battery MITSUBISHI LANCER 2005 Owner's Guide

DOOR
BODY42-37
INSTALLATION SERVICE POINTS
>>A<< DOOR CHECK INSTALLATION
Install the door check so that the identification mark
faces upwards.
>>B<< LOWER SASH INSTALLATION
Securely insert the rear lower sash into the window
rear sash.
>>C<< DOOR INSIDE HANDLE
INSTALLATION
1. Install the inside lock cable to the door inside
handle as follows:
(1) Install the inner cable end in the inside lock
cable to the clip in the door inside handle.
(2) Turn the inside lock knob to the door lock
position.
(3) Install the outer cable end to the door inside
handle securely.
(4) Install the clip to the inner cable.2. Install the inside handle rod to the door inside
handle.
3. Install the door inside handle to the door.
INSPECTIONM1423004700392
FRONT DOOR LOCK ACTUATOR CHECK
Actuator Operation Check Item Identification
mark
Front Door Left door 39L
Right door 39R
Rear Door Left door 40L
Right door 40R
ACX00541
Identification mark
AB
AC100404
AB
Clip Inner cable
Outer cable end
Inside handle rodDoor inside handleLever
positionBattery connection Lever
operation
At the
"LOCK"
position•Connect terminal
No. 4 and the
negative battery
terminal.
•Connect terminal
No. 6 and the
positive battery
terminal.The lever
moves from the
"LOCK"
position to the
"UNLOCK"
position.
At the
"UNLOCK"
position•Connect terminal
No. 6 and the
negative battery
terminal.
•Connect terminal
No. 4 and the
positive battery
terminal.The lever
moves from the
"UNLOCK"
position to the
"LOCK"
position.
42
53
6 1
42
53
6 1
AC305111B
A
AB
LockUnlock
View A
View B Unlock
Lock Front door
Lever
Lever

DOOR
BODY42-38
Actuator Switch Check
REAR DOOR LOCK ACTUATOR CHECK
Actuator Operation Check
DOOR LOCK KEY CYLINDER SWITCH
CHECK
Lever position Tester
connectionSpecified
condition
At the "LOCK"
position1 − 2 Less than 2
ohms
1 − 3 Open circuit
At the "UNLOCK"
position1 − 2 Open circuit
1 − 3 Less than 2
ohms
23
41
56
23
41
56
AC305112B
A
AB
Rear door
LockUnlock
View A
View B UnlockLock
Lever
Lever
Lever
positionBattery connection Lever
operation
At the
"LOCK"
position•Connect terminal
No. 4 and the
negative battery
terminal.
•Connect terminal
No. 6 and the
positive battery
terminal.The lever
moves from the
"LOCK"
position to the
"UNLOCK"
position.
At the
"UNLOCK"
position•Connect terminal
No. 6 and the
negative battery
terminal.
•Connect terminal
No. 4 and the
positive battery
terminal.The lever
moves from the
"UNLOCK"
position to the
"LOCK"
position.
Switch
positionTester
connectionSpecified
condition
LOCK 2 − 3 Less than 2
ohms
NEUTRAL
(OFF)1 − 2, 2 − 3 Open circuit
UNLOCK 1 − 2 Less than 2
ohms
AC101318
3 2 1

KEYLESS ENTRY SYSTEM
BODY42-51
INSTALLATION SERVICE POINT
>>A<< STRIKER INSTALLATION
Assemble so the distance between the centre of the
striker and centre of the latch is ±1.5 mm or less.
INSPECTIONM1424001200142
TAILGATE LOCK ACTUATOR CHECK
TAILGATE LATCH CHECK keyless entry system>
KEYLESS ENTRY SYSTEM
SERVICE SPECIFICATIONSM1428000300104
AC305098AB
Striker centre
StrikerLatch centre
Latch +1.5 mm
-1.5 mm
AC103292
A
View A
Unlock
Lock Lever
AC
Lever
positionBattery connection Lever
operation
At the
"LOCK"
position•Connect terminal
No.2 and the
negative battery
terminal.
•Connect terminal
No.3 and the
positive battery
terminal.The lever
moves from the
"LOCK"
position to the
"UNLOCK"
position.
At the
"UNLOCK"
position•Connect terminal
No.3 and the
negative battery
terminal.
•Connect terminal
No.2 and the
positive battery
terminal.The lever
moves from the
"UNLOCK"
position to the
"LOCK"
position.
Lever position Tester
connectionSpecified
condition
At the "LOCK"
position1 − 2 (Earth) Open circuit
At the
"UNLOCK"
positionLess than 2
ohms
AC103291
Lever
Unlock Lock
1
2
AD
Item Standard value
Voltage of transmitter battery V 2.5 − 3.2

