ventilation MERCEDES-BENZ S-Class 2008 W221 Comand Manual

500 Controls in detailAir ventsOpening and closing air vents
Center air vents
Opening: Turn thumbwheels 4
and5 upward (
page 498).

Closing: Turn thumbwheels 4 and 5
downward.
Side air vents

Opening: Turn thumbwheels next to
side air vents2 and8 upward
(page 498).

Closing: Turn thumbwheels down-
ward.
Rear center console air vents

Increasing/decreasing air volume:
Turn thumbwheelsa or d to the left
or right (
page 498).Ventilated storage compartment
(Canada only)
In vehicles without rear passenger com-
partment climate control*: the storage
compartment under the front armrest can
be ventilated when the automatic climate
control is switched on.1Switching ventilation off
2Switching ventilation on
The air volume is dependent on the setting
of:


air distribution control


air volume control


air vents in the dashboard
The air temperature is about the same as
that of the dashboard air vents. It cannot
be regulated separately.
i
For draft-free ventilation, move the sliders
for the center air vents 3 and 6 (
page 498)
to the middle position.
i
Vehicles without rear passenger compart-
ment climate control*:
The temperature at the air ventsb andc
(
page 498) for rear passenger compartment
will be approximately the same as at the dash-
board center air vents.
!
Extreme temperatures can occur in the stor-
age compartment. Switch off the air vents in the
storage compartment while the heating is
switched on if you are transporting heat-sensi-
tive items in the compartment.
Keep the air vents free of obstruction.

501 Controls in detail
Automatic climate control
Automatic climate control
Automatic climate control panel, front
Item
1
AUTO mode for air distribution and
volume, left
2
Temperature control, left
3
Manual fan speed adjustment, left
4
Front defroster
Item
5
Air recirculation
6
Automatic climate control on/off
7
Residual engine heat and ventilation
(REST)
8
Rear window defroster
Item
9
Manual fan speed adjustment, right
a
Temperature control, right
b
AUTO mode for air distribution and
volume, right

509 Controls in detail
Automatic climate control
Residual engine heat and ventilation
With the engine switched off, it is possible
to continue to heat or ventilate the interior.
This feature makes use of the residual heat
produced by the engine.Activating

Switch off the ignition (
page 370).

Press buttonT (
page 501) up or
down.
The indicator lamp on the button
comes on.
Deactivating

Press buttonT (
page 501) up or
down.
The indicator lamp on the button goes
out.Rear passenger compartment climate
control*
i
If you switch on the residual heat function
when outside temperatures are high, only the
ventilation will be switched on.
i
Regardless of the selected air volume, the
blower operates at low speed when heating. In
case of ventilation the blower operates at higher
speed.
i
How long the system will provide heating de-
pends on


the coolant temperature


the temperature set by the operator
i
The residual heat is automatically turned off:


when the ignition is switched on


after approximately 30 minutes


if the battery voltage drops


if the coolant temperature is too low
Warning!
G
Follow the recommended settings for heat-
ing and cooling as given in the instructions
for the front climate control (
page 501).
Otherwise the windows could fog up, impair-
ing visibility for the driver and endangering
you and others.

566 OperationDriving instructions
For more information on winter driving, see
“Winter driving” (
page 610).
Standing water
Warning!
G
Make sure not to endanger any other road
users when carrying out these braking ma-
neuvers.Warning!
G
If the vehicle becomes stuck in snow, make
sure that snow is kept clear of the exhaust
pipe and from around the vehicle with the
engine running. Otherwise, deadly carbon
monoxide (CO) gases may enter vehicle in-
terior resulting in unconsciousness and
death.
To assure sufficient fresh air ventilation,
open a window slightly on the side of the ve-
hicle not facing the wind.
Warning!
G
The outside temperature indicator is not de-
signed to serve as an ice-warning device and
is therefore unsuitable for that purpose. In-
dicated temperatures just above the freez-
ing point do not guarantee that the road
surface is free of ice.
!
Do not drive through flooded areas or water
of unknown depth. Before driving through water,
determine its depth. Never accelerate before
driving into water. The bow wave could force wa-
ter into the engine and auxiliary equipment, thus
damaging them.
If you must drive through standing water, drive
slowly to prevent water from entering the pas-
senger compartment or the engine compart-
ment. Water in these areas could cause damage
to electrical components or wiring of the engine
or transmission, or could result in water being in-
gested by the engine through the air intake caus-
ing severe internal engine damage. Any such
damage is not covered by the Mercedes-Benz
Limited Warranty.

