stop start Mercury Villager 1996 Owner's Manuals

Starting Your Villager
59
*
[ST04500(ALL)01/93]
RWARNING
Do not leave children, unreliable adults, or pets alone in
your vehicle. They could accidentally injure themselves
or others through inadvertent operation of the vehicle.
Further, on hot, sunny days, temperatures in a closed
vehicle could quickly become high enough to cause
severe and possibly fatal injuries to people as well as
animals.
%*
[ST04600(ALL)03/95]
Fuel-Injected Engines
*
[ST04700(ALL)03/95]
When starting a fuel-injected engine,the most important thing
to remember is to avoid pressing down on the accelerator
before or during starting. Only use the accelerator when you
have problems getting your vehicle started. SeeStarting Your
Enginein this chapter for details about when to use the
accelerator while you start your vehicle.
[ST04750(ALL)02/95]
Starting Your Vehicle
%*
[ST04800(ALL)05/94]
Preparing to Start Your Vehicle
*
[ST04900(ALL)05/95]
RWARNING
Do not start your vehicle in a closed garage or other
enclosed area. Never sit in a stopped vehicle for more
than a short period of time with the engine running.
Exhaust fumes are toxic. SeeGuarding Against Exhaust
Fumesin this chapter for more instructions.
*
[ST04950(ALL)01/93]
Before you start your vehicle, always:
*
[ST05000(ALL)01/93]1.
Make sure you and all your passengers buckle your safety
belts. SeeSafety beltsin the Index for more details.
*
[ST05100(ALL)03/95]2.
Make sure the headlamps and other accessories are turned
off when starting.
File:04vxstn.ex
Update:Mon Jun 3 08:20:06 1996

Starting Your Villager
61
*
[ST07200(ALL)04/94]
For a warm engine:
*
[ST07300(ALL)04/95]
n
Do not hold the key in the START position for more than
five (5) secondsat a time. If the engine does not start within
five (5) seconds on the first try, turn the key to the OFF
position. Wait a few seconds after the starter stops, then try
again.
*
[ST07350(ALL)05/95]
Whenever you start your vehicle, release the key as soon as the
engine starts. Excessive cranking could damage the starter or
flood the engine.
*
[ST07360(ALL)02/95]
After you start the engine, let it idle for a few seconds.Keep
your foot on the brake pedaland release the parking brake.
Put the gearshift lever in gear, slowly release the brake pedal
and drive away in the normal manner.
*
[ST07370(ALL)02/95]
NOTE: Your vehicle has an interlock that prevents you from
shifting out of Park (P) unless your foot is on the
brake pedal.
%*
[ST07500(ALL)04/95]
If the engine does not start after two attempts:
*
[ST07600(ALL)04/95]1.
Turn the ignition key to the OFF position.
*
[ST07700(ALL)04/95]2.
Press the accelerator all the way to the floor and hold it.
*
[ST07800(ALL)04/95]3.
Turn the ignition key to the START position.
*
[ST07900(ALL)04/95]4.
Release the ignition key when the engine starts.
*
[ST08000(ALL)04/95]5.
Release the accelerator gradually as the engine speeds up.
Then drive away in the normal manner.
*
[ST08100(ALL)04/95]
If the engine still does not start, the fuel pump shut-off switch
may have been triggered. For directions on how to reset the
switch seeFuel Pump Shut-Off Switchlater in this chapter.
File:04vxstn.ex
Update:Mon Jun 3 08:20:06 1996

Starting Your Villager
63
*
[ST09000(ALL)01/93]
For best results, plug the heater in at least three hours before
you start your vehicle. Using the heater for longer than three
hours will not damage the engine, so you can leave it plugged
in all night to start your vehicle the following morning.
%*
[ST09005(ALL)02/95]
What To Do If The Engine Does Not Start
%*
[ST09010(ALL)02/95]
Fuel Pump Shut-Off Switch
*
[ST09015(ALL)03/95]
If the engine cranks but does not start or does not start after a
collision, the fuel pump shut-off switch may have been
triggered. The shut-off switch is a device intended to stop the
fuel pump when your vehicle has been involved in a substantial
jolt.
*
[ST09020(ALL)03/95]
Once the shut-off switch is triggered, you must reset the switch
by hand before you can start your vehicle.
[ST09025(ALL)02/95]
The fuel pump shut-off switch reset button is located below the
hood release handle.
[ST09030(ALL)02/95]
10-1/2 pica
art:0040048-C
Fuel pump shut-off switch reset button location
File:04vxstn.ex
Update:Mon Jun 3 08:20:06 1996

