radio Mercury Mystique 1996 Owner's Manuals

42
[ST04400(ALL)05/94]
ACCESSORY allows some of your vehicle's electrical accessories
to operate while the engine is not running. For example, you
can use ACCESSORY to turn on the radio without starting the
engine.
*
[ST04425(ALL)05/95]
ON allows you to test your vehicle's warning lights (except the
brake system warning light) to make sure they work before you
start the engine. The key returns to the ON position once the
engine is started and remains in this position while the engine
runs.
*
[ST04450(ALL)03/95]
START cranks the engine. Release the key once the engine starts
so that you do not damage the starter. The key should return to
ON when you release it. The START position also allows you to
test the brake warning light.
%*
[ST04500(ALL)02/95]
Removing the Key From the Ignition
*
[ST04600(ALL)05/94]
Procedures for removing your key from the ignition vary,
depending on whether your vehicle has an automatic or manual
transaxle.
*
[ST04700(ALL)04/94]
If your vehicle has an automatic transaxle:
*
[ST04800(ALL)06/92]1.
Put the gearshift lever in P (Park).
*
[ST04900(ALL)01/95]2.
Set the parking brake fully.
[ST05000(ALL)05/94]3.
Rotate the ignition key to the LOCK position.
[ST05100(ALL)02/95]4.
Remove the key from the ignition.
*
[ST05200(ALL)04/94]
If your vehicle has a manual transaxle:
*
[ST05300(ALL)06/92]1.
Put the gearshift lever in 1 (First).
*
[ST05400(ALL)01/95]2.
Set the parking brake fully.
[ST05701(ALL)05/94]3.
Rotate the ignition key to the LOCK position.
[ST05801(ALL)02/95]4.
Remove the key from the ignition.
File:cdstz.ex
Update:Fri Feb 23 11:08:15 1996

60
*
[LG07650(ALL)03/95]
Check Engine Warning Light
*
[LG07750(ALL)05/95]
The Powertrain On-Board Diagnostic II (OBD II) system consists
of the hardware and software necessary to monitor the
operation of the powertrain. The OBD II system is designed to
check the function of the vehicle's powertrain control system
during normal operation. If an emission problem is detected, the
Check Engine Warning Light (in the cluster) is turned on.
*
[LG07800(ALL)05/95]
Modification or additions to the vehicle may cause incorrect
operation of the OBD II system. Additions such as burglar
alarms, cellular phones, and CB radios must be carefully
installed. Do not install these devices by tapping into or running
wires close to powertrain control system wires or components.
[LG07850(ALL)03/95]
6 pica art:0000640-B*
[LG07900(ALL)05/95]
This light comes on briefly when you turn the ignition to the
ON position, but should turn off when the engine starts. If the
light does not come on when you turn the ignition to the ON
position or if it comes on and stays on when you are driving,
have your vehicle serviced as soon as possible. This indicates a
possible problem with one of the engine's emission control
systems.You do not need to have your vehicle towed in.
*
[LG07950(ALL)05/95]
If the light turns on and off at one (1) second intervals while
you are driving the vehicle, it means that the engine is
misfiring. If this condition persists, damage could occur to the
engine or catalytic convertor. Have your vehicle serviced at the
first opportunity. You do not need to have your vehicle towed
in.
File:cdlgz.ex
Update:Fri Feb 23 11:08:00 1996

67
Instrument Panel Controls
*
[IP00310(ALL)01/95]
The instrument panel (dashboard) on your vehicle is divided
into several different sections. The illustrations on the following
pages show the major parts of the instrument panel that are
described in this chapter. Some items shown may not be on all
vehicles.
[IP00400(ALL)05/95]
The main controls for the climate control system, clock, and
radio are on the instrument panel.
*
[IP00420(ALL)03/95]
Clean the instrument panel lens and woodtone trim with a soft
cloth and a glass cleaner. Do not use paper towel or any
abrasive cleaner to clean either the lens or the woodtone trim as
these may cause scratches.
%*
[IP00430(ALL)05/95]
NOTE: Any cleaner or polish that increases the gloss (shine)
of the upper part of the instrument panel should be
avoided. The dull finish in this area is to help protect
the driver from undesirable windshield reflection.
File:cdipz.ex
Update:Fri Feb 23 11:07:15 1996

