engine oil MITSUBISHI COLT 2008 Owner's Manual (in English)
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2008, Model line: COLT, Model: MITSUBISHI COLT 2008Pages: 450, PDF Size: 14.57 MB
Page 2 of 450
OZME08E2JEA033083
Information for station service
E09300101539
Fuel Capacity
47 litres
Fuel requirements Petrol-powered vehicles
Unleaded petrol octane rating (DIN51607)
95 RON or higher
Diesel-powered vehicles
Cetane number (EN 590)
51 or higher
Refer to the “General information” section for the fuel selection.\
Engine oil “MB 229.1” or higher
Refer to the “Maintenance”section of this manual.
Tyre inflation pressure Refer to the “Maintenance” section for the tyre inflation pressure\
.
For diesel-powered vehicles, the engine oil should be changed every 7,500 km in countries where diesel fuel with a sulphur content
meeting the requirements of EN 590 is not available.
8
Foreword
E09200102098
Thank you for selecting a COLT as your new vehicle.
This owner’s manual will add to your understanding and full
enjoyment of the many fine features of this vehicle.
It contains information prepared to acquaint you with the
proper way to operate and maintain your vehicle for the utmost
in driving pleasure.
MITSUBISHI MOTORS Europe B.V. reserves the right to
make changes relating to design and specifications and/or to
make additions to or improvements in this product without any
obligation to install them on previously manufactured prod-
ucts.
It is an absolute requirement for the driver to strictly observe
all laws and regulations concerning vehicles.
This owner’s manual has been written in compliance with such
laws and regulations, but some of the contents may become
contradictory with later amendment of the laws and regula-
tions.
Please leave this owner’s manual in this vehicle at time of
resale. The next owner will appreciate having access to the
information contained in this owner’s manual.
Repairs to your vehicle:
Vehicles in the warranty period:
All warranty repairs must be carried out by a MITSUBISHI
MOTORS Authorised Service Point.
Vehicles outside the warranty period:
Where the vehicle is repaired is at the owner’s discretion.
Throughout this owner’s manual, the words
WARNING and CAUTION appear.
These serve as reminders to be especially careful. Failure to fol-
low instructions could result in personal injury or damage to your
vehicle.
indicates a strong possibility of severe personal injury or
death if instructions are not followed.
means hazards or unsafe practices that could cause minor
personal injury or damage to your vehicle.
You will see another important symbol:
NOTE: gives helpful information.
*: indicates optional equipment.
It may differ according to the sales classifica-
tion; refer to the sales catalogue.
Abbreviations used in this owner’s manual:
LHD: Left-Hand Drive
RHD: Right-Hand Drive
Page 21 of 450
General information
Fuel selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Filling the fuel tank . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation of accessories . . . . . . . . . . . . . . . . . . . . 5
Modification/alterations to the electrical
or fuel systems . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Genuine parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Used engine oils safety instructions and disposal information . . . . . . . . . . . . . . . . . . . . . . . 7
Page 27 of 450
General information7
Genuine parts
E00200500486
MITSUBISHI MOTORS has gone to great lengths to bring you
a superbly crafted automobile offering the highest quality and
dependability.
Use MITSUBISHI MOTORS Genuine Parts, designed and
manufactured to maintain your MITSUBISHI MOTORS auto-
mobile at top performance. MITSUBISHI MOTORS Genuine
Parts are identified by this mark and are available at all
MITSUBISHI MOTORS Auth orized Service Points.
Used engine oils safety instructions and
disposal information
E00200600025
Protect the environment
It is illegal to pollute drains, water courses and soil. Use
authorized waste collection faci lities, including civic amenity
sites and garages providing facilities for disposal of used oil
and used oil filters. If in doubt, contact your local authority for
advice on disposal.
WARNING!
● Prolonged and repeated contact may cause serious
skin disorders, including dermatitis and cancer.
●Avoid contact with the skin as far as possible and
wash thoroughly after any contact.
● Keep used engine oils ou t of reach of children.
Page 127 of 450
Instruments and controls3-7
3
Indicator and warning lamps
E00501501324
1- Electric power steering warning lamp
→ P. 4-41
2- Supplemental restraint system (SRS) warning lamp →
P. 2 - 7 0
3- High coolant temperature warning lamp → P. 3-13
4- Low coolant temperature indicator lamp → P. 3-8
5- Turn-signal indicator lamps/Hazard warning indicator lamps → P. 3-8
6- Brake warning lamp → P. 3-9
7- Anti-lock brake (ABS) warning lamp → P. 4-38
8- High-beam indicator lamp → P. 3-8
9- Front fog lamp indicator lamp* → P. 3-8
10- Rear fog lamp indicator lamp → P. 3-8
11- Low fuel warning lamp → P. 3-6
12- Door-ajar warning lamp → P. 3-13 13- Traction control system (TCL)/Active stability control sys-
tem (ASC) indicator lamp* → P. 4-44
14- Seat belt warning lamp* → P. 2 - 2 5
15- Front passenger’s air bag off indicator lamp* → P. 2-56
16- Allshift indicator display (vehicles with automated manual transmission) → P. 4-26
17- Oil pressure warning lamp → P. 3-12
18- Charge warning lamp → P. 3-12
19- Check engine warning lamp → P. 3 - 1 1
20- Diesel preheat indicator lamp (diesel-powered vehicles) → P. 3-9
Page 132 of 450
3-12 Instruments and controls
3
Charge warning lampE00502700036
This lamp illuminates when the ignition switch
is turned to the “ON” position, and the lamp goes
off after the engine has started.
