Bulb Mercury Mountaineer 1998 Owner's Manuals

WARNING LIGHTS AND CHIMES
Check engine
Your vehicle is equipped with a
computer that monitors the
engine's emission control system.
This system is commonly known as
the On Board Diagnostics System
(OBD II). This OBD II system
protects the environment by
ensuring that your vehicle
continues to meet government
emission standards. The OBD II
system also assists the service
technician in properly servicing
your vehicle.
TheCheck Engineindicator light
illuminates when the ignition is
first turned to the ON position to
check the bulb. If it comes on after
the engine is started, one of the
engine's emission control systems
may be malfunctioning. The light
may illuminate without a
driveability concern being noted.
The vehicle will usually be drivable
and will not require towing.
C
012345
6
RPMx1000
ABS!BRAKE
CHECK
ENGINE
FUEL
RESET
EFH
H
H
PRN D 2 1THEFT
SPEED
CONT
4WD
HIGH
4WD
LOW
O/D
OFFL
L
10MPH 205060
70
304080
90
km/h
0 0 0
10 100
1
20
1
0 0 0 0 0 0406080100
120
140
160
180
20
DOOR
AJAR
CHECK
GAGE
CHECK
ENGINE
Instrumentation
6

Brake system warning
Momentarily illuminates when the
ignition is turned ONand the
engine is off. Also illuminates when
the parking brake is engaged.
Illumination after releasing the
parking brake indicates low brake
fluid level.
Anti-lock brake system (ABS)
Momentarily illuminates when the
ignition is turned on and the
engine is off. If the light remains
on, continues to flash or fails to
illuminate, have the system
serviced immediately.
Turn signal
Illuminates when the left or right
turn signal or the hazard lights are
turned on. If one or both of the
indicators stay on continuously,
check for a burned-out turn signal
bulb. Refer toExterior bulbsin
theMaintenance and care
chapter.
High beams
Illuminates when the high beam
headlamps are turned on.
!
BRAKE
ABS
Instrumentation
9

not pass the I/M test with the
ªcheck engine/service engine soonº
light on.
If the vehicle's powertrain system
or its battery has just been
serviced, the OBD-II system is
reset to a ªnot ready for I/M testº
condition. To ready the OBD-II
system for I/M testing, a minimum
of 30 minutes of city and highway
driving is necessary as described
below:
²First, at least 10 minutes of
driving on an expressway or
highway.
²Next, at least 20 minutes driving
in stop and go, city type traffic
with at least four idle periods.
Allow the vehicle to sit for at least
eight hours without starting the
engine. Then, start the engine and
complete the above driving cycle.
The engine must warm up to its
normal operating temperature.
Once started, do not turn off the
engine until the above driving
cycle is complete.
EXTERIOR BULBS
Replacing exterior bulbs
Check the operation of the
following lamps frequently:
²headlamps
²foglamps
²high-mount brakelamp
²brakelamps
²turn signals
Maintenance and care
190

²license plate lamp
²tail lamps
²back-up lamps
Do not remove lamp bulbs unless
they can be replaced immediately
with new ones. If a bulb is
removed for an extended period of
time, contaminants may enter the
lamp housings and affect lamp
performance.
Replacing headlamp bulbs
Handle a halogen
headlamp bulb carefully
and keep out of children's reach.
Grasp the bulb only by its plastic
base and do not touch the glass.
The oil from your hand could
cause the bulb to break the next
time the headlamps are
operated.
If the bulb is accidentally
touched, it should be cleaned
with rubbing alcohol before
being used.
To remove the headlamp bulb:
1. Make sure headlamp switch is in
OFF position, then open the hood.
If you are replacing the driver side
headlamp, unclip the electronic
module on the right side of the
battery and move it out of the way.
2. Locate the headlamp bulb
through the hole in the upper
radiator support assembly.
Maintenance and care
191