Starting Your Villager
65
*
[ST09400(ALL)02/95]
RWARNING
If you ever smell exhaust fumes of any kind inside your
vehicle, have your dealer inspect and fix your vehicle
immediately. Do not drive if you smell exhaust fumes.
These fumes are harmful and could kill you.
*
[ST09500(ALL)02/95]
Have the exhaust and body ventilation systems checked by a
qualified technician whenever:
*
[ST09600(ALL)02/95]
n
your vehicle is raised for service
*
[ST09700(ALL)02/95]
n
the sound of the exhaust system changes
*
[ST09800(ALL)02/95]
n
your vehicle has been damaged in an accident
*
[ST09900(ALL)02/95]
Improve your ventilation by keeping all air intake vents clear of
snow, leaves, and other objects.
*
[ST10000(ALL)03/95]
If the engine is idling while you are stopped in an open area
for long periods of time, open the windows at least one inch
(2.5 cm). Also, adjust the heating or air conditioning to bring in
outside air.
*
[ST10100(ALL)02/95]
Read the sectionClimate Control Systemsfor instructions on
bringing fresh outside air into your vehicle. Refer to the Index.
File:04vxstn.ex
Update:Mon Jun 3 08:20:06 1996

112
[IP11000(ALL)04/95]
To activate the rear washer, press the RR WASH switch. For a
constant spray, hold the switch for a few seconds. For less
washer fluid, press the switch once and release it. When you
activate the washer, the wiper will cycle twice and then stop.
*
[IP11050(ALL)04/95]
Do not activate the washer for longer than fifteen seconds
continuously. This could damage the washer pump system.
*
[IP11100(ALL)04/95]
Hazard Flasher Switch
*
[IP11150(ALL)04/95]
The hazard flasher is used to alert other drivers to hazardous
situations.
*
[IP11200(ALL)09/93]
The hazard flasher switch operates the same lamps as the turn
signal lever. When the hazard flasher is activated, all of these
lamps will flash on and off. The turn signal indicators cannot be
used when the hazard lamps are flashing. Operation of the
hazard flashers does not affect operation of the brakelamps.
*
[IP11300(ALL)12/93]
The flashers work even with the key out of the ignition. The
flashers will work for up to two hours when the battery is fully
charged and in good condition. They will not drain the battery
excessively. If the flashers run for longer than two hours or if
your battery is not fully charged, your battery may be drained
to the point where the vehicle will not start.
[IP11400(ALL)01/93]
The hazard flasher switch is located on the instrument panel to
the right of the instrument cluster.
*
[IP11500(ALL)09/93]
To use the hazard flasher:
*
[IP11600(ALL)02/94]1.
Push the HAZARD switch; you will see the turn signal
arrows flash.
*
[IP11700(ALL)09/93]2.
To stop the hazard flashers, push the HAZARD switch again.
File:06vxipn.ex
Update:Mon Jun 3 14:33:05 1996

