door lock Mercury Villager 1998 s User Guide

Remote Keyless Entry System (If equipped)
If you have chosen the remote keyless entry system option for
your vehicle, you can lock or unlock the doors and liftgate without
using a key. This option will allow you to open your vehicle
using a remote transmitter from distances of up to 49 feet (15
meters) away. The remote feature will operate only when the
ignition is in the OFF position.
The transmitter can unlock the driver's door, unlock all doors,
lock all doors, and activate the vehicle's anti-theft system (if
equipped). It is designed to be carried with your vehicle key.
By pressing the UNLOCK button on the transmitter once, you can
unlock the driver door. Pressing the UNLOCK button a second
time within six (6) seconds of unlocking the driver door will unlock
the other doors. The interior lamp will turn on and stay on for
thirty (30) seconds.
By pressing the LOCK button on the transmitter once, all the
doors will lock, the parking lamps flash twice and the horn chirps.
When the LOCK button is pushed with all the doors locked,
the parking lamps flash twice and the horn chirps to confirm that
the doors are already locked.
Remote keyless entry transmitter
Controls and Features
11 3

ID Code Programming Procedure
NOTE: All transmitters must be programmed (or
reprogrammed) at the same time. If the programming
mode is entered and the transmitters are not programmed
(or reprogrammed) at the same time, they will not
operate with the system.
1. Enter vehicle and close and lock all doors.
2. Insert and remove key from ignition six times within ten (10)
seconds. The instrument panel lights will flash twice.
3. Turn ignition key to the ACC position.
4. Press the LOCK button on the remote transmitter once.
5. To enter additional remote controllers (including the original),
unlock, then lock the driver door using the power door lock
switch.
6. Press the LOCK button on a new remote transmitter. The
instrument panel lights will flash twice, indicating code is
entered.
7. Repeat steps 5 and 6 as needed (up to four remote transmitters
may be programmed).
Anti-Theft System (If equipped)
This system helps protect your vehicle against break-ins or theft
by monitoring all doors, the hood and the liftgate lock
cylinder.
When an unauthorized entry occurs, the system triggers and will:
mflash the headlamps and hazard lamps
mhonk the horn
mdisable the starting circuit to prevent the vehicle from being
started
11 6

To arm the system
1. Remove the key from the ignition.
2. Lock the doors by using either the power door lock switch or
by turning the key in either the driver or passenger door lock
cylinder. The parking lights will flash and the horn chirps
to let you know that the system has been armed. The anti-theft
indicator light on the right side of the steering wheel will
light and remain on.
NOTE: If your vehicle is equipped with a factory installed
remote keyless entry system, the system can be armed
by closing all the doors and pressing the LOCK
button on the remote transmitter.
3. Close all doors. The anti-theft indicator light will stay on for
approximately 30 seconds and then flash once every 2.5
seconds.
Anti-theft indicator light
Controls and Features
11 7

NOTE: Be sure to close all the doors completely. If the doors
are not completely closed, the alarm indicator light will
remain on steadily. The anti-theft system is armed
only when the anti-theft indicator light remains on
steadily for approximately 30 seconds after the last door
is closed, and then flashes every 2.5 seconds.
Disarming an untriggered anti-theft system
Unlock either door with the door key or by pressing the
UNLOCK button on the remote keyless entry transmitter (if
equipped). This will disarm the system. When you unlock the door
with the key, make sure you fully rotate the key in the lock. If
you do not, the system may not disarm, and will trigger when a
door is opened.
If the system is armed and you remain in your vehicle, simply
insert the key into the ignition and turn it to ACC. This disarms the
system and allows you to open the door to exit without
triggering the system. Remember to rearm the system by using
the power door lock or the remote transmitter (if equipped) to lock
the doors.
The remote keyless entry system is designed to work with the
factory installed anti-theft system. It may not work with other
anti-theft systems.
Triggering the anti-theft system
The armed system will be triggered if:
many door is opened without using the door key or the remote
keyless entry transmitter (if equipped)
mthe liftgate is opened or unlocked
mthe hood is opened
11 8

Disarming a triggered anti-theft system
The alarm can be disarmed by:
munlocking the driver or passenger doors
munlocking the doors with the remote keyless entry transmitter
(if equipped)
mputting the key in the ignition and turning it to the ACC
position
NOTE: The flashing lights and honking horn will shut off
automatically within 2 minutes 30 seconds after the
system is triggered. It will trigger again if another
intrusion occurs. However, the starter circuit remains
disabled until the system is disarmed.
NOTE: Factory installed remote keyless entry systems will only
operate with the ignition in the OFF position.
Controls and Features
11 9

