latch MERCEDES-BENZ ML350 2003 W163 Owner's Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2003, Model line: ML350, Model: MERCEDES-BENZ ML350 2003 W163Pages: 321, PDF Size: 6.31 MB
Page 41 of 321
41 Getting started
Driving
1Latch plate
2Buckle
3Release button
4Seat belt housing
A child’s risk of serious or fatal injuries is
significantly increased if the child restraints
are not properly secured in the vehicle and
the child is not properly secured in the child
restraint.Warning!
G
Never ride in a moving vehicle with the back-
rest reclined. Sitting in an excessively re-
clined position can be dangerous. You could
slide under the seat belt in a collision. If you
slide under it, the belt would apply force at
the abdomen or neck. That could cause se-
rious or even fatal injuries. The backrest and
seat belt provide the best restraint when the
wearer is in an upright position and the belt
is properly positioned on the body.
Warning!
G
Never let more people ride in the vehicle
than there are seat belts available. Be sure
everyone riding in the vehicle is correctly re-
strained with a separate seat belt.Warning!
G
Read and observe the additional warning no-
tices printed in the “Safety and Security”
section (
page 57) and (
page 60).
Page 42 of 321
42 Getting startedDriving
With a smooth motion, pull the belt
from seat belt housing4.
Place the belt over your shoulder.
Push latch plate1 into buckle2 until it
clicks.
If necessary, tighten the lap portion to
a snug fit by pulling shoulder portion
up.
I f ne ce ss ar y, a djus t the s ea t be lt to the
correct height (
page 43).
Proper use of seat belts:
Do not twist the belt when fastening.
Adjust the seat belt so that the shoul-
der portion is located as close as possi-
ble to the middle of the shoulder (it
should not touch the neck or pass un-
der the arm).
Position the lap belt as low as possible
on your hips (over hip joint) and not
across the abdomen.
Place the seat backrest in a nearly up-
right position.
Each seat belt should never be used for
more than one person at a time.
Do not fasten a seat belt around a per-
son and another object at the same
time.
Check your seat belt during travel to
ensure that it is properly positioned.
Ensure that the seat belt is always fit-
ted snugly. You should avoid wearing
bulky clothing, such as winter coats,
when traveling in the vehicle.
Warning!
G
Do not pass belts over sharp edges. They
could tear.
Do not allow the belt to get caught in the
door or in the seat adjustment mechanism.
This could damage the belt.
Never attempt to make modifications to
seat belts. This could impair the effective-
ness of the belts.
Damaged seat belts or belts that were highly
stressed in an accident must be replaced by
an authorized Mercedes-Benz Light Truck
Center.
Page 54 of 321
54 Safety and SecurityOccupant safety
Occupant safetyIn this section you will learn the most im-
portant facts about the restraint systems
of the vehicle.
The restraint systems are
Seat belts
Emergency tensioning device
Airbags
Child seats
Child seat recognition
Lower anchors and tethers for children
(LATCH)
As independent systems their protective
effects work in conjunction with each oth-
er.The warning lamp
1
in the instrument
cluster (
page 26) lights up for about
4 seconds when the key is turned to
position2. It goes out when you start the
engine. This shows that the restraint sys-
tems are operational.
If the lamp does not come on at all or if it
fails to extinguish after approximately
4 seconds or if it comes on thereafter, a
malfunction in the system has been de-
tected.
More information can be found in the
“Practical hints” section (
page 227).
iFor information on infants and children
traveling with you in the vehicle and re-
straint systems for infants and chil-
dren, see “Children in the vehicle”
(page 63).
Warning!
G
In the event that the SRS malfunction indica-
tor lamp lights up during driving or does not
come at all, the SRS may not be operational.
For your safety, we strongly recommend
that you visit an authorized Mercedes-Benz
Light Truck Center immediately to have the
system checked; otherwise the SRS may not
be activated when needed in an accident,
which could result in serious or fatal injury,
or it might deploy unexpectedly and unnec-
essarily which could also result in injury.
Improper work on the restraint systems can
lead to unintentional deployment or opera-
tional failure.
All work on these systems should therefore
only be carried out by an authorized
Mercedes-Benz Light Truck Center.
Page 64 of 321
64 Safety and SecurityOccupant safety
iInformation on child seats with mount-
ing fittings for tether anchorages
(page 67).
For information on child seat mounts –
“LATCH” type (
page 68).
Warning!
G
Never release the seat belt buckle while the
vehicle is in motion, since the special seat
belt retractor will be deactivated.!The use of infant or child restraints is
required by law in all 50 states, the
District of Columbia, the U.S. territo-
ries and all Canadian provinces.