In the event of a fault in the charging system, the
warning lamp comes on and a buzzer sounds.
Oil pressure warning lampE00502800053
This lamp illuminates when the ignition switch
is turned to the “ON” position, and the lamp goes
off after the engine has started. If it illuminates
and a buzzer sounds while the engine is running,
the oil pressure is too low.
If the warning lamp illuminates while the engine
is running, turn the engine off and have it
inspected.
NOTE● The oil pressure warning lamp should not
be treated as an indi cation of the engine’s
oil level. The oil level must be checked
using the dipstick.
CAUTION!
● If the warning lamp illuminates and a
buzzer sounds while the engine is run-
ning, there is a problem in the charg-
ing system. In this case, immediately
park your vehicle in a safe place and
we recommend you to have it checked.
CAUTION!
●If this lamp illum inates when the
engine oil level is not low, have it
inspected.
● This warning lamp does not indicate
the amount of oil in the crankcase.
This must be determined by checking
the oil level on the dipstick, while the
engine is switched off.
● If you continue driving with low engine
oil level or with this warning lamp illu-
minated, engine seizure may occur.
Page 202 of 450
4-36 Starting and driving
4
When driving downhill
It is important to take advantage of engine braking by shifting
to a lower shift position while driving on steep downhill roads
in order to prevent the brakes from overheating.
Brake pads and linings
●With new brake pads or linings, avoid where possible sud-
den full application of the brakes for the first 200 km (120
miles) of driving.
● The disc brakes are fitted with a warning device which
emits a shrieking metallic sound while braking if the
brake pads have reached their limit.
If you hear this sound, have the brake pads replaced.
Anti-lock brake system (ABS)
E00607100791
Environmental conditions can ha ve an effect on braking. Dur-
ing sudden braking when there is snow, ice, oil, water etc. on
the road surface, a skid may occur. In this situation, steering
control and braking effectivenes s is reduced and the stopping
distance is increased. The vehicl e may also go into an uncon-
trolled spin.
The ABS helps prevent the wheel s from locking during brak-
ing, thus maintaining directional stability, ensuring controlla-
bility and providing optimum braking force.
Driving hints
● When using the anti-lock brak e system (sudden braking),
steering is slightly different from normal driving condi-
tions. Use the steering wheel carefully.
● Always maintain the same di stance from the vehicle in
front of you as you would for a vehicle not equipped with
ABS.
Compared with vehicles not fitted with ABS, your vehicle
may require a longer stopping distance in the following
cases:
• Driving on gravel or snow-covered roads.
• Driving with tyre chains installed.
• Driving on roads where the road surface is pitted or has
other differences in surface height.
• Driving on bumpy roads or other poor driving surfaces.
WARNING!
●Do not leave any objects ne ar the brake pedal or let
a floor mat slide under it; doing so could prevent the
full pedal stroke that woul d be necessary in an emer-
gency. Make sure that the pedal can be operated
freely at all times. Make sure the floor mat is
securely held in place.
WARNING!
● Driving with worn brake pads will make it harder to
stop, and can cause an accident.
Page 299 of 450
For emergencies6-9
6
Petrol-powered vehicles with turbocharger
The reserve tank lid is equipped with a dipstick.
Remove the dipstick and wipe it with a clean cloth. Rein-
sert the dipstick as far as it will go. Remove the dipstick
and read the coolant level, which should always be within
the range “F” (FULL) or “L” (LOW). 6. Add coolant to the radiator
and/or reserve tank if neces-
sary (refer to the “Maintenance” section).
7. Examine the radiator hoses for coolant leakage and the drive belt for looseness or damage.
If there is anything wrong with the cooling system or
drive belt, we recommend that you have it checked and
repaired.
WARNING!
● If there is none, make sure that the engine has
cooled down before removi ng the radiator cap (B)
(petrol-powered vehicles) or reserve tank cap (C)
(diesel-powered vehicles), because hot steam or boil-
ing water otherwise will gush from the filler port
and may scald you.
FULL
LOW
CAUTION!
● Do not add coolant while the engine is hot. Suddenly
adding cold coolant coul d damage the engine. Wait
for the engine to cool down, then add coolant a little
at a time.
