air condition MITSUBISHI 3000GT 1991 Owner's Manual

13-50FUEL SYSTEM - 0
n-vehicle Inspection of MPI Components
OPERATIONControl Relay Operation
l Drives the fuel pump during cranking and engine operation.
l
When the ignition switch is set to START, current flows from the ignition switch through the control relay
coil to ground. This turns on the control relay switch and drive power is supplied from the battery throughthe control relay switch to the fuel pump.
lWhile the engine is running, the engine control unit keeps the power transistor on and energizes the
control relay coil so that drive power is supplied to the fuel pump.
Fuel Pump Relay No. 2 Operation
lChange the fuel pump discharge in two stages by ON-OFF operation of the relay switch for fuel pumprelay No. 2.
lIf the amount of inlet air is small (the engine load is low), the engine control unit turns on the power
transistor to energize the coil of fuel pump relay No. 2, sending drive power to the fuel pump through the
resistor. If the amount of inlet air is large (the engine load is high), the engine control unit turns off thepower transistor to send drive power directly to the fuel pump without passing through the resistor.
INSPECTIONUsing Multi-use Tester
Function
ActuatortestItem No.
Operation
Check conditionCheck itemNormal condition
07Fuel pump isdriven to cir-l Engine crankingHold return hose withl Forced drive of fuelPulsation is felt
culate fuelfingers to feel pulsationpump
Check is made for aboveindicating fuel flow
two conditionsListen to pump operating
sound near fuel tankOperating sound isheard 2>
I/IIII
cFunctionItem No.Operation
Check conditionNormal condition
Actuatortest
13Turn the fuel pump relayNo. 2 from OFF to ONIgnition switch: ONOperating soundis heard.
HARNESS INSPECTION
k
J------ 7FUO953
lApply battery voltage to thecheckingterminal and operate the
Check the ground circuit of the fuel
pump.
l Connector: Disconnected
@I Harness side
connectorL-J
7FUO554
Repair the
harness.
@pJ-Ground)
J
1 TSB Revision

FUEL SYSTEM - On-vehicle Inspection of MPI Components13-55
INSPECTIONUsing Multi-use Tester

Function
Data readingtern No. Data display
12Sensor airvolume(frequency)
Check conditionEngine stateStandard value
l Engine coolant tem-
700 rpm (Idle)25-50 Hzperature: 80 to 95°C
(176 to 205°F)2,000 rpm70-IOOHzl Lights and accessories:OFFRacingFrequency increasesl Transaxle: Neutralwith racing(P range for vehiclewith AIT)l Steering wheel: Neutral
NOTEWhen the vehicle is new [within initial operation of about 500 km (300 miles)], the air flow sensor output frequency maybe about 10% higher.

Function
Data listItem No. Data displayCheck conditionsEngine conditionsStandard value
34Reset signall Engine warm up700 rpm (Idle)ON
condition2,000 rpmOFF
L;
FunctionItem No. Data display
Data list37Volumetric
efficiencyCheck conditionEngine stateStandard valuel Engine coolant tem-700 rpm (Idle)20-35%
perature: 80 to 95°C
(176 to 205°F)
l Lights, electric cooling2,000 rpm15-30%
fan and accessory opera-tion: OFFl Transaxle: NeutralRacingFrequency increases
(P range for vehiclewith racingwith &T)
l Steering wheel: Neutral
Using Oscilloscope(1) Run the engine at idle speed.
(2) Connect the probe to the oscilloscope pick-up point as
shown in the circuit diagram, and check the waveform.
Regular waveform
03A0203
TSB Revision

