phone MERCEDES-BENZ M-Class 2013 W251 Comand Manual

For optimum playback quality:
XDeactivate the “EQ” setting on the
iPod ®
.
Surround-sound playback does not
function for mono signal sources, such as
the medium wave range (MW) in radio
mode.
On some stereo recordings, the sound
characteristics may differ from
conventional stereo playback. Character entry (telephony)
Example: entering characters
00430072
To switch the character bar to
uppercase/lowercase letters
00440042 To switch the character bar from
uppercase/lowercase letters to
digits
0087005D To change the language of the
character bar
00850084 To delete a character/an entry
The example describes how to enter the
surname “Schulz”.
X Call up the input menu with data fields
(Y page 135).
X Select S Sand confirm by pressing 00A1the
COMAND controller.
S
S appears in the data field. X
Select c cand confirm by pressing 00A1the
COMAND controller.
The letter c cis added to S
Sin the data field.
X Repeat the process until the name has
been entered in full.
Other input menu functions:
R to delete a character/entry (Y page 33)
R to switch between upper/lower-case
letters (Y page 33)
R to change the character set (Y page 33)
R to move the cursor in the data field
(Y page 33)
X To enter a phone number: select the
digits one by one in the corresponding data
field by turning 0082005B0083and sliding 00A0005B0064the
COMAND controller and press 00A1to
confirm. Switching data fields
0043
Cursor in the next data field
0044 Storing an entry
0087 0068 and 0069symbols to select a data field
In the input menu, if you want to enter a first
name after you have entered a surname, for
example, proceed as follows to switch
between the data fields:
Option 1
X Select 0068or0069 in the character bar and
press 00A1to confirm.
The input menu shows the data field
selected. 32
Character entry (telephony)At a glance

X
Select a setting by turning 0082005B0083the
COMAND controller and press 00A1to
confirm. Voice Control System settings
Opening/closing the help window
The help window provides information in
addition to the audible instructions during
individualization and during the subsequent
voice control. X
Press 0066.
X Select Settings Settings by turning 0082005B0083the
COMAND controller and press 00A1to
confirm.
X Select Voice Control
Voice Control and press00A1to
confirm.
X Select Help Window
Help Window and press00A1to
confirm.
You have switched the help window on
0073 or off 0053. Individualization
Using individualization, you can fine-tune the
Voice Control System to your own voice and
thus improve voice recognition; see the
separate operating instructions. Bluetooth
®
settings General information about
Bluetooth
®
Bluetooth ®
-capable devices, e.g. mobile
phones, have to comply with a certain profile
in order to be connected to COMAND. Every
Bluetooth ®
device has its own specific
Bluetooth ®
name.
Bluetooth ®
technology is the standard for
short-range wireless data transmission of up
to approximately 10 meters. Bluetooth ®
allows, for example, the exchange of vCards. Bluetooth
®
is a registered trademark of
Bluetooth Special Interest Group (SIG) Inc. Activating/deactivating Bluetooth
®
X Press 0066.
The system menu appears.
X Select Settings Settings by turning 0082005B0083the
COMAND controller and press 00A1to
confirm.
X Select Activate Bluetooth
Activate Bluetooth and press
00A1 to confirm.
This switches Bluetooth ®
on 0073 or off 0053. Setting the system language
This function allows you to determine the
language for the menu displays and the
navigation announcements. The selected
language affects the characters available for
entry.
The navigation announcements are not
available in all languages. If a language is not 40
Setting the system languageSystem settings

