display MITSUBISHI L200 2018 (in English) Owner's Guide

By using the CANCEL switch,the accelerator pedal and the SET - switch
E00633901090
Press the CANCEL switch (D) to deactivate
the Speed Limiter.
Control state “LIMIT” is disappeared and
change control state “LIMIT OFF” in the combination meter.
Accelerate to driver’s desired vehicle speedand push down SET - switch (B) and release.Control state “LIMIT” is displayed again andthe set speed is updated.
To decrease the set speed
E00634000017

By using the SET - switch
E00634101073
Push down the SET - switch (B).

Then the set speed displayed in the combina- tion meter is gradually decreased.
Speed Limiter
6-72OKTE18E1Starting and driving6Type 1 Type 2 Type 1 Type 2

The Speed Limiter indication is displayed
again and the set speed is updated.
To increase the vehicle speed
temporarily
E00634301091
A driver can temporarily accelerate for emer-
gency use.

The Speed Limiter is temporarily deactiva- ted, and the vehicle speed can be increased.
The Speed Limiter will resume when the ve-
hicle speed goes down to enough less than
the set speed.
Put on an accelerator pedal to the pedal
stroke end. (over a detent that makes pedal reaction force bigger before pedal stroke end)
CAUTIONl There is a possibility for the Speed Limiter
to allow abrupt acceleration corresponding
to accelerator pedal position. So be careful
of the abrupt acceleration.If the vehicle speed exceeds the set speed, the
control state “LIMIT” and the Speed Limit-
er’s symbol will blink.CAUTIONl Be careful about over speed.NOTElA driver can change the set speed during this
emergency use.To deactivate
E00634401089
Use whichever following ways to deactivate.
l Press the CANCEL switch
l Press the Speed Limiter ON/OFF switch
Speed Limiter
6-74OKTE18E1Starting and driving6Type 2

NOTElIf the Speed Limiter is cancelled by other
states, it may be a system malfunction.
Stop using the Speed Limiter and turn off
the Speed Limiter. Have your vehicle in-
spected by a MITSUBISHI MOTORS Serv-
ice Point.CAUTIONl There is a possibility for the Speed Limiter
to allow abrupt acceleration corresponding
to accelerator pedal position when the Speed Limiter is deactivated. Be careful.To resume
E00634501077
The Speed Limiter memorizes the set speed
when system has been deactivated, the Speed
Limiter can resume by push up the RES +
switch (C).
However, the Speed Limiter immediately
starts controlling and the vehicle decreases as if an accelerator pedal is closed fully, whenthe vehicle speed is higher than the set speed.
CAUTIONl There is a possibility to occur jerk, depend-
ing on a running resistance. Be careful.Lane Departure Warning
(LDW)* E00635701050
By recognizing through a camera (A) the lane
in which your vehicle is running, LDW gives you warning when your vehicle is likely to drift from its lane with an audible alarm and a
visual alarm displayed on the information
screen of the multi information display.
Lane Departure Warning (LDW)*
6-75OKTE18E1Starting and driving6 Type 1 Type 2

CAUTION•Always keep the windscreen clean.
• Avoid applying a strong shock or pressure
to the LDW camera. Do not attempt to disassemble it.
• Disturbing the installation of the LDW
camera or its removal is under no circum- stances permitted. The camera has been
precisely oriented at the factory.
• Do not put anything like a sticker on the
area in front of the LDW camera lens of the windscreen.
• Use only
MITSUBISHI MOTORS GEN-
UINE Parts when replacing the wind-
screen wipers.Rear-view camera*
E00618402280
The rear-view camera is a system that showsthe view behind the vehicle on a screen of the
MITSUBISHI Multi Communication System
(MMCS), the Smartphone Link Display Au-
dio or the DISPLAY AUDIO.
WARNINGl The rear-view camera is an assistance sys-
tem that enables the driver to check for
obstacles behind the vehicle. Its range of view is limited, so you should not overly depend on it. Please drive just as carefully
as you would if the vehicle did not have
the rear-view camera.WARNINGl Be sure to visually confirm safety around
the vehicle with your own eyes. Do not de-
pend entirely on the rear-view camera.
Range of view of rear-view
camera
The range of view of the rear-view camera is
limited to the area shown in the illustrations.
It cannot show both sides and the lower part of the rear bumper, etc.
When reversing, be sure to visually confirm safety around the vehicle.
Location of rear-view camera
The rear-view camera (A) is integrated into
the part near the rear gate handle.
Range of view of rear-view
camera
Rear-view camera*
6-79OKTE18E1Starting and driving6

