headlamp cleaning
system*” (
page 569).Warning!G
Washer solvent/antifreeze is highly flamma-
ble. Do not spill washer solvent/antifreeze
on hot engine parts, because it may ignite
and burn. You could be seriously burned.
!Always use washer solvent/antifreeze
where temperatures may fall below freezing
point. Failure to do so could result in damage to
the washer system/reservoir.
!Only use washer fluid which is suitable for
plastic lenses. Improper washer fluid can
damage the plastic lenses of the headlamps.
164.boo Seite 383 Freitag, 30. März 2007 12:54 12
Page 421 of 601
420 Operation
Winter driving
Before the onset of winter, have your
vehicle winterized at an authorized
Mercedes-Benz Light Truck Center. This
service includes:
Check of anticorrosion and antifreeze
concentration.
Addition of cleaning concentrate to the
water of the windshield and headlamp
cleaning system. Add MB Concentrate
“MB SummerFit” to a premixed wind-
shield washer solvent/antifreeze
which is formulated for temperatures
below freezing point (
page 569).
Battery test. Battery capacity drops
with decreasing ambient temperature.
A well charged battery helps to make
sure that the engine can be started
even at low ambient temperatures.
Tire change. Mercedes-Benz recom-
mends M+S rated radial-ply tires with a
minimum tread depth of approximately
1/6in (4 mm) on all four wheels for the
winter season.
Winter tires
Always use winter tires at temperatures
below 45°F (7°C) and whenever wintry
road conditions prevail. Not all M+S rated
tires provide special winter performance.
Make sure the tires you use show the
mountain/snowflake.marking on the
tire sidewall. These tires meet specific
snow traction performance requirements
of the Rubber Manufacturers Association
(RMA) and The Rubber Association of Can-
ada (RAC) and have been designed specif-
ically for use in snow conditions. Use of
winter tires is the only way to achieve the
maximum effectiveness of the ABS, ESP
®,
4-ETS, and EBP in winter operation.
For safe handling, make sure all mounted
winter tires are of the same make and have
the same tread design.Always observe the speed rating of the
winter tires installed on your vehicle. If the
maximum speed for which your tires are
rated is below the speed rating of your
vehicle, you must place a notice to this
effect where it will be seen by the driver.
Such notices are available from your tire
dealer or from any authorized
Mercedes-Benz Light Truck Center.
Warning!G
Winter tires with a tread depth of less than 1/6in (4 mm) must be replaced. They are no
longer suitable for winter operation.
164.boo Seite 420 Freitag, 30. März 2007 12:54 12
Page 473 of 601
472 Practical hints
What to do if …
Display symbolDisplay messagePossible cause/consequencePossible solution
B Top Up Coolant
See Operator’s ManualThe coolant level is too low.Add coolant (page 381).
If you have to add coolant frequently,
have the cooling system checked by an
authorized Mercedes-Benz Light Truck
Center.
Warning!G
Do not spill antifreeze on hot engine parts.
Antifreeze contains ethylene glycol which
may burn if it comes into contact with hot
engine parts. You could be seriously burned.
!Do not ignore the low engine coolant level
warning. Extended driving with the message and
symbol displayed may cause serious engine
damage not covered by the Mercedes-Benz
Limited Warranty.
Do not drive without sufficient amount of coolant
in the cooling system. The engine will overheat
causing major engine damage.
164.boo Seite 472 Freitag, 30. März 2007 12:54 12
Page 564 of 601
563 Technical data
Fuels, coolants, lubricants
ModelCapacityFuels, coolants, lubricants, etc.