617 Operation
Vehicle care
Engine cleaning
Prior to cleaning the engine compartment,
make sure to protect electrical compo-
nents and connectors from contact with
water and cleaning agents.
Corrosion protection, such as
MB Anticorrosion Wax, should be applied
to the engine compartment after every
engine cleaning. Before applying, all
control linkage bushings and joints should
be lubricated. The poly-V-belt and all pul-
leys should be protected from any wax.
Vehicle washing
In the winter, thoroughly remove all traces
of road salt as soon as possible.
When washing the vehicle underbody, do
not forget to clean the inner sides of the
wheels.Hand-wash
Do not use hot water or wash your vehicle
in direct sunlight.

Only use a mild car wash detergent,
such as Mercedes-Benz approved Car
Shampoo.

Thoroughly spray the vehicle with a dif-
fused jet of water.
Direct only a very weak spray towards
the ventilation intake.

Use plenty of water and rinse the
sponge and chamois frequently.

Rinse with clean water and thoroughly
dry with a chamois.
Do not allow cleaning agents to dry on
the finish.Automatic car wash
You can have your car washed in an auto-
matic car wash from the start. Automatic
car washes without brushes are prefera-
ble.

To protect the filter system, switch the
automatic climate control to air recir-
culation mode (
page 506).
If the vehicle is very dirty, prewash it be-
fore running it through the automatic car
wash.
i
Vehicles with KEYLESS-GO*:
If a door handle is hit by a strong jet of water, and
a SmartKey with KEYLESS-GO* is in close prox-
imity, i.e. within approximately 3 ft (approxi-
mately 1 m), the vehicle could be inadvertently
locked or unlocked.
!
Do not use scouring agents on these parts.
Never apply strong force and only use a soft,
non-scratching cloth when cleaning the vehicle.
Do not attempt to wipe the surface with a dry
cloth or sponge.
Otherwise you may scratch or damage the paint.
!
Do not clean your vehicle in an automatic
touchless car wash which uses caustic spray.
Otherwise the caustic spray will damage the
paint or ornamental moldings.
!
Make sure that the windshield wiper switch
is set to0 (
page 408). Otherwise, e.g. the rain
sensor could activate and cause the wipers to
move unintentionally. This may lead to vehicle
damage.
Due to the width of the vehicle, fold in exterior
rear view mirrors prior to running the vehicle
through an automatic car wash to prevent dam-
age to the mirrors.

730 Practical hintsBatteries!
The consumer battery located in the trunk is
a valve-r
egulated l
ead a
cid (VRLA) battery, also
referred to as “fleece” battery. Such batteries do
not require topping-up of the electrolyte level.
VRLA batteries therefore do not have cell caps
and the battery cover is non-removable. Do not
attempt to open the consumer battery as other-
wise the battery will be damaged.
Even though VRLA batteries do not require top-
ping-up of the electrolyte level and cannot be
opened to check the electrolyte level, the bat-
tery condition must be checked periodically by
performing a battery conductance test. Refer to
Maintenance Booklet for battery condition test-
ing intervals.
As with any other battery, disconnect the con-
sumer battery if you do not intend to operate
your vehicle for an extended period of time to
prevent battery discharge or connect an acces-
sory battery charge unit expressly approved by
Mercedes-Benz for your vehicle model to main-
tain the battery charge. Contact an authorized
Mercedes-Benz Center for further information.
!
The factory-equipped VRLA battery is
leak-proofed. Only use a battery as replacement
that has the same security features and is of
identical size, voltage, and capacity as the facto-
ry-equipped battery.
The battery, the battery ventilation and the later-
al plug must always be securely installed when
the vehicle is in operation.
Warning!
G
Failure to follow these instructions can re-
sult in severe injury or death.
Never lean over batteries while connecting,
you might get injured.
Battery fluid contains sulfuric acid. Do not
allow this fluid to come in contact with eyes,
skin or clothing. In case it does, immediately
flush affected area with water and seek
medical help if necessary.
A battery will also produce hydrogen gas,
which is flammable and explosive. Keep
flames or sparks away from battery, avoid
improper connection of jumper cables,
smoking, etc.Warning!
G
Do not place metal objects on the battery as
this could result in a short circuit.
Use leak-proof battery only to avoid the risk
of acid burns in the event of an accident.
Take care that you do not become statically
charged, e.g. by wearing synthetic clothing
or rubbing against textiles. For this reason,
you also should not pull or push the battery
over carpets or other synthetic materials.
Never touch the battery first. First touch the
outside body of the vehicle in order to re-
lease any possible electrostatic charges.