Infants and small children should be
seated in an appropriate infant or child
restraint system properly secured by a
lap-shoulder belt or, if so equipped, a
child restraint lower anchorage system
that complies with U.S. Federal Motor
Vehicle Safety Standards 213 and 225
and Canadian Motor Vehicle Safety
Standard 213 and 210.2. A statement
by the child restraint manufacturer of
compliance with this standard can be
found on the instruction label on the re-
straint and in the instruction manual
provided with the restraint.
When using any infant or child restraint
system, be sure to carefully read and
follow all manufacturer’s instructions
for installation and use.
Please read and observe warning labels
affixed to inside of vehicle and to infant
or child restraints.
Warning!
G
Children 12 years old and under must never
ride in the front seat, except in a Mer-
cedes-Benz authorized BabySmart
TM com-
patible child seat, which operates with the
BabySmart
TM System installed in the vehicle
to deactivate the passenger front airbag
when it is properly installed. Otherwise they
will be struck by the airbag when it inflates
in a crash. If this happens, serious or fatal in-
jury can result.
According to accident statistics, children
are safer when properly restrained in the
rear seating positions than in the front seat-
ing positions. Infants and small children
must ride in back seats and be seated in an
appropriate infant or child restraint system,
which is properly secured with the vehicle's
seat belt and top tether strap, or secured via
lower anchors and top tether strap, fully in
accordance with the child seat manufactur-
er's instructions.
Page 68 of 321
68 Safety and SecurityOccupant safety
When using the center second row seat
for a top tether strap, the left third row
seat should only be used for a child re-
straint system, since exiting the vehicle
may not be possible in an emergency
due to the routing of the top tether
strap.
When installing an infant or child re-
straint system with a top tether strap
on the left second row seat, the left
third row seat should not be occupied. Child seat anchors – “LATCH” type
This vehicle is provided with two “LATCH”
(LOWER Anchors and Tethers for CHil-
dren) type anchors (at each of the outer
rear seats and in the optional third row
seats) for installation of a “LATCH” seat
with matching mounting fittings.
1Anchors
Install a “LATCH” type child seat ac-
cording to the manufacturer’s instruc-
tions.
!An infant and child restraint system
must not be installed on the right
second row seat while a passenger
rides in a third row seat. An infant and
child restraint system installed on the
right second row seat will prevent the
use of the easy-entry/exit feature
(page 95).
iWith a child seat installed in the left
rear seat, the seat belt for the center
seat occupied by a passenger must op-
erate freely. Guide seat belt between
its seat cushion mount and backrest
mount along outside of right side child
seat mount.
Non-“LATCH” type child seats may also
be used and can be installed using the
vehicle’s seat belt system. Install child
seat according to the manufacturer’s
instructions.
Page 144 of 321
144 Controls in detailLoadingCargo floor plates
Removing cargo floor plates
Lift cargo floor plate at rear edge (ar-
row).
Cargo floor plate unhinges automati-
cally.
Remove cargo floor plate by pulling it
rearwards.Storing cargo floor plates
1Hook and loop strip
Fold the left cargo floor plate together.
Open the hook and loop strip at the
bottom of backrest of the third row
seats* and insert cargo floor plate.
Close the hook and loop strip. Installing cargo floor plates
1Opening
2Pins
3Attachment opening
4Latch
Grip into opening1 and guide pins2
into attachment opening3.
The center pin must snap into place in
latch4.
iBefore you can remove the cargo floor
plates, it is possible that the third row
seats* (
page 96) must be removed.
Page 260 of 321
260 Practical hintsFlat tire
Detach the electric air pump.
Reinstall tire valve cap.
Store the electrical plug and the air
hose behind the flap and place the air
pump back in the rear cargo compart-
ment.
Warning!
G
Follow recommended inflation pressures.
Do not overinflate tires. Overinflated tires
can result in sudden deflation (blowout) be-
cause they are more likely to become punc-
tured or damaged by road debris, potholes
etc.
Do not underinflate tires. Underinflated tires
wear unevenly, adversely affect handling
and fuel economy, and are more likely to fail
from being overheated.
Do not overload the tires by exceeding the
specified vehicle capacity weight (as indicat-
ed by the label on the driver’s door latch
post). Overloading the tires can overheat
them, possibly causing a blowout.
