Set time MITSUBISHI L200 2018 Owner's Manual (in English)
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2018, Model line: L200, Model: MITSUBISHI L200 2018Pages: 466, PDF Size: 28.42 MB
Page 35 of 466
NOTE•The number of times the turn-signal
lamps are flashed by the confirmation function can be changed.
Operation of the Dead Lock
System*
With a vehicle that has a Dead Lock System, it is possible to set the Dead Lock System by
pressing the LOCK switch (1) two times.
Refer to “Dead Lock System*” on page 3-18 for details.
Operation of the outside rear-
view mirrors (Vehicles equip- ped with mirror retractor
switch)
E00310801507
To fold
Locking the doors using the LOCK switch
(1), the outside rear-view mirrors are folded
automatically.
To extend
Unlocking the doors using the UNLOCK
switch (2), the outside rear-view mirrors are
extended automatically.
NOTEl Functions can be modified as stated below.
Please consult a MITSUBISHI MOTORS
Authorized Service Point.
• Automatically extend when the driver’s
door is closed, and then the following op- eration is performed.
[Except vehicles equipped with keyless operation system]
Turn the ignition switch to the “ON” or
“ACC” position.
[Vehicles equipped with keyless operation
system]
Put the operation mode in ON or ACC.
• Automatically retract when the ignition
switch is turned to the “LOCK” position
or the operation mode is put in OFF, and the driver’s door is then opened.
• Automatically extend when the vehicle
speed reaches 30 km/h. NOTE• Deactivate the automatic extension func-
tion.
The outside rear-view mirrors can be fol-
ded or extended by the following opera-
tions, even if changing to any of the above.
After pressing the “LOCK” switch to lock
the doors, if the “LOCK” switch is press- ed again twice in a row within about 30
seconds, the outside rear-view mirrors will retract.
After pressing the “UNLOCK” switch to
unlock the doors, if the “UNLOCK”
switch is pressed again twice in a row within about 30 seconds, the outside rear-
view mirrors will extend again.
l The keyless entry system does not operate in
the following conditions:
• The key is left in the ignition switch. (ex-
cept for vehicles with keyless operation system)
• The operation mode is not in OFF. (vehi-
cles with keyless operation system)
• The door is open.
l The key switch will operate within approxi-
mately 4 m from the vehicle. However, the operating range of the key switch may
change if the vehicle is located near a TV
transmitting tower, power station, or radio
broadcasting station.
l If either of the following problems occurs,
the battery may be exhausted.
Keyless entry system*
3-05OKTE18E1Locking and unlocking3
Page 38 of 466
WARNINGlWhen using electro-medical devices other
than implantable cardiac pacemakers or implantable cardiovascular-defibrillators,
contact the electro-medical device manu- facturer ahead of time to determine theaffects of radio waves on the devices. Elec-
tro-medical device operations could be af- fected by radio waves.
You can limit the possible operations of the
keyless operation system in the following ways. (The keyless operation system can be
used as a keyless entry system.) Please con-
sult a MITSUBISHI MOTORS Authorized
Service Point.
l You can limit operations to locking and
unlocking the doors.
l You can limit operations to starting the
engine.
l The keyless operation system can be dis-
abled.
When keyless operation system operations are modified, the operating transmitters are as
follows.
l Only locking and unlocking doors: exte-
rior transmitter and interior transmitter
l Only starting the engine: interior trans-
mitterNOTEl The keyless operation key uses an ultra-
weak electromagnetic wave. In the following
cases, the keyless operation system may not
operate properly or may be unstable.
• When there is equipment nearby that
emits strong radio waves, such as: a pow-
er station, a radio/TV broadcasting station or an airport.
• The keyless operation system is carried
together with a communications device such as a cellular phone or radio set, or
with an electronic device such as a per- sonal computer.
• The keyless operation key is touching or
covered by a metal object.
• A keyless entry system is being used
nearby.
• When the keyless operation key battery is
worn out.NOTE• When the keyless operation key is placed
in an area with strong radio waves or noise.
In such cases, use the emergency key.
Refer to “To lock/unlock without using
the keyless operation function” on page 3-11.
l Because the keyless operation key receives
signals in order to communicate with the transmitters in the vehicle, the battery con-tinually wears down regardless of keylessoperation key use. The battery life is 1 to 2
years, depending on usage conditions. When the battery wears out, replace the battery ac-cording to the description in this manual or
have it replaced a MITSUBISHI MOTORS
Authorized Service Point.
Refer to “Procedure for replacing the key battery” on page 3-06.
l Because the keyless operation key continual-
ly receives signals, strong radio wave recep- tion could affect battery wear. Do not leave
the key near a TV, personal computer, or
other electronic device.Operating range of the keyless
operation system
E00305701609
If you are carrying the keyless operation key, enter the operating range of the keyless oper-ation system, and press the driver’s or front
passenger’s door lock/unlock switch, the ID
code for your key is verified.