13-58FUEL SYSTEM - On-vehicle Inspection of MPI Components
INSPECTION
Using Multi-use Tester
FunctionItem No. Data displayCheck conditionIntake air temperatureStandard valued
Data reading13Sensorignition switch: ON orAt -20°C (-4°F)-20°C
temperatureengine running
At 0°C (32°F)0°C
At 20°C (68°F)20°C
At 40°C (104°F)40°C
At 80°C (176°F)80°C
HARNESS INSPECTION7FUO657
I
connector
7FUO6607FUO661
ITSB I
Check for continuity of the groundcircuit.l Connector: Disconnected
Repair the
harness.,
(@I3 - q ,
Measure the power supply voltage.l Connector: Disconnected
l Ignition switch: ON
Voltage
(V)4.5
- 4.9Repair the
harness.
@@J-@)
SENSOR INSPECTION
(1) Disconnect the air flow sensor connectors.
(2) Measure resistance between terminals @ and
@.
ITemperature [“C (“F)]IResistance (kfl)
I0 (32)I6.0
I20 (681I2.7
wisionI
d

FUEL SYSTEM - On-vehicle Inspection of MPI Components13-61
TROUBLESHOOTING HINTS
Hint 1 : If the barometric pressure sensor is faulty, poor driveability is caused at high altitude, in particular.
L
Hint 2: If the pressure indication of the barometric pressure sensor drops significantly during high speeddriving, check the air cleaner for clogging.
INSPECTIONUsing Multi-use Tester
Function
Data readingItem No.’ Data display
25
Check conditionAltitudeStandard value
Sensor
pressureIgnition switch: ON
At 0 m (0 ft.)760 mmHg
At 600 m (1,969 ft.)
710 mmHg
I/At 1,200 m (3,937 ft.)1660 mmHgI
At 1,800 m (5.906 ft.)610 mmHg
HARNESS INSPECTION
II
L
7FUO657
7FUO66:
Check for continuity of the ground
circuit.l Connector: Disconnected
Repair the
harness.
&@I - q ,
Measure the power supply voltage ofthe barometric pressure sensor.l Connector: Disconnected
l Ignition switch: ON
Voltaqe (V)4.8
- 5.2Repair theharness.
KgpJ-pJ,
Engine contraunit harnessside connects
Check for an open-circuit, or a short-circuit to ground between the enginecontrol unit and the barometric pres-,Y---,A
sure sensor.l
Air flow sensor connector: Dis-(OK) -+ kTOA
connectedlEngine control unit connector:
Disconnected
--I
Repair the
harness.

Jg
7FUO666
1 TSB Revision

id
LFUEL SYSTEM
- On-vehicle Inspection of MPI Components13-63
INSPECTIONUsing Multi-use Tester
LFunctionItem No. Data displayCheck condition
Coolant temperatureStandard valueData reading 21
SensorIgnition switch: ON or
At -20°C (-4°F)-20°C
temperatureengine operatingAt 0°C (32°F)0°C
HARNESS INSPECTION
Check for continuity of the groundcircuit.l Connector: Disconnected
Repair the---+ harness.

7FUO6682
Measure the power supply voltage.l Connector: Disconnected
@ Harness sidel Ignition switch: ON
7FUO669TSB Revision

13-66FUEL SYSTEM - 0n-vehicle Inspection of MPI Components
INSPECTIONUsing Multi-use Tester
FunctionItem No. Data displayCheck conditionThrottle valveStandard value‘d
Data reading14SensorIgnition switch: left ONvoltagefor 15 seconds or moreAt idle position300-1.000 mV
Open slowly
Increases withvalve opening
Open widely4.500-5.500 mV
HARNESS INSPECTIONl Connector: Disconnected
l
lgnrtion switch: ON
l Connector: Disconnected
connector
I
Engine controlCheck for an open-circuit, or a short-
unit harnesscircuit to ground between the engine
side connectorcontrol unit and the throttle positionsensor.
Throttle position sensor connec-
tor: Disconnected
Engine control unit connector:
DisconnectedRepair theB-3 harness.
km-8)
-z =6FU1243
[ TSB Revision

