lock MERCEDES-BENZ S-Class MAYBACH 2017 W222 Comand Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2017, Model line: S-Class MAYBACH, Model: MERCEDES-BENZ S-Class MAYBACH 2017 W222Pages: 230, PDF Size: 8.27 MB
Page 56 of 230
You can find further information on the auto-
matic headlamp mode in the vehicle Operator's
Manual.
Switching locator lighting on/off
XCall upVehicle Settings(Ypage 51).
XTo select LocatorLighting: turn and press
the controller.
The function switches on or off, depending on
the previous setting.
You can find further information in the vehicle
Operator's Manual.
Activating/deactivating the auto-
matic door locking mechanism
When the automatic locking feature is switched
on, the vehicle is locked automatically when the
ignition is switched on and the vehicle is travel-
ing faster than walking pace.
XCall up Vehicle Settings(Ypage 51).
XTo select Automatic Locking: turn and
press the controller.
The function switches on or off, depending on
the previous setting.
You can find further information in the vehicle
Operator's Manual.
Setting the switch-off delay time
Interior lighting switch-off delay time
The interior lighting is activated for the duration
of the switch-off delay time when the SmartKey
is removed from the ignition lock.
XCall up Vehicle Settings(Ypage 51).
XTo select Interior Lighting DelayedSwitch-off: turn and press the controller.
The setting element is active.
XTo change the switch-off delay time: turn the
controller.
You can find further information in the vehicle
Operator's Manual.
Exterior lighting switch-off delay time
If you switch on the Exterior LightingDelayed Switch-offfunction, the exterior
lighting is switched on for a short time after the
engine is switched off. The light switch must be
set to Ã.
The duration of the exterior lighting delayed
switch-off time can be adjusted individually. The
exterior lighting remains on for the maximum
duration of 60 seconds after the engine is
switched off. If you close all the doors and the
tailgate, the exterior lighting switches off after
the set time.
54Vehicle settings
Vehicle functions
Page 65 of 230
Pre-entry climate control via SmartKey
This function is only available for
PLUG‑IN HYBRID vehicles.
When you unlock the vehicle, the driver's seat
and the vehicle interior:
Ris briefly pre-heated
Ris briefly pre-ventilated
XCall up the climate control menu (Ypage 60).
XTo selectPre-entry Climate Control
via Key: turn and press the controller.
XTo switch on or off: turn and press the con-
troller.
XTo exit the menu: press the %button.
Further information on pre-entry climate control
via SmartKey (see the vehicle Operator's Man-
ual).
Pre-entry climate control at time of
departure
This function is only available for
PLUG‑IN HYBRID vehicles.
The driver's seat and the vehicle interior are
heated or cooled prior to the set departure time.
XCall up the climate control menu (Ypage 60).
XTo select Pre-entry Climate Ctrl. at
DepartureTime: turn and press the control-
ler.
A rotary menu appears.
XTo select the setting: turn the controller.
The menu symbol, text and image show the
selected setting.
XTo exit the menu: press the %button.
Further information on pre-entry climate control
(see the vehicle Operator's Manual).
Child-proof locks
Switching the rear compartment dis-
plays on/off
This function serves to switch the rear-compart-
ment displays on/off.
XPress the Øbutton.
or
XPress Vehiclein the main function bar.
The vehicle menu is displayed.
XTo select ParentalControl: turn and press
the controller.
The menu to select the side in the rear com-
partment is activated.
XSelect Rear LeftorRear Right.
XTo switch Displayon/off: turn the controller.
Exiting the vehicle settings:
XTo select &: slide 6and press the con-
troller.
Locking/unlocking rear compart-
ment displays
This function serves to lock/unlock the rear-
compartment displays.
XPress the Øbutton.
or
XPress Vehiclein the main function bar.
The vehicle menu is displayed.
Child-proof locks63
Vehicle functions
Z
Page 66 of 230
XTo selectParentalControl: turn and press
the controller.
