Starter battery MERCEDES-BENZ SL550 2007 R230 Owner's Manual
[x] Cancel search | Manufacturer: MERCEDES-BENZ, Model Year: 2007, Model line: SL550, Model: MERCEDES-BENZ SL550 2007 R230Pages: 473
Page 41 of 473
40 Getting startedUnlockingSmartKeyStarter switch0For removing SmartKey
1Power supply for some electrical con-
sumers, such as seat adjustment
2Ignition (power supply for all electrical
consumers) and driving position
All lamps (except high beam headlamp
indicator lamp and turn signal indicator
lamps unless activated) in the instru-
ment cluster come on. If a lamp in the
instrument cluster fails to come on
when the ignition is switched on, have
it checked and replaced if necessary.If a lamp in the instrument cluster re-
mains on after starting the engine or
comes on while driving, refer to “Lamps
in the instrument cluster”
(
page 332).
3Starting position
SmartKey with KEYLESS-GO*
KEYLESS-GO start/stop button1USA only
2Canada only
i
When you switch on the ignition, the indica-
tor and warning lamps (except high beam head-
lamp indicator lamp and turn signal indicator
lamps unless activated) in the instrument cluster
come on. The indicator and warning lamps (ex-
cept high beam headlamp indicator lamp and
turn signal indicator lamps if activated) should go
out when the engine is running. This indicates
that the respective systems are operational.
i
The SmartKey can only be removed from the
starter switch with the gear selector lever in
position P.
!
If the SmartKey cannot be turned in the
starter switch, the starter battery may not be
sufficiently charged.
Check the starter battery and charge it if
necessary (
page 414).
Get a jump start (
page 419).
To prevent accelerated battery discharge or a
completely discharged battery, always remove
the SmartKey from the starter switch when the
engine is not in operation.
Page 54 of 473
53 Getting started
Driving
Starting with KEYLESS-GO*
You can start your vehicle without the
SmartKey in the starter switch using the
KEYLESS-GO start/stop button on the
gear selector lever.KEYLESS-GO start/stop button1USA only
2Canada only
Make sure the gear selector lever is set
to P.
Depress the brake pedal during the
starting procedure. Do not depress ac-
celerator.
Press the KEYLESS-GO start/stop
button once.
The engine starts if the SmartKey with
KEYLESS-GO is in the vehicle.
For information on turning off the engine
with KEYLESS-GO, see “Turning off with
KEYLESS-GO*” (
page 62).
Starting difficulties
If the engine does not start as described,
carry out the following steps:
If you are starting the engine with the
SmartKey: Turn SmartKey in starter
switch to position0 and repeat starting
procedure.
If you are starting the engine with
KEYLESS-GO*: Close any doors that
may be open to allow for better detec-
tion of the SmartKey with
KEYLESS-GO.
Or:
Start the engine with the SmartKey as
radio signals from another source may
be interfering with the SmartKey with
KEYLESS-GO*.
Repeat the starting procedure
(page 52). Remember that extended
starting attempts can drain the battery.
Get a jump start (
page 419).
If the engine does not start after several
starting attempts, there could be a mal-
function in the engine electronics or in the
fuel supply system.
Contact an authorized Mercedes-Benz
Center.
Page 97 of 473
96 Safety and SecurityAnti-theft systemsImmobilizer
The immobilizer prevents unauthorized
persons from starting your vehicle.
Activating
With the SmartKey
Remove the SmartKey from the starter
switch.
With KEYLESS-GO*
Press the start/stop button on the gear
selector lever once.
The engine is turned off.
Open the driver’s door.Deactivating
With the SmartKey
Turn the SmartKey in the starter switch
to position2 (
page 40).
With KEYLESS-GO*
Switch on the ignition (
page 41).
Anti-theft alarm system
Once the alarm system has been armed, a
visual and audible alarm is triggered when
someone opens
a door
the trunk lid
the hood
a storage compartment in the rear
the glove box
the storage compartment under the
armrest
The alarm will stay on, even if the activat-
ing element (a door, for example) is imme-
diately closed.
i
Starting the engine will also deactivate the
immobilizer.
In case the engine cannot be started (yet the
vehicle’s battery is charged), the system is not
operational. Contact an authorized
Mercedes-Benz Center or call
1-800-FOR-MERCedes (in the USA), or
1-800-387-0100 (in Canada).
Page 282 of 473
281 Operation
Engine compartment
Battery
Your vehicle is equipped with two batter-
ies:
The starter battery (located in the en-
gine compartment)
The battery for electrical consumers
(located in the trunk)
These batteries should always be suffi-
ciently charged in order to achieve their
rated service life. Refer to Maintenance
Booklet for battery maintenance intervals.
If you use your vehicle mostly for
short-distance trips, you will need to have
the battery charge checked more frequent-
ly.