Page 326 of 450
6-36 For emergencies
6To w i n g
E00801501705
If your vehicle needs to be towed
If towing is necessary, we recommend that you have it done by
your MITSUBISHI MOTORS Authorized Service Point or a
commercial tow truck service.
In the following case, transport the vehicle using a tow truck.
● The engine runs but the vehicle does not move or abnor-
mal noise is produced.
● Inspection of the vehicle’s u nderside reveals that oil or
some other fluid is leaking.
If a wheel gets stuck in a ditch, do not try to tow the vehicle.
Please contact your MITSUBISHI MOTORS Authorized Serv-
ice Point or a commercial to w truck service for assistance.
Only when you cannot receive a towing service from a
MITSUBISHI MOTORS Authorized Service Point or com-
mercial tow truck service, tow y our vehicle carefully in accord-
ance with the instructions given in “Emergency towing” in this
part.
The regulations concerning towing may differ from country to
country. It is recommended th at you comply with the regula-
tions of the area where you are driving your vehicle.
Page 339 of 450
Vehicle care7-5
7
●If your vehicle has rain sensor wipers, place the
wiper switch lever in the “ ” (OFF) position to
deactivate the rain sensor before washing the vehi-
cle. Otherwise, the wipers will operate in the pres-
ence of water spray on the windscreen and may get
damaged as a result.
● Refrain from using a car wash as its brushes may
scratch the paint surface, ca using it to lose its gloss.
Scratches will be especially visible on darker col-
oured vehicles.
● Never spray or splash water on the electrical compo-
nents in the engine compartment, as this may
adversely affect engine starting.
Exercise caution also when washing the underbody;
be careful not to spray wa ter into the engine com-
partment.
● Some types of hot water washing equipment apply
high pressure and heat to the vehicle. They may
cause heat distortion and damage to the vehicle resin
parts and may result in floo ding of the vehicle inte-
rior. Therefore; ob serve the following.
• Maintain a good distance of approx. 50 cm or more
between the vehicle body and the washing nozzle.
• When washing around the door glass, hold the
nozzle at a distance of more than 50 cm and at
right angles to the glass surface.
CAUTION!
● After washing the vehicle, drive the vehicle slowly
while lightly depressing the brake pedal several
times in order to dry out the brakes.
Leaving the brakes wet could result in reduced
braking performance. There is also a possibility that
they could freeze up or b ecome inoperative due to
rust, rendering the vehicle unable to move.
● When using an automatic car wash, pay attention to
the following items, referi ng to the operation man-
ual or consulting a car wash operator. If the follow-
ing procedure is not followed, it could result in
damage to your vehicle.
• The outside mirrors are retracted.
• The antenna is removed.
• The rear wiper arm assembly is taped or removed.
• If your vehicle is equipped with a rear spoiler, con- sult a car wash operator be fore using the car wash.
• If your vehicle has rain sensor wipers, place the
wiper switch lever in th e “ ” (OFF) position to
deactivate the rain sensor.
CAUTION!
Page 341 of 450
Vehicle care7-7
7
Cleaning plastic partsE00901300071
Use a sponge or chamois leather.
If a car wax adheres on a grey or black rough surface of the
bumper, moulding or lamps, the surface becomes white. In
such a case, wipe it off using lukewarm water and soft cloth or
chamois leather.
Chrome partsE00901400014
In order to prevent spots and corrosion of chrome parts, wash
with water, dry thoroughly, and apply a special protective coat-
ing. This should be done more frequently in winter.
Aluminium wheels*E00901500086
1. Remove dirt using a sponge while sprinkling water on the wheel.
2. Use neutral detergent on any dirt that cannot be removed
easily with water.
Rinse off the neutral detergent after washing the wheel.
3. Dry the wheel thoroughly using a chamois leather or a soft
cloth.
CAUTION!
● Do not use a scrubbing brush or other hard tools as
they may damage the plastic part surface.
●Do not use wax containing compound (polishing
powder) which may damage the plastic part surface.
●Do not bring the plastic parts into contact with gaso-
line, light oil, brake fluids, engine oils, greases, paint
thinners, and sulphuric ac id (battery electrolyte)
which may crack, stain or discolour the plastic
parts.
If they touch the plastic pa rt, wipe them off with soft
cloth, chamois or the like and an aqueous solution of
neutral detergent then immediately rinse the
affected parts with water.
CAUTION!
● Do not use a brush or other hard implement on the
wheels.
Doing so could scratch the wheels.
●Do not use any cleaner th at contains an abrasive
substance or is acidic or alkaline. Doing so could
cause the coating on the wheels to peel or become
discoloured or stained.
● Do not directly apply hot water using a steam
cleaner or by any other means.
●Contact with seawater an d road deicer can cause
corrosion. Rinse off such su bstances as soon as pos-
sible.