Electronic Sound Systems
215
[AS11000(ALL)06/95]2.
Rewinding the tape
[AS11100(ALL)06/95]
To rewind the tape, press the ªREWº button. The ª
Xº
display blinks while the tape rewinds. The radio will
automatically begin playing until rewind is manually
stopped (by pushing the ªREWº button) or the beginning of
the tape is reached.
[AS11200(ALL)05/94]3.
Using the ªSEEKº function with a cassette tape
[AS11300(ALL)06/95]
While in the tape mode, push the right (
a) side of the
ªSEEKº button to seek forward to the next selection on the
tape. Push the left (
b) side of the ªSEEKº button to seek
the previous tape selection. The ªTAPEº display blinks.
*
[AS11400(ALL)11/93]
NOTE: If you want to restart a currently playing tape
selection, press the left (
b) side of the ªSEEKº button
after three seconds into the current selection.
[AS11500(ALL)06/95]4.
Using the ªSCANº button to scan cassette selections
[AS11600(ALL)06/95]
Press the ªSCANº button to enter the scan mode (display
blinks ªSCº) to begin the forward scan mode on the tape
currently playing, stopping on each tape selection for a
five-second sampling.
[AS11650(ALL)06/95]
The scan mode continues to the other side of the tape after
one side of the tape has been played completely.
[AS11800(ALL)06/95]
To stop the scan mode on the presently sampled tape
selection, press the ªSCANº button again, or press ªTAPE,º
ªCDº (if equipped), ªTUNE,º or ªSEEK.º
[AS11900(ALL)03/93]
Reversing the direction
[AS12000(ALL)06/95]
The alternate track of the tape can be selected anytime by
pressing the ªSIDE 1-2º button.
File:10vxasn.ex
Update:Mon Jun 3 14:57:29 1996

230
[DR01600(ALL)09/93]Shift-lock Safety Feature
[DR01700(ALL)04/95]Your vehicle has a special shift-lock safety feature which
prevents you from shifting out of P (Park) without the brake
pedal depressed. To shift the transaxle out of the P (Park)
position, the ignition must be in the ON position and your foot
must be pressing on the brake pedal.
*[DR01800(ALL)04/95]If the shift lever cannot be moved from the P (Park) position
with the brake pedal depressed:
*[DR01900(ALL)01/93]1.Shut the engine off and remove the ignition key.
*[DR02000(ALL)01/93]2.Apply the parking brake.
*[DR02100(ALL)01/93]3.Reinsert the ignition key and turn it clockwise to the first
position (OFF).
*[DR02200(ALL)04/95]4.Depress the brake pedal, move the gearshift lever to N
(Neutral) and start the engine.
*[DR02290(ALL)06/95]If you need to shift out of P (Park) by using the alternate
procedure described above, it is possible that a fuse has blown
and that your brakelamps may also not be functional. Please
refer to the chapter titledServicing Your Villagerin this Owner
Guide for instructions on checking and replacing fuses.
*[DR02300(ALL)05/95]R WARNING
DO NOT DRIVE YOUR VEHICLE UNTIL YOU VERIFY
THAT THE BRAKELAMPS ARE WORKING.
%*[DR02500(ALL)06/92]Backing Up
*[DR02600(ALL)06/95]Before shifting into or out of R (Reverse), you should always
come to a complete stop.
File:11vxdrn.ex
Update:Tue Jun 4 11:42:50 1996

232
*
[DR03700(ALL)02/95]
The transaxle will be in the ªoverdrive onº mode when the
vehicle is started even if the O/D OFF mode was selected when
the vehicle was last shut off.
[DR03800(ALL)04/94]
If your vehicle is on an extremely slippery surface, the
Electronic Transaxle Control Module may receive a signal
indicating a rapid increase or decrease in wheel speed. If the
module detects this condition, it will limit the transaxle
operation to Third gear and Reverse. This reduces tire slippage
and protects the transaxle. The transaxle will operate normally
in Reverse, but will lack power during acceleration in Drive. If
this happens, stop your vehicle as soon as possible and turn the
ignition off for 3 seconds. Restart the vehicle. If the condition
still exists, contact your dealer as soon as possible.
*
[DR03900(ALL)04/95]
NOTE: If the O/D OFF indicator light is flashing on and off
repeatedly when the vehicle is started, there is a
transaxle electronic system malfunction. Contact your
dealer as soon as possible.
*
[DR04000(ALL)06/95]
When to use 2 (Second)
[DR04100(ALL)01/93]
Use Second (2) when driving on slippery roads or to provide
additional engine braking on downgrades. This position
provides Second gear operation only. Do not exceed 68 mph
(110 km/h) in this position.
*
[DR04200(ALL)06/95]
When to use 1 (First)
[DR04300(ALL)01/93]
Use First (1) to provide maximum engine braking on steep
downgrades. Upshifts from First can be made by manually
shifting to Second (2) or Overdrive (D). First (1) gear provides
only first gear operation. If you select First while driving at
higher speeds, the transaxle will shift to Second (2), and then
shift back to First (1) after the vehicle decelerates to the proper
speed. Do not exceed 35 mph (56 km/h) in this position.
File:11vxdrn.ex
Update:Tue Jun 4 11:42:50 1996

