remote control MITSUBISHI LANCER RALLIART 2010 8.G Owner's Manual
[x] Cancel search | Manufacturer: MITSUBISHI, Model Year: 2010, Model line: LANCER RALLIART, Model: MITSUBISHI LANCER RALLIART 2010 8.GPages: 670, PDF Size: 25.18 MB
Page 155 of 670
3-64 Features and controls
3
At this time, the theft-alarm indicator (A) on the audio
panel flashes for confirmation.
4. The system has entered the armed stage after about 20
seconds, when the theft-alarm indicator (A) flashing
becomes slower.
The theft-alarm indicator (A) continues to flash while the
system is in the armed stage.
NOTEThe system will be disarmed if, while the theft-alarm indi-
cator (A) is illuminated, all doors are unlocked by remote
control transmitter, the F.A.S.T.-key.
The system will be disarmed if, while the theft-alarm indi-
cator is illuminated, the ignition switch is turned to “ON”
or “ACC”.
The system will not be armed if a door or a trunk lid is not
completely closed. If this happens, rearm the system as
described above.
The driver should not arm the system until first confirm-
ing that all passengers have left the vehicle. If the driver
arms the system with passenger(s) in the vehicle, the
alarm may be activated when the passenger(s) open the
door.
BK0102103US.book 64 ページ ２００９年１０月２６日 月曜日 午後１時３８分
Page 156 of 670
Features and controls
3-65
3
Alarm stageWhile the vehicle is parked and the system is armed, the alarm
will be activated if one of the doors or a trunk lid is opened
without the remote control transmitter or the F.A.S.T.-key.Type of alarmWhen the alarm is activated:
1. The headlights blink on and off for 3 minutes.
After 3 minutes the headlights automatically shut off.
2. The horn will sound intermittently for 3 minutes.
NOTEThe alarm will continue to operate for 3 minutes. At the
end of that period, the alarm will automatically shut off to
save battery power. The system will then be rearmed until
the proper disarming step is taken.
While the alarm is operating, it is displayed on the infor-
mation screen in the multi-information display.
Ty p e 1
Ty p e 2Alarm deactivationThe alarm can be deactivated in the following ways.
By using the remote control transmitter or the F.A.S.T.-
key to lock or unlock the door.
Turn the ignition switch to the “ON” or the “ACC” posi-
tion.
Horn sounds!
Headlights blink on and off!
BK0102103US.book 65 ページ ２００９年１０月２６日 月曜日 午後１時３８分
Page 157 of 670
3-66 Features and controls
3
Disarmed stageThe system will be disarmed when either of the following steps
are taken:
1. All doors are unlocked by the remote control transmitter,
the F.A.S.T.-key.NOTEIf the UNLOCK button is pressed when all doors are
closed and no door is opened within approximately 30
seconds, re-arming will automatically occur.
2. The ignition switch is turned to the “ACC” or “ON” posi-
tion.NOTEOnce the system has been disarmed, it cannot be rearmed
except by repeating the arming procedure.
Testing the theft-alarm systemUse the following procedure to test the system:
1. Lower the driver’s window.
2. Arm the system as explained in “Armed stage”.
3. Make sure that the theft-alarm indicator comes on and
flashes within approximately 20 seconds.
4. Wait a few seconds and then unlock the driver’s side door
by using the inside door lock knob and opening the door.
5. Check to be sure that the horn sounds intermittently and
the headlights blink on and off when the doors is opened.
6. Disarm the system by unlocking all doors by the remote
control transmitter, the F.A.S.T.-key.
Disarm...by remote control transmitter or F.A.S.T.-keyBK0102103US.book 66 ページ ２００９年１０月２６日 月曜日 午後１時３８分
Page 313 of 670
3-222 Features and controls
3
Headlight flasher
N00550000198
You can flash the high beams by pulling the lever gently
toward you (2). The lights will go back to normal when you let
go. While the high beam is on, you will see a blue light on the
instrument panel.NOTEYou can flash the high beams by pulling the lever toward
you, even if the combination headlights and dimmer
switch is off.
If you turn the lights off with the headlights set to high-
beam illumination, the headlights are automatically
returned to their low-beam setting when the combination
headlights and dimmer switch is next turned to the “ ”
position.