When replacing batteries, always use bat-
teries approved by Mercedes-Benz.
If you do not intend to operate your vehicle
for an extended period of time, consult an
authorized Mercedes-Benz Center about
steps you need to observe.Batteries contain materials that can harm
the environment if disposed of improperly.
Recycling of batteries is the preferred
method of disposal. Many states require
sellers of batteries to accept old batteries
for recycling.
Warning!
G
Observe all safety instructions and precau-
tions when handling automotive batteries.
Risk of explosion.
Fire, open flames and smoking
are prohibited when handling
batteries. Avoid creating sparks.
Battery acid is caustic. Do not
allow it to come into contact
with skin, eyes or clothing.
Wear suitable protective cloth-
ing, especially gloves, apron and
faceguard.
Wear eye protection.
Rinse any acid spills immediate-
ly with clear water. Contact a
physician if necessary.
Keep children away.
Follow the instructions in this
Operator’s Manual.
Page 380 of 473
379 Practical hints
What to do if …
Left display
Right display
Possible cause/consequence
Possible solution
F
Key
not detected
The SmartKey with KEYLESS-GO* is
not recognized while the engine is
running because:
The SmartKey with
KEYLESS-GO* is not in the vehi-
cle.
There is strong radio-frequency
interference.
Stop the vehicle in a safe location or as soon
as it is safe to do so.
Search for the SmartKey with KEYLESS-GO*.
Otherwise the vehicle cannot be centrally
locked nor can the engine be started again af-
ter the engine is stopped.
Operate the vehicle with the SmartKey with
KEYLESS-GO* in the starter switch
Key
not detected
The SmartKey with KEYLESS-GO* is
not recognized when attempting to
start the engine with the
KEYLESS-GO start/stop button* on
the gear selector lever because:
The SmartKey with
KEYLESS-GO* is not in the vehi-
cle.
The battery in the SmartKey
with KEYLESS-GO* is not insert-
ed properly or completely dis-
charged.
Change the position of the SmartKey with
KEYLESS-GO* in the vehicle.
Make sure the batteries in the SmartKey with
KEYLESS-GO* are properly inserted
(page 395) and are not discharged
(page 110).
Start the engine with the SmartKey with
KEYLESS-GO* in the starter switch if
necessary.
Page 415 of 473
414 Practical hintsBatteriesFor more information on batteries, see
“Battery” (
page 281).
Your vehicle is equipped with two
batteries:
The starter battery
The battery for electrical consumers
(consumer battery), located in the
trunk
The starter battery is located on the
right-hand side of the engine compart-
ment.
1Positive terminal
2Negative terminal
3Battery ventilationThe consumer battery is located on the
right-hand side of the trunk.
4Positive terminal
5Negative terminal
!
The starter battery, its filler caps, and the
ventilation hose must always be securely in-
stalled when the vehicle is in operation.
!
The consumer battery located in the trunk is
a valve-regulated lead acid (VRLA) battery, also
referred to as “fleece” battery. Such batteries do
not require topping-up of the electrolyte level.
VRLA batteries therefore do not have cell caps
and the battery cover is non-removable. Do not
attempt to open the consumer battery as other-
wise the battery will be damaged.
Even though VRLA batteries do not require top-
ping-up of the electrolyte level and cannot be
opened to check the electrolyte level, the bat-
tery condition must be checked periodically by
performing a battery conductance test. Refer to
Maintenance Booklet for battery condition test-
ing intervals.
As with any other battery, disconnect the con-
sumer battery if you do not intend to operate
your vehicle for an extended period of time to
prevent battery discharge or connect an acces-
sory battery charge unit expressly approved by
Mercedes-Benz for your vehicle model to main-
tain the battery charge. Contact an authorized
Mercedes-Benz Center for further information.
Page 416 of 473
415 Practical hints
Batteries
!
The factory-equipped VRLA battery is
leak-proofed. Only use a battery as replacement
that has the same security features and is of
identical size, voltage, and capacity as the
factory-equipped battery.
The battery, the battery ventilation and the later-
al plug must always be securely installed when
the vehicle is in operation.
Warning!
G
Failure to follow these instructions can re-
sult in severe injury or death.
Never lean over batteries while connecting,
you might get injured.
Battery fluid contains sulfuric acid. Do not
allow this fluid to come in contact with eyes,
skin or clothing. In case it does, immediately
flush affected area with water and seek
medical help if necessary.
A battery will also produce hydrogen gas,
which is flammable and explosive. Keep
flames or sparks away from battery, avoid
improper connection of jumper cables,
smoking, etc.
!
Never loosen or detach battery terminal
clamps while the engine is running or the
SmartKey is in the starter switch. Otherwise the
alternator and other electronic components
could be severely damaged.
Have the starter battery checked regularly by an
authorized Mercedes-Benz Center.