732 Practical hintsBatteriesSwitching off vehicle’s internal
electrical functions
Turn off all electrical consumers.

Turn SmartKey in starter switch to po-
sition 0.

Turn SmartKey in starter switch to po-
sition 1.

Wait for 30 seconds.
The vehicle’s internal electrical func-
tions are switched off.

Turn SmartKey in starter switch to po-
sition 0.Disconnecting starter battery

Open the hood (
page 573).

Use a 10-mm open-end wrench to dis-
connect the battery negative lead.

Remove cover2 (
page 731) from
the positive terminal.

Disconnect the battery positive lead.
Removing starter battery
Pull out the battery ventilation hose
from the battery (depending on battery
arrangement in your vehicle model, the
ventilation hose is located either on the
left or right side of the battery).

Fold bar on starter battery up.

Take out the starter battery.
Charging battery
i
Vehicles with KEYLESS-GO: remove the
KEYLESS-GO button (
page 371) and use the
SmartKey with KEYLESS-GO like a normal
SmartKey.
!
Do not remove the SmartKey!
i
For your convenience, have the starter bat-
tery removed by a Mercedes-Benz Center.
Warning!
G
Never charge a battery while still installed in
the vehicle unless the accessory battery
charge unit approved by Mercedes-Benz is
being used. Gases may escape during charg-
ing and cause explosions that may result in
paint damage, corrosion or personal injury.
An accessory battery charge unit specially
adapted for Mercedes-Benz vehicles and
tested and approved by Mercedes-Benz is
available, permitting the charging of the bat-
tery in its installed position. Contact an au-
thorized Mercedes-Benz Center for
information and availability. Charge battery
in accordance with the separate instruc-
tions for the accessory battery charger.i
Have the batteries charged by a
Mercedes-Benz Center. If you charge the batter-
ies yourself, follow the operating instructions for
your charging device.

733 Practical hints
Batteries
Starter battery
Connect the switched-off charging de-
vice to the terminals of the starter bat-
tery. Observe the operating
instructions in the manual for the
charging device while doing so.
Reinstalling starter battery
Install starter battery in engine com-
partment.

Swing retaining bar down.
Reconnecting starter battery

Make sure that the consumer battery in
the trunk is correctly installed and con-
nected.

Turn SmartKey in starter switch to po-
sition 0 and remove.

Connect the positive lead and fasten its
cover2 (
page 731).

Connect negative lead1
(page 731).

Attach ventilation tube.

Switch on the ignition (
page 370).

Start the engine (
page 416).

Check vehicle functions.
!
Only use charging devices with a maximum
charging voltage of 14.8 V.
Warning!
G
During the charge procedure, there is a risk
of acid burns due to gases escaping from
the battery. Do not bend over the battery
during the charge procedure.
!
The battery and the battery ventilation hose
must always be securely installed when the vehi-
cle is in operation.
!
Always connect the starter battery in the or-
der described below. Otherwise, the vehicle’s
electronics could be damaged.
Warning!
G
Do not drive without a properly installed and
connected consumer battery.
Have any work on the consumer battery car-
ried out by an authorized Mercedes-Benz
Center.
!
Never invert the terminal connections.
!
Make sure that the battery has a plug where
the ventilation tube is attached to it.