Your COMAND equipment
These operating instructions describe all the
standard and optional equipment for your
COMAND system, as available at the time of
going to print. Country-specific differences
are possible. Please note that your COMAND
system may not be equipped with all the
features described. Introduction
Important safety notes
G
WARNING
For safety reasons, only enter a new
destination when the vehicle is stationary.
When you are driving, another passenger
should enter the destination. Read the
Operator's Manual and select the route
before driving.
Bear in mind that at a speed of only 30 mph
(approximately 50 km/h), the vehicle covers
a distance of 44 feet (approximately 14 m) per
second.
COMAND calculates the route to the
destination without taking account of the
following, for example:
R traffic lights
R stop and give way signs
R merging lanes
R parking or stopping in a no parking/no
stopping zone
R other road and traffic rules and regulations
R narrow bridges G
WARNING
COMAND may give incorrect navigation
commands if the actual road/traffic situation
no longer corresponds to the data on the
digital map. Digital maps do not cover all
areas nor all routes in an area. For example,
a route may have been diverted or the
direction of a one-way street may have
changed. For this reason, you must always observe road
and traffic rules and regulations during your
journey. Road and traffic rules and regulations
always have priority over the system's driving
recommendations. G
WARNING
Navigation announcements are intended to
direct you while driving without diverting your
attention from the road and driving.
Please always use this feature instead of
consulting the map display for directions.
Looking at the icons or map display can
distract you from traffic conditions and
driving, and increase the risk of an accident. General notes
Operational readiness of the navigation
system The navigation system must determine the
position of the vehicle before first use or
whenever operational status is restored.
Therefore, you may have to drive for a while
before precise route guidance is possible.
GPS reception Correct functioning of the navigation system
depends, amongst other things, on GPS
reception. In certain situations, GPS
reception may be impaired, there may be
interference or there may be no reception at
all, e.g. in tunnels or parking garages.
i
Using roof carriers may impair the correct
functioning of a roof antenna (phone,
satellite radio, GPS).
Entry restriction On vehicles for certain countries, there is a
restriction on entering data.
The restriction is active from a vehicle speed
of above approximately 3 mph (5 km/h). As
soon as the speed falls below approximately 54
Int
roductionNavigation

X
To make a call: selectCall
Callwith the
COMAND controller and press 00A1to
confirm. COMAND switches to telephone
mode (Y page 128).
i This menu item is available if the waypoint
has a telephone number and if a mobile
phone is connected to
COMAND( Ypage 122).
X To call up the map: selectMap
Map with the
COMAND controller and press 00A1to
confirm.
X You can move the map and select the
destination.
X To store the waypoint in the destination
memory: selectPresets
Presets with the
COMAND controller and press 00A1to
confirm.
Once you have accepted the waypoint, it is
entered in the waypoint menu. Waypoint menu with two waypoints
Editing waypoints
You can:
R
change waypoints
R change the sequence in the waypoint menu
R delete waypoints
To change the sequence, both waypoints
must be entered.
X To change waypoints: select the symbol
for waypoint 1 or 2 in the waypoint menu by turning
0082005B0083the COMAND controller
and press 00A1to confirm.
X Select Edit Editand press 00A1to confirm.
X Use one of the destination entry options
offered.
X To change the sequence of the
waypoints: selectSwap Swapin the waypoint
menu by turning 0082005B0083the COMAND
controller and press 00A1to confirm.
The entries are swapped.
X To delete waypoints: select the symbol
for waypoint 1 or 2 in the waypoint menu
by turning 0082005B0083the COMAND controller
and press 00A1to confirm.
X Select Delete Delete and press 00A1to confirm.
i You can use this menu item to delete a
waypoint directly after entry.
Accepting waypoints for the route X
Select Start
Startin the waypoint menu by
turning 0082005B0083the COMAND controller and
press 00A1to confirm.
The route is calculated with the entered
waypoints.
i The Continue Continue menu item is displayed
instead of Start
StartifCalculate
Calculate
Alternative Routes
Alternative Routes is activated in the
navigation menu (option 2) (Y page 86).
In the example, there are both waypoints 0047
and 0048. Destination input
69Navigation Z

Defining the position for the point of interest search
Selection Characteristic Instructions
Near
Near
Destination Destination Entry is only possible
when route guidance is
active. X
Select Near NearDestination
Destination from the POI
menu and press 00A1to confirm.
X Select a POI category (Y page 72).Current
Current
Position Position The system looks for a
point of interest in the
vicinity of the current
vehicle position. X
Select Current Position Current Position in the POI
menu and press 00A1to confirm.
X Select a POI category (Y page 72).Other City
Other City After entering a city, the
system looks for the POI
within the city. Option 1
X
Select Other Other City
Cityin the POI menu and
press 00A1to confirm.
X If desired, select the state/province
(Y page 58).
X Enter the city. Proceed as described in
the "Entering a city" section
(Y page 58).
X Select a POI category (Y page 72).
Option 2
X Enter a city in the address entry menu
(Y page 58).
X Select POI POIand press 00A1to confirm.
X Select a point of interest category. Search By Name
Search By Name You can call up all the
points of interest in the
digital map or focus your
search on the three
previously selected
positions. X
Select Search Search By
ByName
Name in the POI menu
and press 00A1to confirm.
X Select All POIs
All POIs or one of the three
previously selected positions.
The point of interest list with character
bar appears.
X Proceed as described in the "POI list with
character bar" section (Y page 74).Search Search
By
ByPhone
Phone
Number
Number This function gives you
access to all points of
interest that have a
phone number. X
Select Search By Phone Number Search By Phone Number and
press 00A1to confirm.
You will see a list of phone numbers.
X Proceed as described in the "POI list with
character bar" section (Y page 74). Entering a point of interest
71Navigation Z