Refer to Maintenance Booklet for maintenance
intervals or contact an authorized
Mercedes-Benz Center for further information.
Warning!
G
Do not place metal objects on the battery as
this could result in a short circuit.
Use leak-proof batteries only to avoid the
risk of acid burns in the event of an acci-
dent.
Warning!
G
The brake system requires electrical power
to operate.
A malfunction in the vehicle’s power supply
or electrical system may impair brake sys-
tem operation and switch it into its emer-
gency operation mode. The same applies if
battery is disconnected. To brake, the driver
must then apply significantly greater brake
pedal pressure and depress the pedal much
further to obtain the expected braking ef-
fect. If necessary, apply full pressure to the
brake pedal. Brakes are only applied to the
front wheels. Stopping distance is in-
creased! Adjust your driving style according-
ly. For more information, see
“Electro-hydraulic brake system”
(page 92).
Page 417 of 473
416 Practical hintsBatteries
Disconnecting the batteries
Apply the parking brake (
page 61).
Make sure the gear selector lever is set
to position P (
page 168).
Close the retractable hardtop
(page 199).
Turn off all electrical consumers.
Turn off the engine (
page 62).
Remove the SmartKey from the starter
switch.
Vehicles with KEYLESS-GO*: Open
the driver’s door.
Open the trunk.
Read and observe safety instructions
and precautions (
page 281).
Open the luggage cover in the trunk
(page 206).
Remove the trunk floor.
The battery for electrical consumers is
located in the right hand area of the
trunk (
page 388).
Use the 10 mm open-end wrench from
the vehicle tool kit to disconnect the
negative lead from negative
terminal5 of the consumer battery
(page 414).
Warning!
G
With a disconnected battery
you will no longer be able to turn the
SmartKey in the starter switch and
pressing the KEYLESS-GO* start/stop
button on the gear selector lever will
have no effect
the gear selector lever will remain
locked in positionP
!
Always disconnect the batteries in the order
described below, even if you only want to charge
the starter battery, for example. Otherwise the
vehicle’s electronics can be damaged.
Page 418 of 473
417 Practical hints
Batteries
Open the hood (
page 274).
Use the 10 mm open-end wrench from
the vehicle tool kit to disconnect the
negative lead from negative
terminal2 of the starter battery
(page 414).
Remove the covers from the positive
terminals 1 and 4 (
page 414).
Disconnect the positive lead from pos-
itive terminal 4 of the consumer bat-
tery (
page 414).
Disconnect the positive lead from pos-
itive terminal 1 of the starter battery
(page 414).
Removing the batteries
Removing the consumer battery
Remove the screws securing the bat-
tery in the trunk.
Remove the battery support and
bracket.
Pull out the battery ventilation hose
from the battery.
Depending on battery arrangement in
your vehicle model, the ventilation tube
is located either on the left or right side
of the battery.
Take out the battery.
Removing the starter battery
Remove the screws securing the start-
er battery in the engine compartment.
Pull battery ventilation 3
(page 414) out of the battery.
Lift the retaining bracket.
Remove the battery.
Charging and reinstalling batteriesWarning!
G
Never charge a battery while still installed in
the vehicle unless the accessory battery
charge unit approved by Mercedes-Benz is
being used. Gases may escape during charg-
ing and cause explosions that may result in
paint damage, corrosion or personal injury.
An accessory battery charge unit specially
adapted for Mercedes-Benz vehicles and
tested and approved by Mercedes-Benz is
available, permitting the charging of the bat-
tery in its installed position. Contact an au-
thorized Mercedes-Benz Center for
information and availability. Charge battery
in accordance with the separate instruc-
tions for the accessory battery charger.
Page 419 of 473
418 Practical hintsBatteries
Charge batteries in accordance with
the instructions of the battery charger
manufacturer.
Reinstall the charged batteries. Follow
the previously described steps in re-
verse order.
Reconnecting the batteries
Turn off all electrical consumers.
Install starter battery in the designated
location in the engine compartment.
Install consumer battery in the desig-
nated location in the trunk.
Attach supports and brackets.
Tighten support and bracket screws.
Connect positive lead 4 (
page 414)
of the consumer battery and positive
lead 1 (
page 414) of the starter bat-
tery and fasten covers.
Connect negative lead 2
(page 414) of the starter battery.
Connect negative lead 5
(page 414) of the consumer battery.
Reinstall the trunk floor.
Close trunk luggage cover
(page 206).
!
Always connect the batteries in the order
described below. Otherwise the vehicle’s elec-
tronics can be damaged.
!
Never invert the terminal connections!
i
The following procedures must be carried
out following any interruption of battery power
(e.g. due to reconnection):
Resynchronize the ESP
® (page 355).
Resynchronize side windows (
page 198).