781 Index
Setting the audio format
(COMAND) 128
Video (COMAND) 132
E
Easy-entry/exit feature 384
COMAND menu 268
EBP 72
Electrical fuses see Fuses
Electrical outlet see Power outlet
Electrical system, Technical Data 760
Electronic Brake Proportioning see EBP
Electronic parking brake 422
Indicator lamp 29, 630
Messages in display 667
Warning lamp 29, 630
Electronic Stability Program see ESP
®
Electronic traction system 73
Emergency call system 542
Emergency calls, Tele Aid 544
Emergency engine shut-down 744
Emergency operation
(Limp-Home Mode) 443
Emergency operations
Locking the vehicle 708
Releasing from inside 516
Remote door lock 550Remote door unlock 549
Unlocking the trunk 709
Unlocking the vehicle 708
Emergency tensioning device see ETD
Emergency, In case of
Battery, Jump starting 734
First aid kit 705
Flat tire 723
Fuses 741
Roadside Assistance 15
Roadside Assistance (Tele Aid) 546
Towing the vehicle 737
Emission control 568
Emission control information label 749
Emission control system warranties 14
Engine
Belt layout 750
Cleaning 617
Compartment 573
Coolant 579, 767, 771
Malfunction indicator lamp 29, 632
Number 748, 749
Oil 578, 765, 769
Oils 575
Residual heat and ventilation 509
Starting 416Technical data 751
Turning off 424
Engine coolant see Coolant
Engine oil 575
Adding 578
Additives 769
Checking level 575
Checking level (Dipstick) 577
Checking level (Instrument cluster
control system) 575
Consumption 575
Dipstick 577
Filler neck 577, 578
Messages in display 576, 694
Recommended engine oils and
oil filters 765
ESP
®Four wheel electronic traction system
with ESP
®
76
ESP
®
72
Messages in display 662, 673
Warning lamp 29, 629, 634
ETD 55
Safety guidelines 44

790 IndexPower closing assist for doors and
trunk lid 368
Power folding exterior rear view
mirrors 389
Power outlet 538
Power tilt/sliding sunroof 518
Opening/closing 518
Synchronizing 520
Power washer 616
Power windows 410
Blocking of rear window operation 64
Cleaning 622
Opening/closing 410
Practical hints 642, 705
Premium unleaded gasoline 571, 767,
770
PRE-SAFE
®
57
Message in display 656
Messages in display 663
PRE-SAFE
® Brake*
Intermittent signal tone 80
Preventive occupant safety see PRE-SAFE
®
Problems
While driving 420
With vehicle 20
Product information 13Production options weight 607
Program mode see Automatic
transmission, Automatic shift program
Program mode selector switch
Automatic shift program 436
Proper use of the vehicle 19
PSI 608
Push-start see Tow-start
R
RACETIMER see Control system
instrument cluster menus, AMG
Radio
FM/AM operation (COMAND) 102
Saving stations, FM/AM
(COMAND) 106
Selecting satellite radio channel
(Instrument cluster control
system) 295
Selecting stations 294
Submenu overview, FM/AM
(COMAND) 102
Switching wavebands, FM/AM
(COMAND) 103
Tuning in stations/channels 103
Voice Control 334Radio transmitters, control and
operation 567
Range (distance to empty) 292
Reading lamps in the front 407
Reading lamps in the rear 407
Real-time traffic (COMAND) 248
Rear door window
Blocking operation 64
Rear fog lamp
Replacing bulbs 715
Rear lamps see Tail lamps
Rear seats
Adjustment 373
Folding back and placing upright
rear head restraints 380
Head restraints 379
Heating* 377
Multicontour* 383
Setting front passenger seat position
from rear 377
Ventilation* 378
Rear View Camera* 487
Camera lens 487
Cleaning camera lens 621
Switching on 489
View through the camera 488