3. Disconnect the electrical
connector from the bulb by pulling
the connector rearward.
4. Remove the bulb retaining ring
by rotating it counterclockwise
(when viewed from the rear) about
an eighth of a turn to free it from
the bulb socket, and by sliding the
ring off the plastic base. Keep the
ring because it will be used again
to retain the new bulb.
5. Remove the old bulb from its
socket by gently pulling it straight
back out of the socket. Do not turn
the bulb while removing it.
To install the new bulb:
1. With the flat side of the bulb's
plastic base facing upward, insert
the glass end of the bulb into the
socket. You may need to turn the
bulb left or right to line up the
grooves in the plastic base with
the tabs in the socket. When the
grooves are aligned, push the bulb
into the socket until the plastic
base contacts the rear of the
socket.
2. Slip the bulb retaining ring over
the plastic base until it contacts
the rear of the socket by rotating it
clockwise until you feel a ªstop.º
Maintenance and care
192

3. Push the electrical connector
into the rear of the plastic base
until it snaps, locking it into
position.
4. Turn the headlamps on and
make sure they work properly. If
the headlamp was correctly aligned
before you changed the bulb, you
should not need to align it again.
Bulb specifications
Function Number of bulbs Trade number
Park/turn lamps
(front)4
3156 NAK
Headlamps 2 9007
Rear stop/tail lamps 2 3157K
Rear turn lamps 2 3156K
Rear license plate
lamps2
3156
Backup lamp 2 3156K
Rear/turn/sidemarker 2 916NA
Cargo lamp 1 211-2
Interior overhead lamp 1 912 (906)
Front door courtesy
lamp1
168
Map lamps 2 168 (T10)
Ashtray lamp 1 161
To replace all instrument panel lights - see your dealer.
Maintenance and care
193

Air bag supplemental restraint
system ..........................................73
and child safety seats ..............75
description ................................74
disposal ......................................78
indicator light ...........................77
passenger air bag .....................76
Air conditioning
manual heating and air
conditioning system .......18,21,23
Air suspension
description ..............................103
All wheel drive (AWD) .............118
Ambulance packages ....................3
Anti-lock brake system (ABS)..101
Anti-theft system ........................55
Autolamp system (see
Headlamps) .................................38
Automatic dimming mirror ...37,38
Battery .......................................173
voltage gauge ............................14
Brake fluid
checking and adding ..............162
Brakes ........................................100
anti-lock ...................................100
anti-lock brake system (ABS)
warning light ...........................101
fluid, checking and adding ....162
Brake-shift interlock .................104
Break-in period .............................2
Bulbs, replacing ........................190
headlamps ...............................191
specifications ..........................193
Cargo cover ............................44,45
Changing a tire .........................144
Child safety seats ........................81
built-in child seat ......86,87,91,92
Childproof locks ..........................41
Chime
headlamps on ............................12
Cleaning your vehicle ...............196
built-in child seat ...................201engine compartment ..............197
fabric ........................................200
instrument panel ....................200
plastic parts ............................199
safety belts ..............................201
tail lamps .................................200
washing ....................................196
waxing .....................................196
wheels ......................................199
windows ..................................203
woodtone trim ........................203
Compass, electronic ....................35
calibration .................................37
set zone adjustment .................36
Control trac 4WD system .........111
Controls .......................................42
Defrost
rear window ..............................24
Driving under special
conditions ...........................115,120
high water ........................115,120
slippery roads ....116,117,121,122
Emission control system ..........187
Engine ........................................209
service points ...................156,157
Engine block heater ...................97
Engine coolant
checking and adding ..............164
disposal ....................................166
refill capacities ........................167
Engine oil ...........................158,161
changing oil and oil filter .......161
checking and adding .......158,160
Exhaust fumes ............................98
Floor mats ...................................43
Foglamps .....................................16
Four-Wheel Drive vehicles
control trac ........................25,111
special driving
instructions ......................113,114
Fuel
calculating fuel economy .......187
Index
213