Page 302 of 321
302 IndexCargo floor plates 144
Installing 144
Removing 144
Storing 144
Cargo tie-down rings 140
Catalytic converter 198
CD-changer* 238
Center console 27
Lower part 28
Upper part 27
Central locking
Automatic 89
From inside 89
Switch 90
Unlocking from inside 89, 90
Central locking switch 90
Certification label 276
Charge indicator lamp 233
Charging
Vehicle battery 262
Chart
Fuses 271
CHECK ENGINE malfunction indicator
lamp 232
Checking
Coolant level 201, 206Oil level 201, 203
Tire inflate pressure 201
Vehicle lighting 201
Checking weights
Trailer and vehicle 193
Checklist
Off-road driving 187
Returning from off-road driving 191
Child safety 63
Airbags 56
Infant and child restraint systems 54,
60, 63
LATCH child seat mounts 68
Child safety switch see Blocking of rear
door window operation 69
Cigarette lighter
Front center console 156
Cleaning
Cup holder 221
Gear selector lever 221
Hard plastic trim items 221
Headlamps 121
Headliner 221
Instrument cluster 221
Leather upholstery 222
Light alloy wheels 221MB Tex upholstery 222
Plastic and rubber parts 222
Seat belts 221
Steering wheel 221
Windows 220
Windshield 48
Wiper blades 220
Cleaning and care of the vehicle see
Vehicle care 217
Clock 26, 112
Closing
Glove box 152
Hood 203
Liftgate 88
Rear quarter windows* 136
Side windows 135
Sliding/pop-up roof 246
Sliding/pop-up roof* 137
Closing sliding/pop-up roof
In an emergency 246
Cockpit 22, 293
Combination switch 102
High beam flasher 47, 102
Turn signals 47
Windshield wipers 47
Page 307 of 321
307 Index
Headlamps
Automatic control 103
Bi-Xenon 293
Cleaning 220
Cleaning system 121
Cleaning system* 208
Refilling washer fluid 208
Switching off 51
Switching on 46
Washer fluid 290
Washer system 290
Headliner
Cleaning 221
Heated seats 91
Height adjustment
Head restraints 36, 37
Seat belts 43
Steering wheel 37
High beam flasher 47, 102
High beam headlamps
Replacing bulbs 247, 250
Switching on 102
High mounted brake lamp 248
Replacing bulbs 252Hood 202
Closing 203
Opening 202
Hooks
Loading 140
Hydroplaning 183
I
Identification labels 276
Certification label 276
Vehicle identification number
(VIN) 276
Ignition 33
Immobilizer 78
Activating 51, 78
Deactivating 78
Indicator lamp
Adjustable steering column 229
Brake pad wear 234
Coolant 230
Front fog lamps 229
Low engine oil level 229
Indicators, additional
Speedometer display 235
Infant and child restraint systems 63
Installing 67
LATCH child seat mounts 68Inflating
Spare tire 259
Information
About service and warranty 10
Button for Tele Aid* 165
Inside rear view mirror
Antiglare 119
Installing
Head restraint 92
Infant and child restraint systems 67
Wiper blades 254
Instrument cluster 24, 110, 294
Cleaning 221
Coolant temperature gauge 111
Display in the speedometer 111
Illumination 110
Lamps in 233
Outside temperature indicator 112
Instruments and controls see Cockpit 22
Integrated remote control
Canadian programming 171
Erasing memory 171
Hand-held transmitter 169
Operating 171
Rolling code programming 170
Page 308 of 321
308 IndexInterior lighting 107
Activating automatic control 107
Deactivating automatic control 107
Manual operation 108
Reading lamps 108
Interior storage spaces 152
Armrest 153
Cup holder 155
Glove box 152
Storage compartment in front of
armrest 153
Storage compartment under front
passenger seat* 152
Intermittent wiping 122
J
Jack 237, 238
Jump starting 264
K
Key
Global locking 85
Global unlocking 85
Loss of 86
Positions in steering lock 33
Remote control with folding key 84
Unlocking liftgate 85Unlocking the driver’s door, fuel filler
flap 85
Key positions in steering lock 33
Key, Mechanical 242
Key, Remote control
Unlocking with 32
Kickdown 117, 294
L
Labels, identification 276
Lamp bulbs, exterior 247
Lamps, exterior
Front 247
Rear 248
Lamps, indicator and warning
4-ETS 224, 226
ABS 225
Adjustable steering column 229
AIRBAG OFF 59, 232
BAS 73, 225, 226
Battery indicator lamp 233
Brake pad wear 234
Brakes 228
CHECK ENGINE 232
Coolant 230
EBP 229Engine diagnostics 232
ESP 224, 225, 226
Front fog lamps 229
Fuel reserve 233
Instrument cluster ??–233
Low engine oil level 229
LOW RANGE 226
Low washer system fluid level 234
Seat belts 234
Service indicator 215
SRS 54, 227
Turn signals 25
LATCH child seat anchors 68
LATCH child seat mounts 68
Layout of poly-V-belt drive 277
Leather upholstery
Cleaning 222
Lever
For cruise control 146
License plate lamps
Replacing bulbs 248, 252
Liftgate
Closing 88
Opening 85, 87
Opening from inside 87
Opening from outside 87