The menu to select the side in the rear com-
partment is activated.
XSelect Rear LeftorRear Right.
XTo select Lockto lock/unlock the rear com-
partment displays: slide 9and press the
controller.
The display is locked, a corresponding mes-
sage with &appears on the screen.
Unlock
appears in the display.
Exiting the vehicle settings:
XTo select &: slide 6and press the con-
troller.
iThe volume can still be adjusted if you have
locked the rear compartment display. It can
also be switched on/off using the integrated
switch.
360° camera
General notes
The 360° camera covers the immediate sur-
roundings of the vehicle and assists you, for
instance when parking or at exits with reduced
visibility.
The 360° camera is only an aid. It is not a
replacement for your attention to your immedi-
ate surroundings. You are always responsible
for safe maneuvering and parking. Make sure
that no persons or animals are in the maneu-
vering range.
Further information on the 360°camera can be
found in the vehicle Operator's Manual.
Displaying the 360° camera image
The 360° camera image can be displayed if:
Ryour vehicle is equipped with a 360° camera
Rthe multimedia system is switched on
Rthe 360° Camerafunction is switched on
XPress the Øbutton.
The vehicle menu is displayed.
XSelect 360° Camera.
The 360° camera image appears in split-
screen mode. You will see the previous view on the display if,
when the function is switched on:
Ryou turn the SmartKey to position
1in the
ignition lock
Ryou select transmission position P
Rwhen you are driving at moderate speeds
Manually switching the display
XTo select &: slide 6and press the con-
troller.
Automatically switching the display:
XYou can switch on the 360 camera display
automatically using the reverse gear
(
Ypage 64).
Switching automatic mode of the
360° camera on/off
This function activates the 360° camera when
reverse gear is engaged.
XPress the Øbutton.
or
XPress Vehiclein the main function bar.
The vehicle menu is displayed.
XTo switch to the menu bar: slide 6the con-
troller.
XTo select System Settings: turn and press
the controller.
XSelect 360° Camera.
XSelectActivation by R gear.
The function is switched on Oor off ª,
depending on the previous status.
Opening the camera cover for clean-
ing
XTo select Open Camera Coverin the 360°
camera menu: turn the controller and press to
confirm.
The Please Wait...
message appears for
approximately three seconds.
The camera cover opens.
The camera cover closes automatically if:
Rthe ignition is switched off
Rthe vehicle exceeds a moderate speed
64360° camera
Vehicle functions
Page 73 of 230
there are also carpool lanes which can only be
used when there are three or more people in the
vehicle. In California, lone drivers can use a car-
pool lane if their vehicle's emission level or fuel
consumption is below a fixed threshold.
Carpool lanes may be reserved for specific
times (e.g. during the peak period).
Carpool lanes are indicated by a diamond sym-
bol on specific road signs and on the road sur-
face. The road signs may also include the des-
ignation CARPOOL. The lanes are arranged as a
separate lane next to the others or are built as a
physically separate lane.
Depending on the setting underUse Carpool
Lanes, the multimedia system uses carpool lanes when calculating the route. The multime-
dia system then guides you in and out of carpool
lanes using visual and acoustic driving direc-
tions.
XTo switch to navigation mode:
press the
ß button.
XTo show the menu: slide6the controller.
XTo select Options: turn and press the con-
troller.
XSelect Route Settings.
XSelectAvoid Options.
XSelectUse Carpool Lanes.
Carpool lanes will either be used Oor avoi-
ded ªwhen calculating the route.
Destination entry
Important safety notes
GWARNING
If you operate information systems and communication equipment integrated in the vehicle while driving, you will be distracted from traffic conditions. You could also lose control of the vehicle.
There is a risk of an accident.
Only operate the equipment when the traffic situation permits. If you are not sure that this is
possible, park the vehicle paying attention to traffic conditions and operate the equipment when
the vehicle is stationary.
You must observe the legal requirements for the country in which you are currently driving when
operating the multimedia system.