The search results display the following
information:
R
an arrow that shows the linear direction to
the point of interest
R the linear distance to the point of interest
R the name of the point of interest
i The arrow and linear distance to the
destination are not visible if you have
entered a POI after entering another city.
The arrow is also not shown when
searching for a POI in the vicinity of the
destination.
Depending on the POI selected, COMAND
uses different reference points in
determining the linear distance to the
destination:
R vicinity of current position: the linear
distance is the distance of the point of
interest from the current vehicle
position.
R vicinity of destination: the linear distance
is the distance from the destination
entered to the point of interest.
Selecting a point of interest 0043
Point of interest with address
0044 To start route calculation
0087 To store an address in the destination
memory
0085 To display details
0083 To make a call (when available) 0084
To cancel selection
006B To display a point of interest's position on
the map
The example has been selected in the BAR
BAR
& RESTAURANT & RESTAURANT POI category. Further
information on searching via POI categories
(Y page 72).
X Select the POI in the POI list by turning
0082005B0083 the COMAND controller and press
00A1 to confirm.
The complete address of the point of
interest selected is shown.
X To start route calculation: select
Start Start 0044and press 00A1to confirm.
X To store an address in the destination
memory: selectSave Save0087 and press 00A1to
confirm. You can now select storing
options (Y page 100).
X To show the detailed view: select
Details Details 0085and press 00A1to confirm.
X To make a call: selectCall Call0083 and press
00A1 to confirm. COMAND switches to
telephone mode (Y page 128).
i This menu item is available if the POI has
a telephone number and a mobile phone is
connected to COMAND (Y page 122).
X To call up the map: selectMap Map006B and
press 00A1to confirm.
X You can move the map and select the
destination (Y page 65). Entering a point of interest
73Navigation Z

Point of interest list with character bar
Search by name in the vicinity of the destination
(example)
If you have selected
Search By Name Search By Namein the
POI menu and then defined the position for
the search (Y page 71), the POI list with
character bar appears.
Depending on your selection, you can select
all available points of interest on the digital
map or the points of interest in the vicinity of
the selected position.
X Proceed as described in "Searching for a
phone book entry" (Y page 133).
If COMAND can assign the characters
entered to one entry unambiguously, the
address entry appears automatically.
X To start route calculation: selectStart Start
and press 00A1to confirm. ZAGAT
®
survey service The Z icon before a search result shows that
a ZAGAT ®
rating is available for this entry. 0043
ZAGAT ratings
0044 To display details
X Select an entry with the "Z" icon by turning
0082005B0083 the COMAND controller and press
00A1 to confirm.
The ZAGAT evaluations appear. ZAGAT example description
X
To show the information: select
Details Details and press 00A1to confirm. 74
Entering a point of interestNavigation

If route guidance has not been activated,
route calculation for the personal point of
interest will start immediately.
X Select Yes
Yes orNo No and press 00A1to confirm.
If you select Yes
Yes, the personal POI is
accepted as the destination.
If you select No No, the process will be aborted.
X To make a call: selectCall
Call and press 00A1
to confirm. COMAND switches to
telephone mode (Y page 129).
i Call
Call is available if the personal POI has a
telephone number and a mobile phone is
connected to COMAND (Y page 122).
X To delete a personal POI: selectDelete
Delete
and press 00A1to confirm.
A prompt appears asking whether you wish
to delete the point of interest.
X Select Yes
Yes orNo No and press 00A1to confirm.
If you select Yes
Yes, the personal POI is
deleted.
If you select No
No, the process will be
canceled. Search & Send
Notes
i To use Search & Send, your vehicle needs
to be equipped with mbrace, a navigation
system and a valid mbrace subscription.
Search & Send is a service assisting you in
entering destinations for the navigation
system. This mbrace service can send a
destination address directly from the Google
Maps ®
website to the navigation system of
your vehicle. Selecting and sending a destination
address
Please also refer to the notes about address
entry online: maps.google.com. X
Call up the maps.google.com website and
destination address in the address entry
field.
X Click the corresponding button to send the
destination address to the e-mail address
registered with mbrace.
X Enter the e-mail address you specified
when setting up your mbrace account into
the corresponding field in the "Send" dialog
window.
X Click "Send". Calling up destination addresses
X
Press the 00D9mbrace information button.
Downloading of the destination address to
the navigation system of your vehicle
begins.
i If you have sent more than one
destination address to your vehicle's
navigation system, you will need to call up
the information individually for every
address to be downloaded. 80
Search & SendNavigation