Front wheel hubsAll modelsapprox. 1.5oz (43g) eachHigh temperature roller bearing grease
Brake systemAll models-MB Brake Fluid (DOT 4+)
Cooling systemGL 320 CDIapprox. 10.0 US qt (9.5 l)MB Anticorrosion/Antifreeze
GL 450approx. 10.6 US qt (10.0 l)MB Anticorrosion/Antifreeze
GL 5501approx. 12.7 US qt (12.0 l)MB Anticorrosion/Antifreeze
Fuel Tank
including a reserve ofAll models26.4 US gal (100.0 l)
approx. 3.4 US gal (13.0 l)Gasoline engine:
Premium unleaded gasoline:
Minimum Posted Octane 91
(Avg. of 96 RON/86 MON)
Diesel engine:
ULTRA-LOW SULFUR HIGHWAY DIESEL FUEL
(15 ppm SULFUR MAXIMUM)
Air conditioning systemAll models-R-134a refrigerant and special PAG lubricant oil
(never R-12)
Windshield washer system
and headlamp cleaning
system*All models8.1 US qt (7.7 l)MB Windshield Washer Concentrate2
1Data preliminary.2Use MB Windshield Washer Concentrate “MB SummerFit” and water for temperatures above freezing or MB Windshield Washer Concentrate “MB SummerFit” and
commercially available premixed windshield washer solvent/antifreeze for temperatures below freezing. Follow suggested mixing ratios (page 569).
164.boo Seite 563 Freitag, 30. März 2007 12:54 12
Page 568 of 601
567 Technical data
Fuels, coolants, lubricants
Coolants
The engine coolant is a mixture of water
and anticorrosion/antifreeze, which
provides:
Corrosion protection
Freeze protection
Boiling protection (by increasing the
boiling point)
The cooling system was filled at the factory
with a coolant providing freeze protection
to approximately -35°F (-37°C) and corro-
sion protection.If the antifreeze mixture is effective to
-35°F (-37°C), the boiling point of the cool-
ant in the pressurized cooling system is
reached at approximately 266°F (130°C).
The coolant solution must be used year
round to provide the necessary corrosion
protection and increase boil-over protec-
tion. Refer to Maintenance Booklet for
replacement interval.
Coolant system design and coolant used
determine the replacement interval. The
replacement interval published in the
Maintenance booklet is only applicable if
MB 325.0 Anticorrosion/Antifreeze solu-
tion or other Mercedes-Benz approved
products of equal specification are used to
renew the coolant concentration or bring it
back up to the proper level.
For information on other Mercedes-Benz
approved products of equal specification,
refer to the Factory Approved Service
Products pamphlet (USA only) or contact
an authorized Mercedes-Benz Light Truck
Center.To provide important corrosion protection,
the solution must be at least 50% anticor-
rosion/antifreeze (equivalent to freeze
protection to approximately -35°F
[-37°C]). If you use a solution that is more
than 55% anticorrosion/antifreeze (freeze
protection to approximately -49°F
[-45°C]), the engine temperature will
increase due to the lower heat transfer
capability of the solution. Therefore, do not
use more than this amount of anticorro-
sion/antifreeze.
If the coolant level is low, water and
MB 325.0 Anticorrosion/Antifreeze
should be used to bring it up to the proper
level (have cooling system checked for
signs of leakage). Please make sure the
mixture is in accordance with label instruc-
tions.
The water in the cooling system must meet
minimum requirements, which are usually
satisfied by normal drinking water. If you
are not sure about the water quality, con-
sult an authorized Mercedes-Benz Light
Truck Center.
!Add premixed coolant solution only. Adding
water and MB 325.0 Anticorrosion/Antifreeze
separately from each other, could cause engine
damage not covered by the
Mercedes-Benz Limited Warranty.
164.boo Seite 567 Freitag, 30. März 2007 12:54 12
Page 569 of 601
568 Technical data
Fuels, coolants, lubricants
Anticorrosion/antifreeze
Your vehicle contains a number of
aluminum parts. The use of aluminum
components in motor vehicle engines
necessitates that anticorrosion/antifreeze
coolant used in such engines be
specifically formulated to protect the aluminum parts. Failure to use such
anticorrosion/antifreeze coolant will result
in a significantly shortened service life.
Therefore, the following product is strongly
recommended for use in your vehicle:
MB 325.0 Anticorrosion/Antifreeze agent.Before the start of the winter season (or
once a year in hot southern regions), you
should have the anticorrosion/antifreeze
concentration checked. The coolant is also
regularly checked each time you bring your
vehicle to an authorized Mercedes-Benz
Light Truck Center for service.