Keyless operation system*
3-08OKTE18E1Locking and unlocking3Double cab
Page 40 of 466
NOTElIf a keyless operation key is too close to the
door or door window, it may be possible to start the engine or change the operation
mode even when the key is outside the vehi- cle.To operate using the keyless
operation function
E00305802173
Locking the doors
When you are carrying the keyless operation
key, if you press the driver’s or front passen- ger’s door lock/unlock switch (A), within theoperating range, the doors are locked.
The turn-signal lamps will blink once.
Also refer to “Locking and unlocking: Doors,
Central door locks” on pages 3-15, and
3-17.
Unlocking the doors
When you are carrying the keyless operation
key, if you press the driver’s or front passen- ger’s door lock/unlock switch (A), within theoperating range, all the doors are unlocked.
If the room lamp switch is in the middle (•)
position at this time, the room lamp will turn
on for 15 seconds. The turn-signal lamps will blink twice.
If the driver’s or front passenger’s door lock/
unlock switch is pressed and any of the doors
is not opened within approximately 30 sec-
onds, relocking will automatically occur. Refer to “Locking and unlocking: Doors, Central door locks” on pages 3-15, and
3-17.
NOTEl For vehicles equipped with the mirror retrac-
tor switch, the outside rear-view mirrors au-
tomatically retract/extend when all the doors are locked/unlocked using the keyless opera-tion function. Refer to “Starting and driving:
Outside rear-view mirrors” on page 6-09.
l For vehicles equipped with the Dead Lock
System, pressing the driver’s or front pas-
senger’s door lock/unlock switch (A) two times in succession causes the Dead Lock
System to be set. (Refer to “Setting the sys-
tem” on page 3-18.)
l The keyless operation function does not op-
erate under the following conditions:NOTE• The keyless operation key is inside the
vehicle.
• A door is open or ajar.
• The operation mode is not in OFF.
l The time between unlocking and automatic
locking can be adjusted. Please consult a
MITSUBISHI MOTORS Authorized Serv-
ice Point.
Operation confirmation when locking and
unlocking
Operation can be confirmed as shown below. However, the room lamp will illuminate only if the room lamp switch is in the middle (•)position.
When locking:The turn-signal
lamps will blink
once.When unlocking:The room lamp illu-
minates for approxi-
mately 15 seconds,
the turn-signal lamps
blink twice.NOTEl Functions can be modified as stated below.
For further information, please contact a
Keyless operation system*
3-10OKTE18E1Locking and unlocking3
Page 42 of 466
Warning activation
E00305902031
In order to prevent vehicle theft or the accidental operation of the keyless operation system, the lamp and buzzer are used to alert the driver.
LampBuzzerItemCauseNote (Solution)Blinks.Outer buzzer sounds
4 times. Inner buzzer
sounds.Keyless operation key
take-out monitoring systemWhen the vehicle is parked with the opera- tion mode in any mode other than OFF, if you close the door after opening any of the
doors and taking the keyless operation key out of the vehicle.
Outer buzzer sounds 4 times at this time.
And when a vehicle starts, inner buzzer
sounds once.l If you take the keyless opera-
tion key out of the vehiclethrough a window without
opening a door, this system does not operate.
l It is possible to change the set-
ting to make the system operate
if you take the keyless opera-
tion key out from the vehicle through a window without
opening a door. For further in- formation, please contact a MITSUBISHI MOTORS Au-
thorized Service Point.
l Even if you have the keyless
operation key within the engine start operating range, if the keyand vehicle ID codes cannot be
matched, for example due to the ambient environment or electromagnetic conditions, the
warning may be activated.
Keyless operation system*
3-12OKTE18E1Locking and unlocking3
Page 46 of 466
2- UnlockNOTElOn vehicles with central door locks, when
locking or unlocking with the key, all doors
will be locked or unlocked.
Refer to “Central door locks” on page 3-17.
l If the vehicle is equipped with the keyless
operation system, the driver’s door can be locked or unlocked with the emergency key.
Refer to “Emergency key” on page 3-11.
To lock or unlock from inside
the vehicle
1- Lock
2- Unlock
NOTEl The driver’s door can be opened without us-
ing the lock knob by pulling on the inside
door handle.
On vehicles with central door locks, all other doors are unlocked at the same time.
l In a vehicle that has a Dead Lock System, it
is not possible to unlock the door by pushing the lock knob to the unlock side while the Dead Lock System is set.
(Refer to “Dead Lock System*” on page
3-18.)
To lock without using the key
Set the inside lock knob (1) to the locked po-
sition, and close the door (2).