Instrument Panel Controls
69
*
[IP00500(ALL)01/95]
The Climate Control Systems
[IP00625(ALL)01/95]
Your vehicle has one of the following:
[IP00800(ALL)02/94]
n
Heating Only System (Without Air Conditioning)
*
[IP00900(ALL)02/95]
n
Heating and Air Conditioning System
*
[IP01100(ALL)09/89]
If you are not sure which system your vehicle has, see the
diagrams on the following pages.
[IP01201(ALL)03/95]
Heating Only System
[IP01220(ALL)05/94]
The control for your heater system is located at the center of the
instrument panel below the radio. The heater will operate only
when the ignition key is turned to the ON position. Your heater
will heat and/or ventilate your vehicle interior depending on
the function selector knob position and temperature you select.
The function selector knob allows you to select heating or
ventilation and determine where the air will be directed. The
temperature control knob setting determines the temperature of
the air that flows into the vehicle.
[IP01275( Z)03/95]
10-1/2 pica
art:0001301-A
The control for the heating only system
File:cdipz.ex
Update:Fri Feb 23 11:07:15 1996

Steering Column Controls
85
*
[SC07400(ALL)03/91]
Speed Control (If equipped)
*
[SC07500(ALL)06/95]
If your vehicle has speed control, you can automatically
maintain a constant speed at or above 30 mph (50 km/h).
*
[SC07550(ALL)05/95]
Use of radio transmitting equipment that is not Federal
Communications Commission (FCC) or in Canada the Canadian
Radio and Telecommunications Commission (CRTC) approved
may cause the speed control to malfunction. Therefore, use only
properly installed FCC (CRTC in Canada) approved radio
transmitting equipment in your vehicle.
*
[SC07650(ALL)03/95]
NOTE: Do not shift to N (Neutral) when using the speed
control. This will cause the engine to overspeed.
*
[SC07675(ALL)05/95]
RWARNING
Do not use the speed control in heavy traffic or on roads
that are winding, slippery, or unpaved.
[SC07700(ALL)05/94]
10-1/2 pica
art:0000262-D
The speed control switches on the steering wheel
File:cdscz.ex
Update:Fri Feb 23 11:06:33 1996

Features
95
*
[FV03300(ALL)11/93]
NOTE: The operating range of the remote entry system can
also be affected by weather conditions (such as very
cold temperatures) or structures around the vehicle
(buildings, other vehicles, radio towers, etc.). Typical
operating range will allow you to be up to 33 feet (10
meters) away from your vehicle.
[FV03400(ALL)05/94]
7-1/2 pica art:0001315-A
Replacing the batteries
*
[FV03500(ALL)02/95]
The transmitter can be snapped apart to replace the batteries by
twisting a thin coin between the two halves of the transmitter.
DO NOT TAKE THE FRONT PART OF THE TRANSMITTER
APART. When installing the new batteries, be sure to place the
positive (+) side down as marked. Snap the two halves back
together.
%*
[FV03600(ALL)02/95]
Replacement/additional transmitters
*
[FV03700(ALL)02/95]
In the event a transmitter is lost, return the remaining
transmitters to your dealer for reprogramming of your remote
entry system. This is necessary to prevent further unauthorized
use of the lost transmitter.
*
[FV03800(ALL)02/95]
Additional transmitters may be purchased from your dealer
(remote entry system will work with up to four transmitters).
Return your existing transmitters to your dealer so the remote
entry system can be reprogrammed with your new and existing
transmitters.
File:cdfvz.ex
Update:Fri Feb 23 11:06:10 1996

113
Electronic Sound Systems
[AS01100(ALL)04/94]
33-1/2 pica
art:0060657-A
Compact Disc Radio
File:cdasz.ex
Update:Fri Feb 23 11:04:59 1996

114
%*
[AS01125(ALL)05/95]
Compact Disc Radio
*
[AS01150(ALL)05/95]
The Compact Disc Radio combines the Electronic Stereo Radio
with the Ford Compact Disc Player.
*
[AS01200(ALL)04/95]
Using the Controls on Your New Radio/CD Player
*
[AS01300(ALL)04/95]
Most of the features of this unit work for both radio and CD
operation. Also, some of the knobs and buttons control several
different functions, so be sure to read all of the operating
instructions carefully.
*
[AS01400(ALL)04/95]
How to turn the radio on and off
*
[AS01500(ALL)04/95]
Press the ªPOWERº button to turn the radio on. Press it again
to turn it off.
*
[AS01600(ALL)04/95]
How to adjust the volume
*
[AS01700(ALL)05/95]
Press the (+/±) side of the ªVOLº button to increase/decrease
the volume. Bars illuminate in the display to show the relative
volume level.
*
[AS01800(ALL)04/95]
NOTE: If the volume level is set above a certain listening
level when the ignition switch is turned off, when the
ignition switch is turned back on, the volume will
come back to a ªnominalº listening level. However, if
the radio power is turned off (with the ªPOWERº
button), the volume will remain in the position it was
set at when radio power is switched back on.
*
[AS01900(ALL)04/95]
Selecting the AM or FM frequency band
*
[AS02000(ALL)04/95]
Push the ªAM/FMº button to select the desired frequency band.
When in the radio mode, pushing the button more than once
will alternate between AM, FM1 and FM2. These functions are
used with the station memory buttons described underHow to
tune radio stations.
File:cdasz.ex
Update:Fri Feb 23 11:04:59 1996