FUEL SYSTEM - On-vehicle Inspection of MPI Components
L
L
IGNITION SWITCH-ST
lgnitlon switch (ST)
I
Enaine control unit connector
7FUO653
Engine control unit
1 FU0638
OPERATION
lThe ignition switch-ST inputs a high signal to the engine control unit while the engine is cranking. Theengine control unit provides fuel injection control, etc., at engine startup based on this signal.
lWhen the ignition switch is set to START, the battery voltage at cranking is applied through the ignitionswitch to the engine control unit, which detects that the engine is cranking.
INSPECTION
Using Multi-use Tester
FunctionItem No. Data displayCheck conditionEngineNormal indication
Data reading18Switch stateIgnition switch: ONstopOFF
CrankingON
HARNESS INSPECTION
1
L6FU1258
2
1
Engine control
side connector
IY-6FU1259
Measure the input voltage to theengine control unit.nlEngine control unit connector:Disconnectedl Ignition switch: START
Check for continuity of the groundcircuit.
lEngine control unit connector:Disconnected
Repair the
harness.
(m - Ground)
iTSB Revision

FUEL SYSTEM - On-vehicle Inspection of MPI Components13-77INSPECTION
Using Multi-use Tester
LIGNITION SWITCH-ST
FunctionItem No. Data displayCheck conditionEngineNormal rndrcation
Data reading18Switch stateIgnition switch: ON
stopOFF
CrankingONINHIBITOR SWITCH
FunctionItem No. Data displayCheck conditionSelect lever positionNormal indicationData reading 29
Shift
Ignition switch: ONP or NP or Nposition
D.2,L or RD.2.L or RHARNESS INSPECTION
@ Harness sideconnector
OlA0206
2
@ Harness srdeconnectorl
Engine control unit connector:
Connectedl
InhibItor switch connector: Dis-6a
L-J
cl3
connectedl Ignition switch: ON
Repair the
harness.Voltage
(VI@El - El)
OlA0206LII
Engine control
unit harness
side connector
Measure the power supply voltage of
the inhibitor switch.
-lEngine control unit connector:
Disconnectedl
lnhibrtor switch connector: Dis-
connectedl Ignition switch: START
Voltage
(V)
rLlltXK IlIt:Lpower supplycircuit.
Measure the inhibitor switch terminalinput voltage.
Measure the input voltage of enginecontrol unit.lEngine control unrt connector:DisconnectedlFer;it;r switch connector: Con-
1 TSB Revision

13-82FUEL SYSTEM - On-vehicle Inspection of MPI Components
AIR CONDITIONER SWITCH AND POWER RELAY
\
*I \\-- \
Air conditronerAir conditioner
control unitAir conditioner
compressor lock
controllerr
Engine control unit
Dual pressureswitch
M13YRAA2
b1IFF
Air conditioner
compressor
Engine control
unit connector
7FUO966
7FUO653
OPERATION
lThe air conditioner switch applies the battery voltage to the engine control unit when the air conditioner is
turned on.
lWhen the air conditioner ON signal is input, the engine control unit drives the idle speed control servo and
turns ON the power transistor. As a result, the air conditioner power relay coil is energized to turn on therelay switch, which activates the air compressor magnetic clutch.
TROUBLESHOOTING HINTS
If the air compressor magnet clutch is not activated when the air conditioner switch is turned on during idling,faulty air conditioner control system is suspected.
INSPECTION
Using Multi-use Tester
AIR CONDITIONER SWITCH
Function1 Item No. 1 Data display 1Check condition) Air conditioner switch 1 Normal indication IData reading 28
Switch stateEngine: Idling (airOFFOFFcompressor to be running
when air conditionerONONswitch is ON)\k”JTSB Revision

FUEL SYSTEM - On-vehicle Inspection of MPI Components
AIR CONDITIONER POWER RELAY
L
FunctionItem No. Data display
Data reading49Air condi-tioner relay
stateCheck conditionEngine: Idling after
warm-up
HARNESS INSPECTIONAir conditioner switch
Normal indication
OFFOFF (compressor
clutch non-activa-
tion)
ONON (compressorclutch activation)
’ I
unit harness
side connector
7FUO695
Measure the power supply voltage of
the air conditioner circuit.l
Air conditioner switch: ONlEngine control unit connector:
Disconnectedl Ignition switch: ON
l
Dual air conditioner switch: ONVoltage
(V)IM
ASTOP
Check the airconditioner
circuit.
AIR CONDITIONER INSPECTIONRefer to GROUP 55
- Service Adjustment Procedures.
TSB Revision