NOTEl The driver’s door cannot be locked using the
inside lock knob while the driver’s door is
opened.To open or close the rear door
(Club cab)
E00313800048
You can open or close the rear door while the front door is opened. 1. Open the front door wide.
2. Pull the door handle (A) of the rear door.
3. Open the rear door.
4. When closing these doors, close the
front door after closing the rear door.
Doors
3-16OKTE18E1Locking and unlocking3
Page 49 of 466
2.Get out of the vehicle. Close all of the
doors.
3. Press the LOCK switch (A) on the key,
the driver’s or front passenger’s door lock/unlock switch (C) to lock all of thedoors. The turn-signal lamps will blink
once.
4. Press the switch again within 2 seconds.
The turn-signal lamps will blink three times to show that the Dead Lock Sys- tem has been set.NOTEl Pressing the LOCK switch (A) on the key
once while the Dead Lock System is set cau-ses the turn-signal lamps to blink three
times, so it is possible to confirm that the Dead Lock System is set.Cancelling the system
E00305301458
When the following operation is performed,
the doors will unlock and the Dead Lock Sys- tem will be simultaneously cancelled.
l The UNLOCK switch (B) on the key is
pressed.
l The driver’s or front passenger’s door
lock/unlock switch (C) is pressed while you are carrying the keyless operation
key.
NOTEl If a door is opened within 30 seconds of un-
locking, the doors are automatically relocked
and the Dead Lock System is simultaneously
set again.
l Even when it is not possible to use the key-
less entry system or keyless operation func-
tion to unlock the doors, it is possible to use the key to unlock the driver’s door. When
the key is used to unlock the driver’s door,
the Dead Lock System is cancelled for only the driver’s door. If you wish to subsequent- ly unlock all other doors, turn the ignition
switch to the “ON” or “ACC” position, or put the operation mode in ON or ACC.
l It is possible to adjust the time between
pressing the UNLOCK switch (B) on the key or the driver’s or front passenger’s door
lock/unlock switch (C) and automatic lock-
ing. For details, please contact a MITSUBISHI MOTORS Authorized Serv-
ice Point.
l It is possible to lock the doors and set the
Dead Lock System at the same time with a
single push of the LOCK switch (A) on the key, the driver’s or front passenger’s door
lock/unlock switch (C). For details, please
contact a MITSUBISHI MOTORS Author-
ized Service Point.Testing the system
E00305400159
Open all of the door windows, then set the
Dead Lock System.
(Refer to “Setting the system” on page 3-18.)
Dead Lock System*
3-19OKTE18E1Locking and unlocking3Keyless entry system Keyless operation system
Page 63 of 466
NOTElWhen luggage is placed on the front passen-
ger seat, a sensor in the seat cushion may,
depending on the weight and position of the
luggage, cause the warning tone to sound and the warning lamp to come on. (Club cab
and Double cab)For the rear passenger’s seats*
E00415501047
*-This warning lamp shows the
case of the 5-passenger vehicles.
If the ignition switch is turned to the “ON”
position or the operation mode is put in ON while a seat belt is not fastened, the warning
lamp comes on for approximately 30 seconds to remind the rear passenger to fasten the seatbelt.
If the vehicle is driven with the seat belt still
unfastened, the warning lamps come on for
approximately another 30 seconds. (This illu-
mination happens only the first time the vehi- cle starts moving with the seat belt still un-
fastened.)
The warning lamps go off when the seat belt is fastened.WARNINGl Do not install any accessory or sticker
that makes the lamp difficult to see.NOTEl The warning lamp comes on even if no one
is sitting on the rear seats.
l If a seat belt is unfastened while the vehicle
is being driven, the tone sounds for approxi- mately 1 second and the warning lampcomes on for approximately 30 seconds. At the same time, the warning lamp for the seat
where the seat belt is not fastened comes on.
l If the seat belts are initially fastened but a
seat belt is unfastened while the vehicle is
stationary and the vehicle is then driven with the seat belt still unfastened, the warning
lamp comes on again for approximately 30 seconds.Adjustable seat belt anchor
(front seats of Club cab andDouble cab)
E00405001720
The seat belt anchor height can be adjusted.
To move the anchor, pull the lock knob (A) and slide the anchor to the desired position.
Release the lock knob to lock the anchor into
position.
WARNINGl When adjusting the seat belt anchor, set it
at a position that is sufficiently high so
that the belt will make full contact with your shoulder but will not touch your
neck.
Seat belts
4-09OKTE18E1Seat and seat belts4
Page 94 of 466
NOTElWhen the ignition switch or the operation mode is OFF, the driving range display, average fuel consumption display and outside temperature display are not
displayed.
l While driving, the service reminder is not displayed even if you operate the multi information display switch.