Destination entry may be blocked while driving, depending on the country specifications.
General notes
The various character entry options are described for the controller. Alternatively you can use the
touchpad to enter characters and select menus (Ypage 28).
Destination entry71
Navigation
Z
Page 82 of 230
Using the map
:Crosshair
;Distance of crosshair position from current vehicle position
XTo switch to navigation mode:press theßbutton.
XTo show the menu: slide6the controller.
XTo select Destination: turn and press the controller.
XSelectUsing Map.
The map with crosshair is shown.
XTo move the map: slide1, 4or2 the controller.
XTo change the map scale: turn the controller until the desired map scale is selected.
The scale is displayed at the bottom. Turning clockwise zooms out from the map; turning counter-
clockwise zooms in.
XTo select a destination: press the controller.
If several destinations are available in the area around the crosshair, these are also displayed.
XTo select a destination from the selection list: turn and press the controller.
If the digital map provides navigable address data, you will see the destination address in the
address entry menu.
XTo start route calculation: selectStart(Ypage 74).
Entering intermediate destinations
Introduction
You can also map the route to the destination
yourself by entering up to four intermediate des-
tinations. The sequence of the intermediate des-
tinations can be changed at any time.
The navigation system provides a selection of
predefined destinations in eight categories for
this purpose, e.g. Gas Station
orRestau‐rants. You can also use the destination entry
options to enter intermediate destinations.
Creating intermediate destinations
XTo switch to navigation mode: press the
Ø button.
XTo show the menu: slide6the controller.
XTo select Destination: turn and press the
controller.
XSelect Intermediate Destinations.
XTo select a category or Other: turn and press
the controller.
After selecting a category, the POIs which are
available along the route and in the vicinity are displayed.
First, a search for destinations along the route
is performed. The search for destinations is
80Destination entry
Navigation
Page 93 of 230
Display mode:while driving on the highway, gas stations, rest stops, rest areas and highway exits
are displayed along with their immediate distances from the current vehicle position.
Highway information facilitates route guidance to a POI (e. g. rest stops, highway exits) and use of
th e traffic jam function. The remaining route on the highway in this case is blocked in the direction
of travel from the selected exit.
XTo call up th e selection mode: while displayingthe highway information, slide 9thecon-
troller.
The marker is on the highway information. The associated position is marked on the map.
XTo start route guidance and use additional functions: select a POI by turningand pressing the
controller.
The POI details are displayed.
The POI can now be:
RStore in th e address book (Ypage 99)
RView on the map (Ypage 83)
RCall if a phone is connected and a phone number is available (Ypage 120)
RSelect for route guidance and calculat earoute to it (Ypage 74)
XTo use thetraffic ja m function: selectDetourby turning and pressing th econtroller.
The traffic jam function appear s(Ypage 95).
Navigation announcements
Repeating navigation announcements
If you missed the current navigation announce-
ment, you can call it up again.
XTo switch to navigation mode: press the
Ø button.
XTo sho wthemenu: slide6thecontroller.
XTo select+: turn and press thecontroller.
iIf th eRepeat Spoken Drivin gRecom‐mendation sfunction has previously been
added as a favorite, you can alternatively
select th e function using thefavorite s button
(
Ypage 38).
Setting the volume ma nually
XSetth e volume using the thumbwheel during
th e navigation announcement.
iWhen you start the engine, the volume will
be at its lowest setting.
Route guidance91
Navigation
Z
Page 98 of 230
Real-time traffic reports
Requirements
i
This function is currently not available for
Canada.
In order to receive real-time traffic reports via
satellite radio, you need to subscribe to SIRIUS
XM Satellite Radio Traffic Message Service. Further information on satellite radio
(
Ypage 158).
The multimedia system can receive traffic
reports via satellite radio and take account of
these for route guidance in the navigation sys-
tem. Received traffic reports are displayed on
the map either as text or as symbols.