How to use the rear-view cam-era
When you place the gearshift lever or the se- lector lever in the “R” position with the igni-
tion switch in the “ON” position or the opera- tion mode in ON, the view behind the vehiclewill automatically appear on the screen of theMITSUBISHI Multi Communication System
(MMCS), the Smartphone Link Display Au- dio or the DISPLAY AUDIO. When you
move the gearshift lever or the selector lever to any other position, the screen will return toits original indication.
CAUTIONl The rear-view camera has a special lens that
can make objects shown on the screen ap- pear to be closer or further away than they
actually are.NOTEl Because the rear-view camera has a special
lens, the lines on the ground between park-
ing spaces may not look parallel on the screen.
l In the following situations, the screen indi-
cation may be difficult to see. There is no abnormality.
• Low light (nighttime).NOTE•When the light of the sun or the light from
a vehicle’s headlamps shines directly into
the lens.
• If a fluorescent light shines directly into
the lens, the screen indication may be
flicker.
There is no abnormality.
l If the camera is hot and is then cooled by
rain or a car wash, the lens can mist up. This
phenomenon does not indicate a malfunc- tion.
l If the atmospheric temperature is extremely
hot or extremely cold, the rear-view camera
images may not be clear.
There is no abnormality.
l If a radio set is installed near the camera, the
rear-view camera images may cause electri- cal system interference and the system may
stop functioning properly.
l It is not possible to fully see obstacles when
the lens is dirty. If the lens becomes conta-
minated by water droplets, snow, mud or oil, wipe off the contamination, taking care not
to scratch the lens.
l Please observe the following cautions. Ig-
noring them could lead to a camera malfunc-tion.
• Do not subject the camera to a physical
shook such as striking it strongly or throwing a thing at it.
• Do not adhere organic substances, waxes,
oil remover, and glass cleaner to the cam-
era.
If adhered to them, immediately wipe off.NOTE• Do not splash the camera with boiling wa-
ter.
• Never spray or splash water on the cam-
era or around it.
• Do not disconnect, disassemble or modify
the camera.
• Do not scratch the camera, as this may
cause damage to the rear-view camera im-
ages.
Reference lines on the screen
Reference lines and upper surface of the rear
bumper (A) are displayed on the screen.
l Red line (B) indicates approximately
50 cm behind the rear bumper.
l Two Green lines (C) indicate approxi-
mately 20 cm outside of the vehicle body.
l Short transverse lines (1 to 3) indicate
distance from the rear bumper.
Check surroundings for safety.
Rear-view camera*
6-80OKTE18E1Starting and driving6

1-Approximately at the rear edge of the
rear bumper
2- Approximately 100 cm
3- Approximately 200 cmCAUTIONl Due to the number of people in the vehicle,
the fuel quantity, the weight and positioning
of luggage, and/or the condition of the road surface, the lines in the view from the rear- view camera may not be accurately posi-
tioned relative to the actual road.
Use the reference lines only as a guideline, and always do a safety check of your behind
and surroundings directly while driving.
Errors between the display and
the actual road surface
The reference lines for distance and vehicle
width are based on a level, flat road surface. In the following cases, errors are produced between the display reference lines and the
distance on the actual road surface.
l When the rear of the vehicle is weigh-
ed down with the weight of passengers
and luggage in the vehicle
The reference lines are displayed closer than the actual distance.
Therefore when there is an obstacle on the
upward slope, it appears farther than its ac-
tual position.
A- Actual objects B- Objects shown on the screen
l When there is an upward slope behind
the vehicle
The reference lines are displayed closer than the actual distance.
Therefore when there is an obstacle on the
upward slope, it appears farther than its ac-
tual position.
A- Actual objects B- Objects shown on the screen
l When there is a downward slope be-
hind the vehicle
The reference lines are displayed farther than the actual distance.
Rear-view camera*
6-81OKTE18E1Starting and driving6

Therefore when there is an obstacle on the
downward slope, it appears closer than its ac- tual position.
A- Actual objects B- Objects shown on the screen
l When solid objects are located close to
the vehicle
When solid objects are located close to the
vehicle, the displayed distance on the screen
may differ from the actual distance.
Because the reference lines do not contact the
body of the truck, it looks as if it would not hit the vehicle in following illustration.
However, the vehicle may hit the truck be-
cause the body of the truck strays onto the course in reality.
l When approaching to solid objects
The reference lines for distance and vehicle
width are intended to indicate the distance toa flat object such as a level, flat road surface.
This may make the distance to a projecting
object shown on the screen differ from the actual distance to the projecting object. Do
not use them as a guide for distances to solid
objects.
Example: On the screen the point B appears the nearest, then the point C and A in order of
distance. The points A and B actually are the same distances from the vehicle, and thepoint C is farther off than the points A and B.
Rear-view camera*
6-82OKTE18E1Starting and driving6 Check surroundings for safety. Check surroundings for safety.