Odometer
E00527801123
The odometer indicates the distance travel-
led.
Tripmeter
E00527901094
The tripmeter indicates the distance travelled between two points.
Example usage of tripmeter
and tripmeter
It is possible to measure two currently
travelled distances, from home using
tripmeter
and from a particular point
on the way using tripmeter
.
To reset the tripmeter
To return the display to 0, hold down the multi information display switch for about 2
seconds or more. Only the currently dis-
played value will be reset.
Example
If tripmeter is displayed, only tripmeter
will be reset.NOTEl When disconnecting the battery terminal, the
memory of tripmeter and are
cleared, and the display returns to “0”.Meter illumination control
E00537901068
Each time you press and hold the multi infor-
mation display switch (2) for about 2 seconds or more, there is a sound and the brightnessof the instruments changes.
1- Brightness level
2- Multi information display switch
Multi-information display
5-04OKTE18E1Instruments and controls5
Page 95 of 466
NOTElYou can adjust to 8 different levels respec-
tively for when the position lamps are illu- minated and when they are not.
Each time you reduce two brightness levels, the segment display of the brightness level decreases one by one.
l If the vehicle is equipped with the automatic
lamp control, when the lamp switch is in a position other than the “OFF” position, the
meter illumination switches automatically to
the adjusted brightness, depending on the
brightness outside the vehicle.
l The brightness level of the instruments is
stored when the ignition switch is turned off or the operation mode is put in OFF.Driving range display
E00538000014
This displays the approximate driving range
(how many more kilometres or miles you can drive). When the driving range falls below
approximately 50 km (30 miles), “---” is dis-
played.
NOTEl The driving range is determined based on
the fuel consumption data. This may vary depending on the driving conditions and habits. Treat the distance displayed as just a
rough guideline.NOTEl When you refuel, the driving range display
is updated.
However, if you only add a small amount of fuel, the correct value will not be displayed.
Fill with a full tank whenever possible.
l On rare occasions, the value displayed for
the driving range may change if you areparked on an extremely steep incline. This is
due to the movement of fuel in the tank and
does not indicate a malfunction.
l The display setting can be changed to the
preferred units (km or miles).
Refer to “Changing the function settings” on page 5-09.Average fuel consumption dis-
play
E00531200033
This displays the average fuel consumption from the last reset to the present time.
The reset mode conditions for the average fuel consumption display can be switched be-
tween “Auto reset” and “Manual reset”.
For information on how to change the aver-
age fuel consumption display setting, refer to “Changing the function settings” on page 5-09.
NOTEl The average fuel consumption display can
be reset separately for the auto reset mode and for the manual reset mode.
l “---” is displayed when the average fuel con-
sumption cannot be measured.
l The initial (default) setting is “Auto reset
mode”.
l The average fuel consumption depends on
the driving condition (road condition, driv- ing behavior, etc.). The displayed fuel con- sumption may vary from the actual fuel con-
sumption. Treat the fuel consumption dis- played as just a rough guideline.
l The memory of the auto reset mode or man-
ual reset mode for the average fuel con-sumption display is erased if the battery isdisconnected.
l The display setting can be changed to the
preferred units {km/L, L/100 km, mpg}.
Refer to “Changing the function settings” on page 5-09.Auto Stop & Go monitor*
E00531101039
The accumulated time the engine has been
stopped by Auto Stop & Go (AS&G) system
is displayed.
Refer to “Auto Stop & Go (AS&G) system” on page 6-23.
Multi-information display
5-05OKTE18E1Instruments and controls5
Page 96 of 466
NOTElWhen the ignition switch or the operation
mode is ON again, the accumulated time
will be reset.Outside temperature display*
E00533501053
This shows the temperature outside the vehi-
cle.
NOTEl The display setting can be changed to the
preferred units (°C or °F).
Refer to “Changing the function settings” on page 5-09.
l Depending on factors such as the driving
conditions, the displayed temperature may vary from the actual outside temperature.Frozen road warning*
E00533401036
If the outside air temperature drops below ap-
prox. 3 °C (37 °F), the alarm sounds and the outside air temperature warning symbol (A)
flashes for about 10 seconds.
CAUTIONl There is a danger the road might be icy, even
when this symbol is not flashing, so please take care when driving.Engine coolant temperature
display
E00533801072
This indicates the engine
coolant temperature.
If the coolant becomes hot, “
” will blink.
Pay careful attention to the engine coolant temperature
display while you are driv-
ing.
CAUTIONl If the engine is overheating, “” will blink.
In this case, the bar graph is in the red zone.
Immediately park the vehicle in a safe place
and take the required measures. Refer to “Engine overheating” on page 8-09.
Multi-information display
5-06OKTE18E1Instruments and controls5