Real-time traffic reports on the map
:Traffic reports can be received or traffic reports are available
;Icon delimiting the section of the route affected (color lines)
=Traffic incident on the route (traffic jam symbol)
If display :is not shown, traffic reports cannot be received.
The navigation system can show certain traffic incidents on the map. Traffic reports are shown on
the map at scales of 1/32 mi to 20 mi.
XTo hide the menu: slide5and press the controller.
The map can be seen in the full-screen display.
XTo set the map scale: turn the controller until the desired map scale is selected.
:Traffic jam on the route
;Slow-moving traffic on the route
=Road blocked
96Real-time traffic reports
Navigation
Page 99 of 230
?Traffic jam
ATraffic warning
BDashed red and white line delimiting the traffic warning
CRoad block (crosses along the affected road)
DSlow-moving traffic (orange line along the affected route)
ETraffic jam (red line along the affected route)
Displaying real-time traffic reports
Starting a search for traffic reports
XTo switch to navigation mode: press the
Ø button.
XTo show the menu: slide6the controller.
XTo select Traffic: turn and press the con-
troller.
XTo close the report: press the controller.
Traffic symbol information
:Affected roads with indication of direction
;Symbol for report type, e.g. traffic flow mes-
sage
XTo switch to navigation mode: press the
Ø button.
XTo show the menu: slide6the controller.
XTo select Traffic: turn and press the con-
troller.
XTo select Traffic Symbol Information:
turn and press the controller.
The map appears and shows the available
traffic information as icons. The first traffic
information is highlighted.
XTo highlight additional traffic symbols, select
Nextor Previous.
XTo move the map: selectMap.
You can move the map to enable further traf-
fic information to be displayed.
You can have the traffic report relevant to a traf-
fic icon shown.
XTo select Details: turn and press the con-
troller.
The report shows the following information:
RState/province, road and display of the affec-
ted direction
RSection of the road to which the traffic report applies
RTraffic icon and traffic report
XTo close the detailed display: press the
% button.
Displaying reports on the route
The function is only available while route guid-
ance is active. It shows the available traffic
reports affecting the current route.
If there are no reports for the route or the func-
tion is not supported in the selected language:
Real-time traffic reports97
Navigation
Z
Page 107 of 230
Other functions:
RMoving the map (Ypage 68)
RSetting the map scale (Ypage 101)
Building images
In the map scales 1/32 mi (20 m) and 1/16 mi (50 m) important buildings are depicted realistically
on the map. Other buildings are shown as models.
Elevation model
Cities located in mountainous regions are realistically depicted using elevation modeling.
Avoiding an area
General notes
The navigation system enables you to avoid areas you do not wish to drive through.
If you activate or deactivate a route block while route guidance is active, the navigation system will
calculate a new route. If you activate or deactivate a route block while route guidance is inactive, the
navigation system will use the new setting for the next route guidance.
Map functions105
Navigation
Z
Page 108 of 230
The calculated route may include an area to be avoided if:
Ryour destination is located in such an area
Rthere is no alternative route of comparable length available
Highways within blocked areas are always taken into consideration in the route calculation.
iEquipment with a touchpad: alternatively you can carry out this operation using the touchpad
(Ypage 28).
Avoiding a new area
XTo switch to navigation mode: press theßbutton.
XTo show the menu: slide6the controller.
XTo select Options: turn and press the controller.
XSelectRoute Settings.
XSelectAvoid Options.
XSelectAvoid Area.
XSelectAvoid New Area.
A menu appears.
XSelect Using MaporAddress Entry.
If you select Using Map, the map with crosshair appears.
If you select Address Entry
, the address entry menu appears where you can enter the address
(Ypage 72). The map appears with the crosshair after the address is entered.
XTo select an area: when the map with crosshair appears, press the controller.
A red square appears on the map, symbolizing the area to be blocked.
XTo change the size of the area, turn the controller.
The map scale is shown at the bottom of the display. The needle is on the map scale currently
selected.
XWhen the desired size is set, press the controller.
The area is entered into the list.
106Map functions
Navigation