WARNING
Each seating position in your vehicle has a specific safety
belt assembly which is made up of one buckle and one
tongue that are designed to be used as a pair. 1) Use the
shoulder belt on the outside shoulder only. Never wear
the shoulder belt under the arm. 2) Never swing it around
your neck over the inside shoulder. 3) Never use a
single belt for more than one person.
WARNING
Never drive or ride with a twisted or jammed safety belt.
If you cannot untwist or unjam the safety belt, see the
nearest qualified technician immediately.
WARNING
Children should always ride with the seatback in the fully
upright position.
WARNING
Lock the doors of your vehicle before driving to lessen the
risk of the door coming open in a collision.
130

Combination Lap and Shoulder Belts
While your vehicle is in motion, the combination lap and
shoulder belt adjusts to your movement. However, if you brake
hard, turn hard, or if your vehicle receives an impact of 5 mph (8
km/h) or more, the lap and shoulder belt locks and helps to
reduce your forward movement.
After you get into your vehicle, close the door and lock it. Then
adjust the seat to the position that suits you best.
To fasten the belt, pull the combination lap and shoulder belt
from the retractor so that the shoulder portion of the belt crosses
your shoulder and chest. Be sure the belt is not twisted. If it
is, remove the twist. Insert the belt tongue into the proper buckle
until you hear a snap and feel it latch. Make sure the tongue
is securely fastened to the buckle by pulling on tongue.
NOTE: Be sure to read and understandImportant Safety Belt
Informationat the beginning of this chapter.
Fastening the front seat combination lap and shoulder belt
Seating and Safety Restraints
131

Using the Automatic Locking Mode Retractor to Secure
a Child Safety Seat
Your vehicle is equipped with a dual locking mode retractor on
the shoulder belt portion of the combination lap/shoulder safety
belt for the front passenger seat and rear outer seats. The
automatic locking modemust be usedwhen installing a child
seat or infant carrier in the front passenger seat or rear outer seats.
To install a child safety seat or infant carrier, follow these steps:
1. Position the child seat or infant carrier in the vehicle seat. If you
are using the moveable third row seat in the third row
position, the passenger side second row bucket seat, or the
front passenger seat, slide the seat to the rearmost position.
2. Follow the child seat or infant carrier manufacturer's
instructions. Route the safety belt through the child seat or
infant carrier and insert the safety belt tongue into the buckle
until you hear and feel the latch engage. Be sure to follow
the child safety seat manufacturer's instructions for belt
routing. When using the seating position near the sliding door
on the two-passenger bench seat, be sure that the single
window tongue is attached to the auxillary buckle on the side
of the seat.
156

Installing the Two-Passenger Bench Seat
To replace the bench seat in its original position:
1. Make sure the area around the floor anchor positions is free
from obstruction.
2. With the seatback folded down, two people should lift the seat
into the vehicle.
3. Place the seat slightly behind the floor anchor positions and
catch the rear leg anchors into each anchor position.
4. Press down on the front of the seat to secure the front legs to
the two floor latch locks. Place the seatback in the upright
position.
5. Try to move the seat to be sure that it is securely fastened.
6. Always reattach the tongue into the auxiliary buckle mounted
to the sliding door side of the seat.
Labels have been provided on the side of the seat to remind you
of important safety precautions.
7. Replace any floor mats that were removed.
WARNING
Keep foreign objects out of the floor anchors. Objects in
the floor anchors could prevent front and rear seat legs from
engaging properly.
WARNING
Before sitting in the removable seats, make sure that the
seat legs are securely attached by the floor anchors.
186

WARNING
To prevent the vehicle from moving when you change a
tire, be sure the parking brake is set, then block (in both
directions) the wheel that is diagonally opposite (other
side and end of the vehicle) to the tire being changed.
WARNING
If the vehicle slips off the jack, you or someone else could
be seriously injured.
2. Remove the spare tire and jack. See previous section for
instructions on spare tire removal. The jack is located in the rear
storage compartment in the right door panel of the cargo
area. You will have to unfasten the jack before removing it as
shown in the illustration. The jack handle is in the tool kit
located behind the jack.
NOTE: All occupants should be out of the vehicle while it is
on the jack.
Roadside Emergencies
259