KEYLESS ENTRY SYSTEM
BODY42-58
7. If you are using two or more transmitters or have
added a second transmitter, the same registration
procedure should be carried out within one minute
after registering the code for the first transmitter.
8. Registration mode will be cancelled under the
following conditions:
•When the secret code for four transmitters has
been registered;•When one minute has passed after registration
mode started;
•When the V.C.I. is disconnected from the
diagnosis connector;
•When the key is removed from the key cylinder;
9. After the registration is completed, remove the
ignition key and close all the doors, and then
check that the keyless entry system operates
normally.
TRANSMITTER
DISASSEMBLY AND REASSEMBLYM1428002800172
Post-reassembly operation
•Transmitter operation check
AC310838AC303199
AC3041181 2
AF
5
3
4
6
Disassembly steps
1. Screw
2. Upper cover
3. Transponder4. Transmitter assembly
<> >>A<<5. Battery
6. Master keyDisassembly steps (Continued)

KEYLESS ENTRY SYSTEM
BODY42-59
DISASSEMBLY SERVICE POINT
<> BATTERY REMOVAL
CAUTION
Do not allow water or dust to enter the inside of
the transmitter assembly when it is open. Also,
do not touch the precision electronic device.
REASSEMBLY SERVICE POINT
>>A<< BATTERY INSTALLATION
CAUTION
Do not allow water or dust to enter the inside of
the transmitter assembly when it is open. Also,
do not touch the precision electronic device.Install a new battery to the transmitter assembly with
its (+) side facing towards the upper cover side.
Battery required for replacement: Coin type
battery CR1616
INSPECTIONM1428003800067
TRANSMITTER BATTERY CHECK
Measure the voltage of the battery. If the voltage of
the battery is not within the standard value, replace
the battery.
Standard value: 2.5 − 3.2 V
AC304118
AD
+ –
Master key sideUpper cover side
Battery Transmitter assembly
AC004486

WINDSHIELD WIPER AND WASHER
EXTERIOR51-25
INSPECTIONM1511007700313
FRONT WIPER MOTOR CHECK
Inspect the windshield wiper motor by removing the
harness connector with the motor attached to the
vehicle.
Wiper Motor at Low-Speed and
High-Speed Operation
Connect the battery to the windshield wiper motor to
inspect the operation of motor rotation in low or high
speed.
Wiper Motor at Stop Position Operation
1. Connect the battery to the windshield wiper motor
to rotate the motor in a low speed as shown in the
illustration (A) and disconnect the battery during
rotation to stop the motor.
2. Connect between the terminals and the battery as
shown in the illustration (B) and confirm whether
the motor stops at the automatic stop position
after rotating in a low speed.
FRONT WASHER MOTOR CHECK
1. Remove the washer tank assembly with the
washer hose attached. Then fill the washer tank
with water.
2. Check to see that the water is vigorously spray is
when connecting the positive battery terminal to
terminal number 2 and terminal number 1 to the
negative battery terminal.
1
423
5
1
423
51
423
5
1
423
5
AC305201
1
423
5
Check operation
Low speed High speed
(A) Low speed (B) Automatical stop
Stop position check
AB
1
2
AC005891

REAR WIPER AND WASHER
EXTERIOR51-30
INSTALLATION SERVICE POINTS
>>A<< REAR WIPER ARM AND BLADE
ASSEMBLY INSTALLATION
Before installing the rear wiper arm and blade
assembly, operate the rear wiper motor so that the
motor stops at the predetermined park position.
Install the rear wipe arm and blade assembly and
adjust the rear wiper blade position so that the blade
end stops at the predetermined position (standard
position).
Standard value (A): 42 ± 5 mm
>>B<< WIPER BLADE INSTALLATION
CAUTION
Use a curved backing like that shown for the
backing of a wiper blade to ensure sustained
wiper wiping performance.
INSPECTIONM1511008600193
REAR WIPER MOTOR CHECK
Inspect the rear wiper motor is conducted by
removing the harness connector with the motor
attached to the vehicle.
Wiper Motor Operation
Connect the battery to the rear wiper motor as shown
in the illustration (A) and check the motor operation.
Wiper Motor at Stop Position Operation
1. Connect the battery to the rear wiper motor as
shown in the illustration (A).
2. Disconnect the battery cable from the rear
windshield wiper motor while it is turning and then
check to see that the motor stops.
3. Re-connect the battery as shown in Figure (B).
4. Check to see that the rear windshield wiper motor
runs and then stops at the automatic stop
position.
AC304536
A
AC
End of tailgate glass
AC101090AD
Wiper bladeBacking
BackingA
A
Section A – A
Wiper
bladeBacking
AB304538
1234
1234
1234
AB
(A) Operation check
(B) Stop position check

