ignition MITSUBISHI LANCER EVOLUTION 2010 10.G MMCS Manual

Starting the MMCS 2-1
Basic Operation
Basic Operation
Starting the MMCS
WARNING
 Do not operate the Mitsubishi Multi Communication
System (MMCS) while driving. Always concentrate on your driving rst. Keep your

eyes and mind on the road. If distracted while
driving, you could cause an accident.
 When operating the MMCS, do not park with the
engine running in a closed or poorly ventilated
area. Carbon monoxide gas, which is odorless and
extremely poisonous, can build up and cause serious
injury or death.
1 Turn “ON” the ignition switch
eng_244

eng_a002
The opening screen is displayed.

If any function other than AUDIO was used last time,
go to Step 2.NOTE If special days and anniversaries
(page 9-1)
have
been set, when the date matches the settings, the
set icon is displayed on screen.
 If maintenance information
(page 9-9)
has been set,
when the maintenance distance has been exceeded
or the maintenance timing has been exceeded, a
telop will be displayed in the opening screen.
2 Touch the desired language
eng_a001-1
NOTE When the meter is set to Auto, the language of both
sides can be changed by performing operations on
either the MMCS side or the meter side.
 When the meter is set to Manual, the language
of the meter side and the MMCS side can be set
separately. 3 Touch [OK]
After a moment, the display is changed to the
navigation screen.NOTE If the battery voltage is low in cold regions, etc., the
navigation screen is displayed rather than the screen
last used.






 


Trip 9-5
Information
Trip
Trip information can be viewed and set.
1 Press the [INFO] key, and touch
[Trip]
eng_a140

eng_a208
The trip screen is displayed.
The average speed, Average Fuel Economy, and
Instant Fuel Economy information can be viewed.NOTE Touch [Graph] to view
the average speed and
average fuel economy
as a graph, measured
in 5-minute units.
eng_a211
 Touch [Manual] to change the reset mode to “Manual
Reset Mode”.
>>> “Reset Mode” (page 9-5)
2 Touch [
]

eng_a209
The 2/3 trip screen is displayed.
The distance to empty, distance driven after refueling
and driving time can be viewed. 3 Touch [
]

eng_a210
The 3/3 trip screen is displayed.
The lap time can be measured. >>> “Lap Time” (page 9-6)
Reset Mode
Two reset modes are available:
- Auto Reset Mode automatically resets
the average speed and average fuel
economy, four hours after the ignition
switch is turned OFF.
- In Manual Reset Mode, you can reset
the items when desired.
Changing the Reset Mode
1 Display the 1/3 Trip screen
2 Touch [Manual]
eng_a208

eng_a212
“Auto Reset Mode” is changed to “Manual Reset
Mode”.










Trip 9-6NOTE Touch [Auto] to return to “Auto Reset Mode”.
 In “Manual Reset Mode” or “Auto Reset Mode”,
touch [Reset] to reset the average speed and
average fuel economy.
Driving Distance and Time
The distance to empty, distance driven
after refueling and driving time can be
viewed on the 2/3 Trip screen.
Distance to EmptyThe displayed distance to empty is calculated from
the current remaining fuel and the recent average fuel
economy.Distance Driven After RefuelingDisplays automatically the distance driven after
refueling.
It is reset when the vehicle is refueled.NOTE If the amount of fuel added is less than approximately
2.6 gallons (10 litres), automatic reset will not be
performed. Press [Refuel] to reset.Driving TimeMeasures the time from when the ignition switch is
turned “ON” to when it is turned “OFF”.
It is reset when the ignition switch is turned from “OFF”
to “ON”.
Lap Time
Time, distance, speed and mileage can be
measured.
1 Display the 3/3 Trip screen
2 Touch [Start]
eng_a210

Total Line
eng_a213
The measurement starts. At this time, the speed and
mileage are being measured, so they are not displayed. 3 Touch [Lap]

eng_a214
The current measurement results are displayed in “A”.
NOTE Touch [Lap] again
and the measurement
results displayed in
“A” are moved to
“B”, and the current
measurement results
are displayed in “A”.
eng_a215
4 Touch [Stop]

eng_a216
The measurements stop and the measurement results
are displayed in the total line.NOTE Touch [Start] to restart the measurements from
where they stopped.
 The measurements stop if the ignition switch is
turned “OFF” during measurement. If this happens,
the measurements restart when the ignition switch is
turned “ON”. 5 Touch [Reset]