Driving Your Villager
235
*
[DR06800(ALL)01/93]
Four-Wheel Anti-lock Brakes
*
[DR06900(ALL)01/94]
The Anti-lock Brake System (ABS) prevents wheels from
completely locking up by automatically releasing and
re-applying the brakes. During ABS braking, slight brake pedal
pulsations may be felt on the driver's foot. These pulsations
represent the rapid cycling of the ABS valves. The pedal
pulsations are considered normal ABS operation, and will stop
when normal braking is resumed or when the vehicle comes to
a stop.
%*
[DR07000(ALL)12/93]
During ABS activation, a mechanical noise may be heard as the
ABS system cycles. This is normal ABS operation.
*
[DR07100(ALL)12/93]
The ABS system has self-check capabilities. The system turns on
the ABS warning light each time you start the engine. After the
engine is started and the ABS warning light turns off, the
system performs another test the first time the vehicle reaches
4 mph (6 km/h). A mechanical noise may be heard as the ABS
system performs a self test. This is a normal part of the self test
feature. If a malfunction is found during this check, the ABS
warning light will come on.
*
[DR07200(ALL)12/93]
You should always be careful when braking, even if your
vehicle has the ABS system. Heavy braking on roads with loose
surfaces such as snow or gravel, or roads with severe pavement
irregularities could also cause you to lose control of your
vehicle.
*
[DR07300(ALL)05/95]
RWARNING
If the anti-lock brake system warning light remains on or
comes on while driving, have the braking system checked
by a qualified service technician as soon as possible.
*
[DR07310(ALL)06/95]
NOTE: If a fault occurs in the anti-lock system, and the brake
warning light is not lit, the anti-lock system is
disabled but normal brake function remains
operational.
File:11vxdrn.ex
Update:Tue Jun 4 11:42:50 1996

Driving Your Villager
251
*
[DR19600(ALL)01/93]
Trailer Brakes
*
[DR19700(ALL)01/93]
Separate trailer brakes are required on most trailers weighing
over 1,500 lbs. (680 kg).
*
[DR19800(ALL)05/95]
RWARNING
Do not connect a trailer's hydraulic brake system directly
to your vehicle's brake system. Your vehicle may not
have enough braking power and your chances of having
a collision greatly increase.
*
[DR19900(ALL)01/93]
Trailer Lamps
*
[DR20000(ALL)01/93]
Make sure your trailer lamps conform to federal and local
regulations.
*
[DR20100(ALL)01/93]
Class I Trailer Tow electrical wiring provides two circuits (right
hand and left hand) to operate trailer stop/turn tail lamps. Each
stop/turn circuit will operate one combination stop/turn light
bulb (# 1157, 3157, 2357, or 3357) on the trailer. Never add more
than one trailer light bulb to one circuit.
*
[DR20200(ALL)05/95]
RWARNING
Always replace a fuse with one that has the specified
amperage rating. Using a fuse with a higher amperage
rating can cause severe wire damage and could start a
fire.
[DR20210(ALL)04/94]
Trailer Tow Module (If equipped)
[DR20220(ALL)06/94]
The trailer tow module on your vehicle (if equipped) allows
turn/stop lamp control on a trailer being towed by your
vehicle.
[DR20230(ALL)04/94]
The trailer tow package includes:
[DR20240(ALL)04/94]
n
trail or tow module which draws power from the vehicle
stop lamp fuse
File:11vxdrn.ex
Update:Tue Jun 4 11:42:50 1996