REAR WIPER AND WASHER
EXTERIOR51-31
REAR WASHER MOTOR CHECK
1. Remove the rear washer tank assembly with the
washer hose attached. Then fill the washer tank
with water.
2. Check to see that the water is vigorously sprayed
when connecting the positive battery terminal to
terminal number 2 and terminal number 1 to the
negative battery terminal.
REAR WASHER FLUID EJECTION CHECK
CAUTION
Take care not to damage the nozzle when
inserting the flat-tipped screwdriver into it.For the vertical aiming of washer nozzle, insert the
flat-tipped screwdriver into the nozzle and move it to
the arrow direction.
REAR WIPER AND WASHER SWITCH
CHECK
Check continuity between the switch terminals.
1
2
AC005900
AC304544AB
UNITS: mm
57 841256 Section A – A
A A
High-mounted
stop lampRear washer nozzle
Flat-tipped screwdriverWindshield ceramic
line terminal
Windshield washer
nozzle perpendicular
Switch position Tester
connectionSpecified
condition
OFF 4 − 6, 5 − 6 Open circuit
Rear wiper switch 4 − 6 Less than 2
ohms
Rear washer
switch5 − 6
1
6
8
11 109 7
5 4
3
2
AC000417

HEADLAMP WASHER
EXTERIOR51-33
INSPECTIONM1511009800082
HEADLAMP WASHER MOTOR CHECK
1. Remove the headlamp washer motor connector.
2. Check to see that the water is vigorously sprayed
when connecting the positive battery terminal to
terminal number 1 and terminal number 2 to the
negative battery terminal.
7. Headlamp washer motor
8. Headlamp washer gasket
•Front bumper (Refer to P.51-2).
9. Headlamp washer actuator
assembly
10. O-ring
11. Headlamp washer hose assembly Removal steps (Continued)
AC304136AB
12

DOOR MIRROR
EXTERIOR51-47
INSPECTIONM1511006500286
ELECTRIC REMOTE CONTROL MIRROR
OPERATION CHECK WITHOUT HEATED DOOR MIRROR>
Check that the mirror moves as described in the
table when each terminal is connected to the battery.
ELECTRIC REMOTE CONTROL MIRROR
OPERATION CHECK HEATED DOOR MIRROR>
Check that the mirror moves as described in the
table when each terminal is connected to the battery.
Battery connection Direction
operation
•Connect terminal 1 to the negative
battery terminal.
•Connect terminal 3 to the positive
battery terminal.Mirror
glass
should face
upward
•Connect terminal 3 to the negative
battery terminal.
•Connect terminal 1 to the positive
battery terminal.Mirror
glass
should face
downward
•Connect terminal 1 to the negative
battery terminal.
•Connect terminal 2 to the positive
battery terminal.Mirror
glass
should face
to the right
•Connect terminal 2 to the negative
battery terminal.
•Connect terminal 1 to the positive
battery terminal.Mirror
glass
should face
to the left
3 2
1
AC005969
Battery connection Direction
operation
•Connect terminal 5 to the negative
battery terminal.
•Connect terminal 7 to the positive
battery terminal.Mirror
glass
should face
upward
•Connect terminal 7 to the negative
battery terminal.
•Connect terminal 5 to the positive
battery terminal.Mirror
glass
should face
downward
•Connect terminal 5 to the negative
battery terminal.
•Connect terminal 6 to the positive
battery terminal.Mirror
glass
should face
to the right
•Connect terminal 6 to the negative
battery terminal.
•Connect terminal 5 to the positive
battery terminal.Mirror
glass
should face
to the left
AC202548
1
456723