Welcome light (for vehicles equipped with the
color multi-information display)
N00563200019
This function turns on the front side-marker and parking lights
for about 30 seconds after the UNLOCK button (A) on the
remote control transmitter is pressed when the combination
headlights and dimmer switch is in the “OFF” or “AUTO”
position (for vehicles equipped with the automatic light con-
trol). If the combination headlights and dimmer switch is in the
“AUTO” position (for vehicles equipped with the automatic
light control), the welcome light function will operate only
when it is dark outside the vehicle.
BK0102103US.book 222 ページ ２００９年１０月２６日 月曜日 午後１時３８分
Page 314 of 670
Features and controls
3-223
3
NOTEWhile the welcome light function is operating, perform
one of the following operations to cancel the function.
• Push the LOCK button (B) on the remote control trans-
mitter.
• Turn the combination headlights and dimmer switch to
the “ ” or “ ” position.
• Turn the ignition switch to the “ON” position.
It is possible to modify functions as follows:
• The headlights can be set to come on in the low beam
setting instead of the front side-marker and parking
lights.
• The welcome light function can be deactivated.
For details, consult a Mitsubishi Motors dealer.
Coming home light (for vehicles equipped with
the color multi-information display)
N00547300012
This function turns on the headlights in the low beam setting
for about 30 seconds after the ignition switch is turned to the
“LOCK” position.
1. Turn the combination headlights and dimmer switch to the
“OFF” or “AUTO” position (for vehicles equipped with
the automatic light control).
2. Turn the ignition switch to the “LOCK” position. Also, if
a key was used to start the engine, remove the key from
the ignition switch.
3. Within 60 seconds of turning the ignition switch to the
“LOCK” position, pull the turn signal lever toward you.
BK0102103US.book 223 ページ ２００９年１０月２６日 月曜日 午後１時３８分
Page 366 of 670
Features and controls
3-275
3
Reading lights
N00553800067
Regardless of the dome light switch position, when you press
the lens, the light on the side that is pressed illuminates; when
you press the lens again, the light goes off.
In vehicles equipped with the keyless entry system, the
keyless entry system remote control transmitter is used
to lock the doors.
In vehicles equipped with the F.A.S.T.-key, the doors
are locked using the F.A.S.T.-key.NOTEWhen the engine is started using the key while the
doors are closed, if you remove the key, the dome light
will illuminate for about 30 seconds before going off.
When the engine is started using the F.A.S.T.-key while
the doors are closed, if the ignition switch is moved to
the “LOCK” position, the dome light will illuminate
for about 30 seconds before going off.
The time until the light goes off can be adjusted. See
your authorized Mitsubishi Motors dealer for details.
For vehicles equipped with the Mitsubishi Multi-Com-
munication System, adjustments can be made using
screen operations. For details, refer to the separate
owner’s manual.
2- (OFF)
The dome light goes off.
BK0102103US.book 275 ページ ２００９年１０月２６日 月曜日 午後１時３８分
Page 367 of 670
3-276 Features and controls
3
Dome light (Rear)
(if so equipped)
N00525400361
The dome light can be turned on by sliding the dome light switch.
1- (ON)
The dome light comes on.
2- ()
The dome light comes on when any door is opened. When all
the doors are closed, the dome light illuminates for about 30
seconds then goes off. However, the light goes off immedi-
ately if:
The door is closed while the ignition switch is in the
“ON” position.
The driver’s door is closed after all the other doors are
closed while the lock knob of the driver’s door is in the
lock position.
The door is closed and the power door lock switch is
used to lock the doors.
In vehicles equipped with the keyless entry system, the
keyless entry system remote control transmitter is used
to lock the doors.
In vehicles equipped with the F.A.S.T.-key, the doors
are locked using the F.A.S.T.-key.NOTEWhen the engine is started using the key while the
doors are closed, if you remove the key, the dome light
will illuminate for about 30 seconds before going off.
When the engine is started using the F.A.S.T.-key while
the doors are closed, if the ignition switch is moved to
the “LOCK” position, the dome light will illuminate for
about 30 seconds before going off.
The time until the light goes off can be adjusted. See
your authorized Mitsubishi Motors dealer for details.