Electronic Sound Systems
115
%*
[AS02100(ALL)05/95]
How to tune radio stations
*
[AS02200(ALL)04/95]
There are four ways for you to tune in a particular station. You
can manually locate the station using the ªSCAN/TUNEº
button, ªSEEKº the station, ªSCANº to the station or select the
station by using the memory buttons, which you can set to any
desired frequency. These four methods are described below.
*
[AS02300(ALL)04/95]
n
Using the ªSCAN/TUNEº button to manually tune
*
[AS02400(ALL)04/95]
You can change the frequency up or down one increment at
a time (FM changes in increments of 200kHz; AM changes in
increments of 10kHz) by first pressing the ªSCAN/TUNEº
button twice (display shows ªTUNEº), then Ðwithin
approximately five secondsÐ pressing and releasing either
the top
aor bottom
bhalf of the ªSEEKº button. To
change frequencies quickly, press andhold downeither the
top or bottom half of the ªSEEKº button. While you are
manually tuning, the display will show a blinking ªMº.
*
[AS02500(ALL)04/95]
Manual tuning adjusts your radio to any allowable broadcast
frequency, whether or not a station is present on that
frequency. (SeeAll About Radio Frequenciesin this section.)
*
[AS02600(ALL)04/95]
n
Using the ªSEEKº function
*
[AS02700(ALL)04/95]
This feature on your radio allows you to automatically select
listenable stations up or down the frequency band. Press the
top
ahalf of the ªSEEKº button to select the next listenable
station up the frequency band. Press the bottom
bhalf of
the button to select the next listenable station down the
frequency band. By pressing and holding the button,
listenable stations can be passed over to reach the desired
station.
File:cdasz.ex
Update:Fri Feb 23 11:04:59 1996

116
*
[AS02800(ALL)04/95]
n
Using the ªSCAN/TUNEº button to scan radio stations
*
[AS02900(ALL)04/95]
Pressing the ªSCAN/TUNEº button once enters the scan
mode (display will indicate ªSCNº). Pushing the top
ahalf
of the ªSEEKº button will begin the scan mode up the
frequency band, stopping on each listenable station for
approximately five seconds. Pushing the bottom
bhalf of
the ªSEEKº button will begin the scan mode down the
frequency band, again stopping on each listenable station for
approximately five seconds.
*
[AS03000(ALL)04/95]
To stop the scan mode on the presently sampled station
press the ªSCAN/TUNEº button again.
*
[AS03200(ALL)04/95]
n
Setting the Station Memory Preset buttons
*
[AS03300(ALL)02/95]
Your radio is equipped with 6 station memory buttons.
These buttons can be used to select up to 6 preset AM
stations and 12 FM stations (6 in FM1 and 6 in FM2).
*
[AS03400(ALL)04/95]1.
Select a band, then select a frequency.
*
[AS03600(ALL)04/95]2.
Press one of the memory buttons and hold the button until
the sound returns. That station is now held in memory on
that button.
*
[AS03700(ALL)04/95]3.
Follow the two steps above for each station memory preset
button you want to set.
*
[AS03850(ALL)04/95]
NOTE: If the vehicle's battery is disconnected, the clock and
station memory preset buttons (if programmed in auto
mode) will need to be reset.
[AS04150(ALL)02/95]
n
Using the Automatic Memory Store feature
*
[AS04250(ALL)05/95]
With Auto Memory Store, you can continually set strong
stations into your memory buttons without losing your
existing memory presets, which is especially handy while
traveling. Your radio will automatically set your memory
buttons to the strong local stations so you don't have to
continually manually tune to existing stations.
File:cdasz.ex
Update:Fri Feb 23 11:04:59 1996