time. However, no announcements are made
during a phone call.
X To show the menu: press00A1the COMAND
controller.
X Select RPT
RPT in the navigation system menu
bar by turning 0082005B0083the COMAND
controller and press 00A1to confirm.
Switching navigation announcements
on/off X
To switch off: press the006Cbutton
during an announcement.
You will briefly see the message: The The
driving instructions have been
driving instructions have been
muted muted .
X To switch on: press00A1the COMAND
controller.
X Select RPT
RPT in the navigation system menu
bar by turning 0082005B0083the COMAND
controller and press 00A1to confirm.
i COMAND automatically switches the
navigation announcements back on when:
R you have a new route calculated.
R you switch COMAND on again or start the
engine.
Reducing volume during a navigation
announcement The volume of an active audio or video source
can be automatically reduced during a
navigation announcement.
X Select Navi
Navi in the main function bar by
sliding 00A0005Band turning 0082005B0083the COMAND
controller and press 00A1to confirm.
X Select Audio Fadeout Audio Fadeout and press00A1to
confirm.
The function is switched on 0073or off 0053,
depending on the previous status. Setting the volume manually X
Adjust the volume using the 0043control
knob during a navigation announcement.
or
X Select RPT RPTin the map view with the menu
shown and adjust the volume using the
0043 control knob.
Announcing street names If the function is switched on, the name of the
street which you are turning into is
announced.
Announcements are not made in the chosen
language in all countries. They are made when
relevant street names for the selected
language are available in the database.
X
To switch on navigation mode: press the
00BE function button.
X To show the menu: press00A1the COMAND
controller.
X Select Navi
Navi in the main function bar by
sliding 00A0005Bthe COMAND controller and
press 00A1to confirm.
X Select Announce Announce Street
StreetNames
Namesand press
00A1 to confirm.
The function is switched on 0073or off 0053,
depending on the previous status. Quit route guidance
Canceling or continuing route guidance X
To switch on navigation mode: press the
00BE function button.
X To show the menu: press00A1the COMAND
controller.
X Select Destination
Destination in the navigation
system menu bar by turning 0082005B0083the
COMAND controller and press 00A1to
confirm. Route guidance
85Navigation Z

i
You can display destination information
for the destination, for both waypoints and
for the intermediate stop, if they are part of
the route.
If a mobile phone is connected to COMAND
and a phone number is included in the
destination information, you can call it
(Y page 122).
Route overview You can use the route overview to move along
the active route section by section and view
information and details about each section of
the route.
At the top of the display, you will see
information about the highlighted route
section, for example the distance to be driven
on the road and road designation. The
highlighted route section is marked in white
with a red border on the map.
X To switch on navigation mode: press the
00BE function button.
X To show the menu: press00A1the COMAND
controller.
X Select Route
Route in the navigation system
menu bar by turning 0082005B0083the COMAND
controller and press 00A1to confirm.
X Select Route Browser
Route Browser and press00A1to
confirm.
X To view the next or previous route
section: selectNext NextorPrevious
Previous and
press 00A1to confirm.
i If the first or last route section is
highlighted, you cannot select Previous
Previousor
Next
Next .
X To zoom in or out of the map: select0053
or 0052 and press 00A1to confirm.
X To close the route overview: select
Back
Back and press 00A1to confirm. Route display
You can see the route before starting your
journey. This function is only available when
the vehicle is stationary.
X
To switch on navigation mode: press the
00BE function button.
X To show the menu: press00A1the COMAND
controller.
X Select Route Routein the navigation system
menu bar by turning 0082005B0083the COMAND
controller and press 00A1to confirm.
X Select Route Demonstration
Route Demonstration and press
00A1 to confirm.
The map with the crosshair appears.
X To get to the destination: press00A1to
confirm the highlighted symbol.
X To stop the route demonstration:
confirm the 00D8symbol by pressing 00A1.88
Route guidanceNavigation