For vehicles equipped with the Mitsubishi Multi-Com-
munication System, adjustments can be made using
screen operations. For details, refer to the separate
owner’s manual.
3- (OFF)
The dome light goes off.
BK0102103US.book 276 ページ ２００９年１０月２６日 月曜日 午後１時３８分
Page 390 of 670
5
Comfort controls
Vents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5- 2
Heater without air conditioning function
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . .5- 6
Manual air conditioning with MAX A/C mode
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . .5- 12
Manual air conditioning without MAX A/C mode
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . .5- 22
Automatic air conditioning with Fahrenheit scale
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . .5- 31
Automatic air conditioning with Celsius scale
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . .5- 41
Important air conditioning operating tips . . . . . . .5- 51
Air purifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5- 52
AM/FM electronically tuned radio with CD player
(RBDS and MP3 compatible)
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . .5- 52
AM/FM electronically tuned radio with 6 CD
autochanger (RBDS and MP3 compatible)
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . .5- 80
To use the external audio input function
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . .5- 110Steering wheel audio remote control switch
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . 5- 112
Error codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5- 115
Error codes (SIRIUS Satellite Radio)
(if so equipped) . . . . . . . . . . . . . . . . . . . . . . . . . 5- 117
Handling of compact discs (CD) . . . . . . . . . . . . . . 5- 119
Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5- 122
Digital clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5- 124
General information about your radio . . . . . . . . . . 5- 125
BK0102103US.book 1 ページ ２００９年１０月２６日 月曜日 午後１時３８分
Page 501 of 670
5-112 Comfort controls
5
NOTEThe connected audio equipment cannot be operated with
the vehicle’s audio system.
Depending on the connected audio equipment, it may pro-
duce noise from the speakers.
Use the connected audio equipment’s own power source,
such as its battery.
Noise may be produced from the speakers if the connected
audio equipment is used while charging it using the 12 V
power outlet of the vehicle.
Do not activate the external audio input mode when no
audio equipment is connected.
Otherwise, noise may be produced from the speakers.
Connect audio equipment when the external audio input
mode is deactivated or lower the vehicle’s speaker volume
before connecting it.
Noise may be produced from the speakers if audio equip-
ment is connected after the external audio input mode is
activated.
For information on how to connect and operate the audio
equipment, refer to the owner’s manual for the equipment.
Steering wheel audio remote control switch
(if so equipped)
N00714800396
The remote control switch is located on the left side of the
steering wheel.
The switch can be operated when the ignition switch is in
either the “ON” or “ACC” position.Type 1
BK0102103US.book 112 ページ ２００９年１０月２６日 月曜日 午後１時３８分
Page 502 of 670
Comfort controls
5-113
5
NOTEDo not press multiple buttons at the same time when using
the steering wheel audio remote control switch.To turn on the powerPress the power switch (3) to turn on the power. When the
power is turned on, the last mode used before turning off is dis-
played. To turn off the power, press and hold down the power
switch (3) for about 2 seconds until you hear a beep.
Vo l u m e c o n t r o lVolume up button - 1While the button is pressed, the volume will continue to
increase.Volume down button - 2While the button is pressed, the volume will continue to
decrease.Mode selectionPress the mode selector button (3) to select the desired mode.
The mode changes in the following order.
AM → FM1 → FM2 → (SAT1 → SAT2 → SAT3 → SAT4) →
CD → (RSES) → AMTo listen to the radioPress the mode selector button (3) and select AM or FM mode.Automatic tuningSeek up button - 4 / Seek down button - 5
After pressing one of these buttons, a receivable station will be
automatically selected and reception of the station will begin.Channel selection / Category selection (Vehicles with
satellite radio)Seek up button - 4 / Seek down button - 5
Press the button to select the desired channel.
Pressing down the button for 2 seconds or longer will change
the system to category selection mode. While the button is
pressed, the category will change in order. When you reach the
desired category, release the button.
1- Volume up button
2- Volume down button
3- Power switch/mode selector button
4- Seek up/track up/fast-forward button
5- Seek down/track down/fast-reverse buttonType 2
BK0102103US.book 113 ページ ２００９年１０月２６日 月曜日 午後１時３８分