Anticorrosion/antifreeze quantity
Approximate freeze protection
Model-35°F (-37°C)-49°F (-45°C)
GL 320 CDI5.0 US qt (4.75 l)5.5 US qt (5.2 l)
GL 4505.3 US qt (5.0 l)5.8 US qt (5.5 l)
GL 5501
1Data preliminary.
5.6 US qt (5.25 l)6.1 US qt (5.8 l)
164.boo Seite 568 Freitag, 30. März 2007 12:54 12
Page 570 of 601
569 Technical data
Fuels, coolants, lubricants
Windshield washer system and
headlamp cleaning system*
Both the windshield washer system and
headlamp cleaning system* are supplied
from the windshield washer reservoir.
The windshield washer reservoir has a ca-
pacity of approximately 8.1 US qt (7.7 l).
Refill the reservoir with MB Windshield
Washer Concentrate and water (or con-
centrate and commercially available
premixed windshield washer sol-
vent/antifreeze, depending on ambient
temperatures).Windshield and headlamp washer fluid
mixing ration
For temperatures above freezing point, use
MB Windshield Washer Concentrate
“MB SummerFit” and water:
1 part “MB SummerFit” to 100 parts
water
(1.34 fl oz [40 ml] “MB SummerFit” to
1gal [4.0l] water)
For temperatures below freezing point, use
MB Windshield Washer Concentrate
“MB SummerFit ” and commercially avail-
able premixed windshield washer
solvent/antifreeze:
1 part “MB SummerFit” to 100 parts
solvent
(1.34 fl oz [40 ml] “MB SummerFit” to
1 gal [4.0 l] solvent)Warning!G
Washer solvent/antifreeze is highly flamma-
ble. Do not spill washer solvent/antifreeze
on hot engine parts, because it may ignite
and burn. You could be seriously burned.
164.boo Seite 569 Freitag, 30. März 2007 12:54 12
Page 572 of 601
571 Index
A
ABS 101
Indicator lamp 436
Off-road - ABS 102
ABS, ESP
®
Messages in the multifunction
display 451
Accelerator position, automatic
transmission 195
Accessory weight 415
Accident 66
Active head restraint 90, 133, 499
Adaptive Damping System (ADS)* 278
Air bags 76
Children 77, 91
Front passenger front air bag off
indicator lamp 31, 32, 85
Front, Driver 79
Front, Passenger 79
Occupant Classification System
(OCS) 81
Safety guidelines 78
Side impact (front and rear*) 80
Window curtain 80Air conditioning refrigerant 564
Air conditioning system see
Climate control or
Automatic climate control (3-zone)*
Air conditioning, Cooling 224, 239
Air distribution, Front 219, 234
Air distribution, Rear 227, 243
Air pressure see Tire inflation pressure
Air recirculation mode 222, 237
Air suspension program 278
Adaptive Damping System
(ADS)* 278
Messages in the multifunction
display 486
Vehicle level control 279
Air vents 227
Air vents*, Rear 245
Air vents, Front 220, 234
Air volume 220, 235
Alarm system see Anti-theft systems
Alignment bolt (vehicle tool kit) 492, 524
Anticorrosion/antifreeze 563, 568
Antiglare, Interior rear view mirror 208Antiglare, Rear view mirrors* 208
Antilock Brake System see ABS
Anti-theft systems 110
Anti-theft alarm system 109, 110
Immobilizer 109
Aquaplaning see Hydroplaning
Armrest storage/telephone*
compartment
Front 317
Ashtrays (Depending on
vehicle configuration) 321
Aspect ratio 415
ATF 381
Attaching a trailer 366
AUDIO menu 164
Audio menu
CD operation 165
Radio operation 164
Satellite radio* operation 164
Auto-dimming*, Rear view mirrors 208
Automatic central locking,
Control system 180
164.boo Seite 571 Freitag, 30. März 2007 12:54 12