Ventilators........................................................................................... 7-02
Heater/Manual air conditioning*........................................................ 7-04 Automatic climate control air conditioner*........................................ 7-09
Important operation tips for the air conditioning................................ 7-17 Air purifier*........................................................................................ 7-17AM/FM radio/CD player with AUX*.................................................7-18
Handling of Discs................................................................................7-19
Audio Files (MP3/WMA/AAC)..........................................................7-20
Important Points on Safety for the Customer......................................7-24
Operation Keys................................................................................... 7-25 Listen to Radio.................................................................................... 7-28Listen to CDs...................................................................................... 7-29
Listen to MP3s/WMAs/AACs............................................................ 7-30
Listen to an iPod*............................................................................... 7-31 Listen to Audio Files on a USB Device*............................................ 7-33Using AUX*....................................................................................... 7-34
Display Indicator................................................................................. 7-35 Audio Quality and Volume Balance Adjustment............................... 7-36
Time Setting........................................................................................ 7-36
Troubleshooting.................................................................................. 7-38 LW/MW/FM radio/CD player*.......................................................... 7-39
Handling of Discs................................................................................7-42
Audio Files (MP3/WMA/AAC)..........................................................7-43
Important Points on Safety for the Customer......................................7-47
Operation Keys................................................................................... 7-48
Listen to Radio.................................................................................... 7-51
Listen to DAB*................................................................................... 7-52
Listen to Traffic Messages.................................................................. 7-54
Listen to CDs...................................................................................... 7-54Listen to MP3s.................................................................................... 7-55
Listen to an iPod................................................................................. 7-56 Listen to Audio Files on a USB Device.............................................. 7-58To play iPod/USB memory device tracks via voice opera-
tion (vehicles with Bluetooth ®
2.0 interface)................................. 7-60
Listen to Bluetooth Audio*................................................................. 7-63 Display Indicator................................................................................. 7-66
Audio Quality and Volume Balance Adjustment............................... 7-67
System Settings................................................................................... 7-68
Troubleshooting.................................................................................. 7-72
Antenna............................................................................................... 7-75
Link System*...................................................................................... 7-76
Bluetooth ®
2.0 interface*....................................................................7-76
USB input terminal*........................................................................... 7-95
HDMI terminal*..................................................................................7-98
Sun visors............................................................................................ 7-99
Vanity mirror*...................................................................................7-100
Ashtray.............................................................................................. 7-100
Cigarette lighter.................................................................................7-100
Accessory socket............................................................................... 7-101
Digital clock*.................................................................................... 7-101
Interior lamps.................................................................................... 7-102
Storage spaces................................................................................... 7-104
Cup holder......................................................................................... 7-106
Bottle holder......................................................................................7-107
Convenient hook*............................................................................. 7-107
Assist grip......................................................................................... 7-108
Coat hook*........................................................................................ 7-108
First-aid kit and warning triangle securing bands*........................... 7-108For pleasant driving
OKTE18E17

Automatic climate control air conditioner*E00702401638
The air conditioner can only be used while the engine is running.CAUTIONl The engine speed may increase when the air conditioning is operating. With an increased engine speed, an
A/T vehicle will creep to a greater degree than
with a lower engine speed. Fully depress the brake pedal to prevent the vehicle from creeping.

Control panel
E00702502838
1- Temperature control switch
2- Air conditioning switch
3- MODE switch
4- Blower speed selection switch
5- Air selection switch6- Demister switch
7- AUTO switch
8- Rear window demister switch ® p. 5-27
9- OFF switch10- Temperature display ® p. 7-11
11- Air conditioning indicator
12- Mode selection display
13- Blower speed display
Automatic climate control air conditioner*
7-09OKTE18E1For pleasant driving7 Automatic climate control air conditioner - Type 1

1-Driver’s side temperature control switch
(LHD vehicles)
Passenger’s side temperature control
switch (RHD vehicles)
2- Air conditioning switch
3- Blower speed selection switch
4- MODE switch 5- Passenger’s side temperature control
switch (LHD vehicles)
Driver’s side temperature control switch
(RHD vehicles)
6- Air selection switch
7- Demister switch
8- AUTO switch
9- Rear window demister switch ® p. 5-27
10- OFF switch11- Driver’s side temperature display (LHD
vehicles) ® p. 7-11
Passenger’s side temperature display (RHD vehicles) ® p. 7-11
12- DUAL indicator
13- Mode selection display
14- Passenger’s side temperature display
(LHD vehicles) ® p. 7-11
Driver’s side temperature display (RHD vehicles) ® p. 7-11
15- Air conditioning indicator
16- Blower speed displayNOTEl There is an interior air temperature sensor
(A) in the illustrated position.
Never place anything on top of the sensor,
since doing so will prevent it from function- ing properly.
Automatic climate control air conditioner*
7-10OKTE18E1For pleasant driving7Dual-zone automatic climate control air conditioner - Type 2